- 您现在的位置：买卖IC网 > PDF目录20178 > ICM7228BIBIZ (Intersil)IC LED DISPLAY DRVR 8DGT 28-SOIC PDF资料下载
参数资料
| 型号： | ICM7228BIBIZ |
| 厂商： | Intersil |
| 文件页数： | 11/18页 |
| 文件大小： | 0K |
| 描述： | IC LED DISPLAY DRVR 8DGT 28-SOIC |
| 标准包装： | 260 |
| 显示器类型： | LED |
| 配置： | 7 段显示 |
| 数字或字符： | 8 位数字 |
| 电流 - 电源： | 250µA |
| 电源电压： | 4 V ~ 6 V |
| 工作温度： | -40°C ~ 85°C |
| 安装类型： | 表面贴装 |
| 封装/外壳： | 28-SOIC（0.295"，7.50mm 宽） |
| 供应商设备封装： | 28-SOIC W |
| 包装： | 管件 |
ICM7228
Sequential 8-Digit Update
The logic state of DATA COMING (lD7) is also latched
during a Control Register update. If the latched value of
DATA COMING (lD7) is high, the display becomes blanked
and a sequential 8-digit update is initiated. Display data can
now be written into RAM with 8 successive WRITE pulses,
starting with digit 1 and ending with digit 8 (See Figure 2).
After all 8 RAM locations have been written to, the display
turns on again and the new data is displayed. Additional
write pulses are ignored until a new Control Register update
is performed. All 8 digits are displayed in the format
(Hex/Code B or No Decode) specified by the control word
that preceded the 8 digit update. If a decoding scheme
(Hex/Code B) is to be used, the value of lD3 during the
control word update determines which RAM bank will be
written to.
Single Digit Update
In this mode each digit data in the display RAM can be updated
individually without changing the other display data. First, with
MODE input high, a control word is written to the Control
Register carrying the following information; DATA COMING
(lD7) low, the desired display format data on lD4 - lD6, the RAM
bank selected by lD3 (if decoding is selected) and the address
of the digit to be updated on data lines lD0 - lD2 (See Table 4).
A second write to the ICM7228A/B, this time with MODE input
low, transfers the data at the lD0 - lD7 inputs into the selected
digit’s RAM location. In single digit update mode, each
individual digit’s data can be specified independently for being
displayed in Decoded or No-Decode mode. For those digits
which decoding scheme (Hex/Code B) is selected, only one
can be effective at a time. Whenever a control word is written,
the specified decoding scheme will be applied to all those digits
which selected to be displayed in Decoded mode.
DATA BUS D0-D7
ID0
D0 - D7
I/O OR
ID7
INTERSIL
MEMORY
ICM7228A/B
LED DISPLAY
WRITE PULSE
DECODER
ENABLE
DEVICE SELECT
AND
WRITE PULSE
SEGMENTS
DRIVE
WRITE
ADDRESS
A1-A15
DECODER
A0
MODE
DIGITS
DRIVE
ADDRESS BUS A0 - A15
FIGURE 9. ICM7228A/B MICROPROCESSOR SYSTEM INTERFACING
TABLE 4. DIGITS ADDRESS, ICM7228A/B
setup and 0ns hold time with a 200ns minimum WRITE pulse.
1D2
0
0
0
0
1
1
1
1
INPUT DATA LINES
lD2
0
0
1
1
0
0
1
1
lD0
0
1
0
1
0
1
0
1
SELECTED DIGIT
DlGlT 1
DlGlT 2
DIGlT 3
DlGlT 4
DIGIT 5
DlGlT 6
DlGlT 7
DlGlT 8
Input logic levels are TTL and CMOS compatible. Figure 10
shows a generic method of driving the ICM7228C from a
microprocessor bus. To the microprocessor, the 8 bytes of the
Display RAM appear to be 8 separate I/O locations. Loading
the ICM7228C is quite similar to a standard memory write
cycle. The address of the digit to be updated is placed on lines
DA0 - DA2, the data to be written is placed on lines ID0 - lD3
and ID7, then a low pulse on WRITE input will transfer the
data in. See Figure 3 and Switching Characteristics Table for
write cycle timing parameters.
The ICM7228C does not have any control register, and also
does not provide the No Decode display format. Hexadecimal
System Interfacing, ICM7228C
The ICM7228C is directly compatible with the architecture of
most microprocessor systems. Its fast switching
characteristics make it possible to access them as a memory
mapped I/O device with no wait state necessary in most
microcontroller systems. All the ICM7228C inputs, excluding
HEXA/CODE B/SHUTDOWN, feature a 250ns minimum
11
or Code B character selection and shutdown mode are directly
controlled through the three level input at Pin 9, which is
accordingly called HEXA/CODE B/SHUTDOWN. See Table 3
for input and output definitions of the ICM7228C.
相关PDF资料 |
PDF描述 |
|---|---|
| MLF2012C330K | INDUCTOR MULTILAYER 33UH 0805 |
| PSAA30R-120-R-CR3 | ADAPTER WALL R-SERIES 30W 12V |
| VI-J6H-CX-B1 | CONVERTER MOD DC/DC 52V 75W |
| T95R337K004LZAL | CAP TANT 330UF 4V 10% 2824 |
| MLF2012A2R7K | INDUCTOR MULTILAYER 2.7UH 0805 |
相关代理商/技术参数 |
参数描述 |
|---|---|
| ICM7228BIJI | 制造商:Maxim Integrated Products 功能描述:8 DIGIT LED DISPLAY DRIVER - Rail/Tube 制造商:Rochester Electronics LLC 功能描述:- Bulk |
| ICM7228BIPI | 功能描述:LED显示驱动器 DISPLAY 8 DIG LED DRIVER 28CDIP IND RoHS:否 制造商:Micrel 数位数量:5 片段数量: 安装风格:SMD/SMT 封装 / 箱体:PLCC-44 工作电源电压:4.75 V to 11 V 最大电源电流:10 mA 最大工作温度:+ 85 C 最小工作温度:- 40 C 封装:Tube |
| ICM7228BIPI WAF | 制造商:Harris Corporation 功能描述: |
| ICM7228BIPIZ | 功能描述:LED显示驱动器 W/ANNEAL DISPLAY 8 DIG LED DRVR IND RoHS:否 制造商:Micrel 数位数量:5 片段数量: 安装风格:SMD/SMT 封装 / 箱体:PLCC-44 工作电源电压:4.75 V to 11 V 最大电源电流:10 mA 最大工作温度:+ 85 C 最小工作温度:- 40 C 封装:Tube |
| ICM7228BMJ/883B WAF | 制造商:Harris Corporation 功能描述: |
发布紧急采购，3分钟左右您将得到回复。