参数资料
| 型号： | ICL3226IAZ |
| 厂商： | Intersil |
| 文件页数： | 4/18页 |
| 文件大小： | 0K |
| 描述： | IC 1DRVR/1RCVR RS232 3V 16-SSOP |
| 标准包装： | 385 |
| 类型： | 收发器 |
| 驱动器/接收器数： | 1/1 |
| 规程： | RS232 |
| 电源电压： | 3 V ~ 5.5 V |
| 安装类型： | 表面贴装 |
| 封装/外壳： | 16-SSOP（0.209"，5.30mm 宽） |
| 供应商设备封装： | 16-SSOP |
| 包装： | 管件 |
12
FN4876.10
March 1, 2006
transition occurs on a receiver or transmitter input (see
Figure 7). For immediate power up when the cable is
reattached, connect FORCEON to FORCEOFF through a
network similar to that shown in Figure 5.
Ready Output (ICL3224 and ICL3226 only)
The Ready output indicates that the ICL322X is ready to
transmit. Ready switches low whenever the device enters
powerdown, and switches back high during power-up when
V- reaches -4V or lower.
Capacitor Selection
The charge pumps require 0.1
F capacitors for 3.3V
operation. For other supply voltages refer to Table 3 for
capacitor values. Do not use values smaller than those listed
in Table 3. Increasing the capacitor values (by a factor of 2)
reduces ripple on the transmitter outputs and slightly
reduces power consumption. C2, C3, and C4 can be
increased without increasing C1’s value, however, do not
increase C1 without also increasing C2, C3, and C4 to
maintain the proper ratios (C1 to the other capacitors).
When using minimum required capacitor values, make sure
that capacitor values do not degrade excessively with
temperature. If in doubt, use capacitors with a larger nominal
value. The capacitor’s equivalent series resistance (ESR)
usually rises at low temperatures and it influences the
amount of ripple on V+ and V-.
Power Supply Decoupling
In most circumstances a 0.1
F bypass capacitor is
adequate. In applications that are particularly sensitive to
power supply noise, decouple VCC to ground with a
capacitor of the same value as the charge-pump capacitor C1.
Connect the bypass capacitor as close as possible to the IC.
Transmitter Outputs when Exiting
Powerdown
Figure 10 shows the response of two transmitter outputs
when exiting powerdown mode. As they activate, the two
transmitter outputs properly go to opposite RS-232 levels,
with no glitching, ringing, nor undesirable transients. Each
transmitter is loaded with 3k
in parallel with 2500pF. Note
that the transmitters enable only when the magnitude of the
supplies exceed approximately 3V.
Operation Down to 2.7V
ICL32XX transmitter outputs meet RS-562 levels (±3.7V), at
the full data rate, with VCC as low as 2.7V. RS-562 levels
typically ensure interoperability with RS-232 devices.
Mouse Driveability
The ICL3244 is specifically designed to power a serial
mouse while operating from low voltage supplies. Figure 11
shows the transmitter output voltages under increasing load
current. The on-chip switching regulator ensures the
transmitters will supply at least ±5V during worst case
conditions (15mA for paralleled V+ transmitters, 7.3mA for
single V- transmitter).
High Data Rates
The ICL32XX maintain the RS-232 ±5V minimum transmitter
output voltages even at high data rates. Figure 12 details a
transmitter loopback test circuit, and Figure 13 illustrates the
loopback test result at 120kbps. For this test, all transmitters
were simultaneously driving RS-232 loads in parallel with
TABLE 3. REQUIRED CAPACITOR VALUES (Note 8)
VCC (V)
C1 (F)
C2, C3, C4 (F)
3.0 to 3.6 (3.3V
±10%)
0.1 (0.22)
3.15 to 3.6 (3.3V
±5%)
(0.1)
4.5 to 5.5
0.047
0.33
3.0 to 5.5
0.1 (0.22)
0.47 (1.0)
NOTE:
7. Parenthesized values apply only to the ICL3238
TIME (20
s/DIV.)
T1
T2
2V/DIV
5V/DIV
VCC = +3.3V
FORCEOFF
FIGURE 10. TRANSMITTER OUTPUTS WHEN EXITING
POWERDOWN
C1 - C4 = 0.1
F
5V/DIV
READY
FIGURE 11. TRANSMITTER OUTPUT VOLTAGE vs LOAD
CURRENT (PER TRANSMITTER, i.e., DOUBLE
CURRENT AXIS FOR TOTAL VOUT+ CURRENT)
T
RANSMITTER
OUTPUT
V
O
LTAGE
(V)
LOAD CURRENT PER TRANSMITTER (mA)
02
468
10
-6
-4
-2
0
2
4
6
-5
-3
-1
1
3
5
1
3579
VOUT+
VOUT -
VCC
VOUT+
VOUT -
T1
T2
T3
VCC = 3.0V
ICL3244
ICL3224, ICL3226, ICL3238, ICL3244
相关PDF资料 |
PDF描述 |
|---|---|
| VI-BW1-MW-F3 | CONVERTER MOD DC/DC 12V 100W |
| ICL3223CPZ | IC 2DRVR/2RCVR RS232 3V 20-PDIP |
| MAX1083AEUE+T | IC ADC 10BIT 300KSPS 16-TSSOP |
| IDT723666L15PF | IC FIFO SYNC 8192X36 128QFP |
| MAX1082AEUE+T | IC ADC 10BIT 400KSPS 16-TSSOP |
相关代理商/技术参数 |
参数描述 |
|---|---|
| ICL3226IAZ-T | 功能描述:RS-232接口集成电路 RS232 3V 1D/1R E-DWN INDEL RoHS:否 制造商:Exar 数据速率:52 Mbps 工作电源电压:5 V 电源电流:300 mA 工作温度范围:- 40 C to + 85 C 安装风格:SMD/SMT 封装 / 箱体:LQFP-100 封装: |
| ICL3227 | 制造商:INTERSIL 制造商全称:Intersil Corporation 功能描述:1 Microamp, +3V to +5.5V, 1Mbps, RS-232 Transceivers with Enhanced Automatic Powerdown |
| ICL3227 WAF | 制造商:Intersil Corporation 功能描述: |
| ICL3227CA | 制造商:Rochester Electronics LLC 功能描述:RS232 3V 1D/1R 1MBPS E-DWN 16SSOP COM - Bulk |
| ICL3227E | 制造商:INTERSIL 制造商全称:Intersil Corporation 功能描述:+-15kV ESD Protected, +3V to +5.5V, 1Microamp, 1Mbps, RS-232 Transceivers with Enhanced Automatic Powerdown |
发布紧急采购，3分钟左右您将得到回复。