- 您现在的位置：买卖IC网 > PDF目录7998 > HR30-7P-C (Hirose Electric Co Ltd)CONN DUST CAP FOR 10&12POS PLUG PDF资料下载
参数资料
| 型号： | HR30-7P-C |
| 厂商： | Hirose Electric Co Ltd |
| 文件页数： | 10/12页 |
| 文件大小： | 0K |
| 描述： | CONN DUST CAP FOR 10&12POS PLUG |
| 标准包装： | 20 |
| 系列： | HR30 |
| 附件类型： | 帽盖（盖） |
| 适用于相关产品： | HR30 系列插头 |
| 外壳尺寸 - 插件： | 7 |
| 颜色： | 黑 |
| 配用： | HR1916-ND - CONN PLUG 12POS FEMALE SOLDER HR585-ND - CONN PLUG 12POS FEMALE CRIMP HR584-ND - CONN PLUG 10POS FEMALE CRIMP |
| 其它名称： | *HR30-7P-C HR307PC HR876 |
The product information in this catalog is for reference only. Please request the Engineering Drawing for the most current and accurate design information.
All non-RoHS products have been discontinued, or will be discontinued soon. Please check the products status on the Hirose website RoHS search at www.hirose-connectors.com, or contact your Hirose sales representative.
B Assembly Procedures
Plug Assembly Sequence
Insulator/contact assembly
Push/pull locking collar
Spring
Seal bushing
Strain relief
Back shell
1
A
B
A
Cable
B
2 - -0.5 mm
Solder type : 3 and 6 pos.
Solder type : 12 pos.
Crimp type : 10 and 12 pos.
2 mm
2 mm
0
5.5 mm max.
10 mm max.
15 to 20 mm
Thread the back shell, strain relief, seal bushing, spring and push/pull locking collar over the cable as shown above.
Block end face
Insulator/contact assembly
Solder termination fixture
2
Solder type
1. Pre-solder the exposed cable conductors (dia. A). The diameter of the pre-soldered conductors should not exceed 0.7
mm for 6 contact plug and 1.0 mm for 3 contact plug.
2. Insert the insulator body over the applicable solder termination fixture.
3. Insert the pre-soldered conductors in the contact soldering pot and solder them in place.
Soldering iron temperature should be 280 ±10? applied for 3-4 second.
Crimp type
1. Crimp the applicable contact to the stripped conductor. Use correct crimp tools. Verify the dimensions and crimp
configuration.
2. Insert the contact into the appropriate opening in the insulator body.
3. Verify fully seated position by applying a slight pull force on the conductor. The contact should remain in place.
Re-insert if not seated.
10
相关PDF资料 |
PDF描述 |
|---|---|
| HR30-7R-C | CONN DUST CAP FOR 10&12POS RECPT |
| HR30-6R-C | CONN DUST CAP FOR 3&6POS RECEPT |
| NC7SP58P6X | IC GATE ULP UNIV 2-INP SC70-5 |
| GMA.2B.070.DG | STRAIN RELIEF 7.0MM DIA GRAY |
| GMA.2B.060.DN | STRAIN RELIEF 6.0MM DIA BLACK |
相关代理商/技术参数 |
参数描述 |
|---|---|
| HR30-7P-C(71) | 功能描述:环形推拉式连接器 CAP FOR PLUG SH SZ 7 RoHS:否 制造商:Hirose Connector 产品类型:Connectors 系列:HR10 触点类型:Socket (Female) 外壳类型:Receptacle 触点数量:4 外壳大小:7 安装风格:Panel 端接类型:Solder 电流额定值:2 A |
| HR30-7R-10PC | 功能描述:CONN RECEPT 10POS MALE CRIMP RoHS:否 类别:连接器，互连式 >> 圆形 - 外壳 系列:HR30 标准包装:1 系列:军用, MIL-DTL-38999 系列 III, ACT 连接器类型:母触点插座 位置数:5 外壳尺寸 - 插件:15-5 外壳尺寸，MIL:D 触点类型：:压接 触点尺寸:16 安装类型:面板安装，隔墙式（前端螺母） 紧固型:有螺纹 方向:N（正常型） 外壳材料，表面处理:合成物，草绿色镉镀层 防护等级:抗环境影响 特点:屏蔽 包装:散装 请注意:不提供触点 其它名称:DD38999/24JD5BN |
| HR30-7R-10PC(71) | 功能描述:环形推拉式连接器 10P RECP SHELL SZ 7 MALE CRIMP RoHS:否 制造商:Hirose Connector 产品类型:Connectors 系列:HR10 触点类型:Socket (Female) 外壳类型:Receptacle 触点数量:4 外壳大小:7 安装风格:Panel 端接类型:Solder 电流额定值:2 A |
| HR30-7R-12P | 制造商:Hirose 功能描述: |
| HR30-7R-12P(71) | 功能描述:环形推拉式连接器 12P RECP SHELL SZ 7 MALE TERM SOLDER RoHS:否 制造商:Hirose Connector 产品类型:Connectors 系列:HR10 触点类型:Socket (Female) 外壳类型:Receptacle 触点数量:4 外壳大小:7 安装风格:Panel 端接类型:Solder 电流额定值:2 A |
发布紧急采购，3分钟左右您将得到回复。