- 您现在的位置：买卖IC网 > PDF目录19192 > HR10A-TC-02 (Hirose Electric Co Ltd)TOOL CABLE CRIMP FOR HR10/H25 PDF资料下载
参数资料
| 型号： | HR10A-TC-02 |
| 厂商： | Hirose Electric Co Ltd |
| 文件页数： | 11/20页 |
| 文件大小： | 0K |
| 描述： | TOOL CABLE CRIMP FOR HR10/H25 |
| 标准包装： | 1 |
| 系列： | HR10, HR25 |
| 工具类型： | 手动压接器，线缆 |
| 适用于相关产品： | 5.0mm、7.0mm 直径线缆 |
| 特点： | 侧面插入 |
| 产品目录页面： | 415 (CN2011-ZH PDF) |
| 其它名称： | *HR10A-TC-02 H9974 HR10A-TC-02-ND Q914038 |
The product information in this catalog is for reference only. Please request the Engineering Drawing for the most current and accurate design information.
HR10 Series ● Push-Pull Connectors
■ Cable connecting methods
HR10B-2.5CP
HR10B-2.5CJ
1.Cable end treatment
3.Crimping cable outer conductor
Fig.1
11±0.5
Fig.3
(HR10B-2.5CP)
A
1.4±0.2
(2.5) 3.7±0.2
Slit cable outer jaket
2 pieces (180° reverse side)
Clamp metal
Connector
Remove excess insulator
material (remaining after
clamping is complated)
with a knife or aimilarobject.
1.Dimensions for cable end treatment are shown in
Table 1 dimenshion A
Fig 1.
2.Termination is described below.
(1).Strip cable outer jacket as indicated.
2.5CP
1.5±0.2mm
2.5CJ
0 +0.3 mm
(2).Slit outer jacket on both sides per Fig.1.
(3).Fold back outer cover.
(4).Remove insulator from cable.
2.Soldering male pin to cable center
conductor.
Fig.2
Malu pin or Female pin
Soldering
1. Insert cable prepared per PROCESS 2 into the
connector.The cable should be inserted until it
comes to a full stop.This may be verified by
checking the dimension from the side of the
connector to the top of the contact(as indicated in
Fig 3). This dimension should be A.
2. Crimp this installed metal clamp with tool HR10-
TC-01 per Fig.3 and remove excess insulation with
a knife.
It is possible to pull back the contact.
Hold cable when crimping metal clamp and keep
the dimension to show in Fig 3. after crimping metal
clamp.
Should fix flush
Contact fixing jig
such as vise
1.Solder male pin to cable center conductor as
indicated in Fig.2.
(1).Pre-solder the solder pot of pin with ? 0.5mm
string solder.
(2).Male pin should fit flush against the cable
insulator as shown.
(3).Remove any excess solder from the pin with a
knife.This surface must be smooth.
(4).A properly soldered terminal will yield 500gf
when stretched.
189
相关PDF资料 |
PDF描述 |
|---|---|
| 210-12MST | SWITCH RAISED ACTUATOR 12 SEC |
| HR10A-TC-04 | TOOL CABLE CRIMPER |
| 210-12LPST | SWITCH SPST 12 SEC TAPE SEAL |
| FQB50N06LTM | MOSFET N-CH 60V 52.4A D2PAK |
| CUB7TVR0 | TIMER LCD PROGRAM 8-DIGIT HV RED |
相关代理商/技术参数 |
参数描述 |
|---|---|
| HR10A-TC-02HANDLESPRIN | 制造商:Hirose 功能描述: |
| HR10A-TC-03 | 功能描述:环形推拉式连接器 LOW COST MODEL RoHS:否 制造商:Hirose Connector 产品类型:Connectors 系列:HR10 触点类型:Socket (Female) 外壳类型:Receptacle 触点数量:4 外壳大小:7 安装风格:Panel 端接类型:Solder 电流额定值:2 A |
| HR10A-TC-04 | 功能描述:折皱器 Crimp Tool HR10 Series RoHS:否 制造商:Hirose Connector 类型: 描述/功能:Cable and Shield Crimper |
| HR10B-10JA-10SC(73) | 功能描述:环形推拉式连接器 10P F STRT JACK CRMP PSH-PUL CON COAX TRM RoHS:否 制造商:Hirose Connector 产品类型:Connectors 系列:HR10 触点类型:Socket (Female) 外壳类型:Receptacle 触点数量:4 外壳大小:7 安装风格:Panel 端接类型:Solder 电流额定值:2 A |
| HR10B-10P-10PC(73) | 功能描述:环形推拉式连接器 10P M STRT JACK CRMP PSH-PUL CON COAX TRM RoHS:否 制造商:Hirose Connector 产品类型:Connectors 系列:HR10 触点类型:Socket (Female) 外壳类型:Receptacle 触点数量:4 外壳大小:7 安装风格:Panel 端接类型:Solder 电流额定值:2 A |
发布紧急采购，3分钟左右您将得到回复。