- 您现在的位置：买卖IC网 > PDF目录20505 > IB050Q096T70N1-CB (Vicor Corporation)1/4 BRICK IBC 36-60VIN 70A EVAL PDF资料下载
参数资料
| 型号： | IB050Q096T70N1-CB |
| 厂商： | Vicor Corporation |
| 文件页数： | 11/15页 |
| 文件大小： | 0K |
| 描述： | 1/4 BRICK IBC 36-60VIN 70A EVAL |
| 标准包装： | 1 |
| 系列： | VI BRICK™ |
| 主要目的： | DC/DC，步降 |
| 输出及类型： | 1，隔离 |
| 功率 - 输出： | 750W |
| 输出电压： | 9.6V |
| 电流 - 输出： | 70A |
| 输入电压： | 36 ~ 60V |
| 稳压器拓扑结构： | 降压 |
| 频率 - 开关： | 1MHz |
| 板类型： | 完全填充 |
| 已供物品： | 板 |
| 已用 IC / 零件： | IB050Q096T70 |
| 相关产品： | 1102-1047-ND - IBC MODULE 9.6VDC 70A 750W |
| 其它名称： | 1102-1053 |
IB050Q096T70N1-00
APPLICATIONS NOTE
pins should be bypassed with an RC damper (e.g., 47 μ F in series with
Parallel Operation
The IBC will inherently current share when operated in an array. Arrays may
be used for higher power or redundancy in an application. Current sharing
accuracy is maximized when the source and load impedance presented to
each IBC within an array are equal. The recommended method to achieve
matched impedances is to dedicate common copper planes within the PCB
to deliver and return the current to the array, rather than rely upon traces
of varying lengths. In typical applications the current being delivered to the
load is larger than that sourced from the input, allowing narrower traces to
be utilized on the input side if necessary. The use of dedicated power
planes is, however, preferable.
One or more IBCs in an array may be disabled without adversely affecting
operation or reliability as long as the load does not exceed the rated power
of the enabled IBCs.
The IBC power train and control architecture allow bi-directional power
transfer, including reverse power processing from the IBC output to its
input. The IBC’s ability to process power in reverse improves the IBC tran-
sient response to an output load dump.
Thermal Considerations
The temperature distribution of the VI Brick can vary significantly
with its input /output operating conditions, thermal management and
environmental conditions. Although the PCB is UL rated to 130°C, it is
recommended that PCB temperatures be maintained at or below 125°C.
For maximum long term reliability, lower PCB temperatures are
recommended for continuous operation, however, short periods of
operation at 125°C will not negatively impact performance or reliability.
WARNING: Thermal and voltage hazards. The IBC can operate with surface
temperatures and operating voltages that may be hazardous to personnel.
Ensure that adequate protection is in place to avoid inadvertent contact.
PART NUMBERING
Input Impedance Recommendations
To take full advantage of the IBC capabilities, the impedance presented to
its input terminals must be low from DC to approximately 5 MHz.
The source should exhibit low inductance and should have a critically
damped response. If the interconnect inductance is excessive, the IBC input
0.3 ) to retain of the IBC, the source and generally theGiven the
wide Ω bandwidth low source impedance response is operation. limiting
factor in the overall system response.
Anomalies in the response of the source will appear at the output of the
IBC multiplied by its K factor. The DC resistance of the source should be
kept as low as possible to minimize voltage deviations. This is especially
important if the IBC is operated near low or high line as the
overvoltage /undervoltage detection circuitry could be activated.
Input Fuse Recommendations
The IBC is not internally fused in order to provide flexibility in configuring
power systems. However, input line fusing of VI Bricks must always be
incorporated within the power system. A fast acting fuse should be placed
in series with the +In port. See safety agency approvals.
Application Notes
For IBC and VI Brick application notes on soldering, thermal management,
board layout, and system design visit vicorpower.com .
Product
Family
IB
Input
Voltage
050
Package
Q
Nominal
Output Voltage
096
Temperature
Grade
T
Output
Current
70
Enable
Logic
N = Negative
Pin
Length
1 = 0.145
Options
-00 = Open frame
P = Positive
2 = 0.210
3 = 0.180
-BP = Baseplate
IBC MODULE
Page 11 of 15
Rev 2.1
5/2013
vicorpower.com
800 735.6200
相关PDF资料 |
PDF描述 |
|---|---|
| TC4431EJA | IC MOSFET DRIVER 30V 1.5A 8-CDIP |
| IXDD408CI | IC MOSFET DRVR LS 8A SGL 5TO-220 |
| LXC100-1050SW | POWER SUPPLY LED 100W 1050MA |
| NTSB20U100CT-1G | DIODE SCHOTTKY 20A 100V I2PAK |
| TC428IJA | IC MOSFET DVR 1.5A DUAL HS 8CDIP |
相关代理商/技术参数 |
参数描述 |
|---|---|
| IB050Q096T80N1-BP | 制造商:VICOR 制造商全称:Vicor Corporation 功能描述:5:1 Intermediate Bus Converter Module: Up to 850 W Output |
| IB050Q096T80N1-OO | 制造商:VICOR 制造商全称:Vicor Corporation 功能描述:5:1 Intermediate Bus Converter Module: Up to 850 W Output |
| IB050Q096T80N2-BP | 制造商:VICOR 制造商全称:Vicor Corporation 功能描述:5:1 Intermediate Bus Converter Module: Up to 850 W Output |
| IB050Q096T80N2-OO | 制造商:VICOR 制造商全称:Vicor Corporation 功能描述:5:1 Intermediate Bus Converter Module: Up to 850 W Output |
| IB050Q096T80N3-BP | 制造商:VICOR 制造商全称:Vicor Corporation 功能描述:5:1 Intermediate Bus Converter Module: Up to 850 W Output |
发布紧急采购，3分钟左右您将得到回复。