- 您现在的位置：买卖IC网 > PDF目录1806 > ICL7665ACPA (Maxim Integrated Products)IC VOLT DETEC DUAL OVR/UND 8-DIP PDF资料下载
参数资料
| 型号： | ICL7665ACPA |
| 厂商： | Maxim Integrated Products |
| 文件页数： | 9/12页 |
| 文件大小： | 0K |
| 描述： | IC VOLT DETEC DUAL OVR/UND 8-DIP |
| 产品培训模块： | Lead (SnPb) Finish for COTS Obsolescence Mitigation Program |
| 标准包装： | 50 |
| 类型： | 多压监控器 |
| 监视电压数目： | 2 |
| 输出： | 开路漏极或开路集电极 |
| 复位： | 高有效 |
| 复位超时： | 最小 <1 ms |
| 电压 - 阀值： | 可调节/可选择 |
| 工作温度： | 0°C ~ 70°C |
| 安装类型： | 通孔 |
| 封装/外壳： | 8-DIP（0.300"，7.62mm） |
| 供应商设备封装： | 8-PDIP |
| 包装： | 管件 |
Microprocessor Voltage Monitor with
Dual Over/Undervoltage Detection
Combination Low-Battery Warning and
Low-Battery Disconnect
Nickel cadmium (NiCd) batteries are excellent recharge-
able power sources for portable equipment, but care
must be taken to ensure that NiCd batteries are not
damaged by overdischarge. Specifically, a NiCd battery
should not be discharged to the point where the polarity
of the lowest-capacity cell is reversed, and that cell is
reverse charged by the higher-capacity cells. This reverse
charging will dramatically reduce the life of a NiCd battery.
The Figure 8 circuit both prevents reverse charging and
gives a low-battery warning. A typical low-battery warning
voltage is 1V per cell. Since a NiCd “9V” battery is ordi-
narily made up of six cells with a nominal voltage of 7.2V,
a low-battery warning of 6V is appropriate, with a small
hysteresis of 100mV. To prevent overdischarge of a bat-
tery, the load should be disconnected when the battery
voltage is 1V x (N – 1), where N = number of cells. In this
case, the low-battery load disconnect should occur at
5V. Since the battery voltage will rise when the load is
disconnected, 800mV of hysteresis is used to prevent
repeated on/off cycling.
Power-Fail Warning and
Power-Up/Power-Down Reset
Figure 9 illustrates a power-fail warning circuit that
monitors raw DC input voltage to the 7805 three-termi-
nal 5V regulator. The power-fail warning signal goes
high when the unregulated DC input falls below 8.0V.
When the raw DC power source is disconnected or the
AC power fails, the voltage on the input of the 7805
decays at a rate of I OUT / C (in this case, 200mV/ms).
Since the 7805 will continue to provide a 5V output at
1A until V IN is less than 7.3V, this circuit will give at
least 3.5ms of warning before the 5V output begins to
drop. If additional warning time is needed, either the
trip voltage or filter capacitance should be increased,
or the output current should be decreased.
The ICL7665 OUT2 is set to trip when the 5V output has
decayed to 3.9V. This output can be used to prevent
the microprocessor from writing spurious data to a
CMOS battery-backup memory, or can be used to acti-
vate a battery-backup system.
AC Power-Fail and Brownout Detector
By monitoring the secondary of the transformer, the cir-
cuit in Figure 10 performs the same power-failure warn-
ing function as Figure 9. With a normal 110V AC input
to the transformer, OUT1 will discharge C1 every
16.7ms when the peak transformer secondary voltage
exceeds 10.2V. When the 110V AC power-line voltage
is either interrupted or reduced so that the peak voltage
is less than 10.2V, C1 will be charged through R1.
OUT2, the power-fail warning output, goes high when
the voltage on C1 reaches 1.3V. The time constant R1 x
C1 determines the delay time before the power-fail warning
signal is activated, in this case 42ms or 2 1 ? 2 line cycles.
Optional components R2, R3 and Q1 add hysteresis by
increasing the peak secondary voltage required to dis-
charge C1 once the power-fail warning is active.
Battery Switchover Circuit
The circuit in Figure 11 performs two functions: switch-
ing the power supply of a CMOS memory to a backup
battery when the line-powered supply is turned off, and
lighting a low-battery-warning LED when the backup
battery is nearly discharged. The PNP transistor, Q1,
connects the line-powered +5V to the CMOS memory
whenever the line-powered +5V supply voltage is
greater than 3.5V. The voltage drop across Q1 will only
be a couple of hundred millivolts, since it will be satu-
rated. Whenever the input voltage falls below 3.5V,
OUT1 goes high, turns off Q1, and connects the 3V
lithium cell to the CMOS memory.
The second voltage detector of the ICL7665 monitors the
voltage of the lithium cell. If the battery voltage falls below
2.6V, OUT2 goes low and the low-battery-warning LED
turns on (assuming that the +5V is present, of course).
Another possible use for the second section of the
ICL7665 is the detection of the input voltage falling
below 4.5V. This signal could then be used to prevent
the microprocessor from writing spurious data to the
CMOS memory while its power-supply voltage is out-
side its guaranteed operating range.
Simple High/Low Temperature Alarm
The circuit in Figure 12 is a simple high/low tempera-
ture alarm, which uses a low-cost NPN transistor as the
sensor and an ICL7665 as the high/low detector. The
NPN transistor and potentiometer R1 form a Vbe multi-
plier whose output voltage is determined by the Vbe of
the transistor and the position of R1’s wiper arm. The
voltage at the top of R1 will have a temperature coeffi-
cient of approximately -5mV/°C. R1 is set so that the
voltage at V SET2 equals the V SET2 trip voltage when the
temperature of the NPN transistor reaches the level
selected for the high-temperature alarm. R2 can be
adjusted so that the voltage at V SET1 is 1.3V when the
NPN transistor’s temperature reaches the low-tempera-
ture limit.
_______________________________________________________________________________________
9
相关PDF资料 |
PDF描述 |
|---|---|
| ICL7665SIBA | IC VOLT DETECTOR OVER/UND 8-SOIC |
| ICL7673CBA-T | IC SWITCH BATTERY BACKUP 8-SOIC |
| ICL8069DESA | IC VREF SHUNT 1.23V 8-SOIC |
| ICM7211AMIPL | IC LCD DISPLAY DRVR 4DGT 40-DIP |
| ICM7212AMIQH-D | IC DECODR/DVR LED 4DIGIT 44PLCC |
相关代理商/技术参数 |
参数描述 |
|---|---|
| ICL7665ACPA+ | 功能描述:电压监测器/监控器 uP V Monitor w/Dual Over/Under V Detect RoHS:否 制造商:Texas Instruments 监测电压数:2 监测电压:Adjustable 输出类型:Open Drain 欠电压阈值: 过电压阈值: 准确性:1 % 工作电源电压:1.5 V to 6.5 V 工作电源电流:1.8 uA 最大工作温度:+ 125 C 封装 / 箱体:SON-6 安装风格:SMD/SMT |
| ICL7665ACPA-2 | 制造商:Rochester Electronics LLC 功能描述: 制造商:Maxim Integrated Products 功能描述: |
| ICL7665ACSA | 功能描述:电压监测器/监控器 Integrated Circuits (ICs) RoHS:否 制造商:Texas Instruments 监测电压数:2 监测电压:Adjustable 输出类型:Open Drain 欠电压阈值: 过电压阈值: 准确性:1 % 工作电源电压:1.5 V to 6.5 V 工作电源电流:1.8 uA 最大工作温度:+ 125 C 封装 / 箱体:SON-6 安装风格:SMD/SMT |
| ICL7665ACSA+ | 功能描述:电压监测器/监控器 uP V Monitor w/Dual Over/Under V Detect RoHS:否 制造商:Texas Instruments 监测电压数:2 监测电压:Adjustable 输出类型:Open Drain 欠电压阈值: 过电压阈值: 准确性:1 % 工作电源电压:1.5 V to 6.5 V 工作电源电流:1.8 uA 最大工作温度:+ 125 C 封装 / 箱体:SON-6 安装风格:SMD/SMT |
| ICL7665ACSA+T | 功能描述:电压监测器/监控器 uP V Monitor w/Dual Over/Under V Detect RoHS:否 制造商:Texas Instruments 监测电压数:2 监测电压:Adjustable 输出类型:Open Drain 欠电压阈值: 过电压阈值: 准确性:1 % 工作电源电压:1.5 V to 6.5 V 工作电源电流:1.8 uA 最大工作温度:+ 125 C 封装 / 箱体:SON-6 安装风格:SMD/SMT |
发布紧急采购，3分钟左右您将得到回复。