- 您现在的位置：买卖IC网 > PDF目录8953 > ICS1574BMLF (IDT, Integrated Device Technology Inc)IC CLOCK GEN PROGR LASER 16-SOIC PDF资料下载
参数资料
| 型号： | ICS1574BMLF |
| 厂商： | IDT, Integrated Device Technology Inc |
| 文件页数： | 8/12页 |
| 文件大小： | 0K |
| 描述： | IC CLOCK GEN PROGR LASER 16-SOIC |
| 标准包装： | 48 |
| 类型： | 时钟/频率合成器，时钟发生器 |
| PLL： | 是 |
| 输入： | 时钟，晶体 |
| 输出： | CMOS |
| 电路数： | 1 |
| 比率 - 输入:输出： | 1:1 |
| 差分 - 输入:输出： | 无/无 |
| 频率 - 最大： | 400MHz |
| 除法器/乘法器： | 是/无 |
| 电源电压： | 4.75 V ~ 5.25 V |
| 工作温度： | 0°C ~ 70°C |
| 安装类型： | 表面贴装 |
| 封装/外壳： | 16-SOIC（0.154"，3.90mm 宽） |
| 供应商设备封装： | 16-SOIC |
| 包装： | 管件 |
| 其它名称： | 1574BMLF |
5
ICS1574B
N
I
A
G
O
C
VY
C
N
E
U
Q
E
R
F
X
A
M
4z
H
M
0
1
5z
H
M
0
2
6z
H
M
0
3
7z
H
M
0
4
Reference Oscillator
and Crystal Selection
The ICS1574B has circuitry on-board to implement a
Pierce oscillator with the addition of only one external
component, a quartz crystal. Pierce oscillators operate the
crystal
in
anti- (also called parallel-) resonant mode. See the AC
Characteristics for the effective capacitive loading to
specify when ordering crystals.
Series-resonant crystals may also be used with the
ICS1574B. Be aware that the oscillation frequency will be
slightly higher than the frequency that is stamped on the
can (typically 0.025 – 0.05%).
As the entire operation of the phase-locked loop depends
on having a stable reference frequency, we recommend
that the crystal be mounted as closely as possible to the
package. Avoid routing digital signals or the ICS1574B
outputs underneath or near these traces. It is also desirable
to ground the crystal can to the ground plane, if possible.
If an external reference frequency source is to be used with
the ICS1574B, it is important that it be jitter-free. The ris-
ing and falling edges of that signal should be fast and free
of noise for best results.
The loop phase can be locked to either the rising or falling
edges of the XTAL1 input signals, and is controlled by
Bit 56.
Power-On Initialization
The ICS1574B has an internal power-on reset circuit that
performs the following functions:
1) Selects the modulus of the PCLK divider to
be four (4).
2) Sets the multiplexer to pass the reference
frequency to PCLK divider input.
These functions should allow initialization for most appli-
cations that cannot immediately provide for register
programming upon system power-up.
Because the power-on reset circuit is on the VDD supply,
and because that supply is filtered, care must be taken to
allow the reset to de-assert before programming. A safe
guideline is to allow 20 microseconds after the VDD sup-
ply reaches 4 volts.
Programming Notes
VCO Frequency Range: Use the post-divider to keep the
VCO frequency as high as possible within its operating
range.
Divider Range: For best results in normal situations
keep the reference divider modulus as short as possible
(for a frequency at the output of the reference divider in
the few hundred kHz to several MHz range). If you
need to go to a lower phase comparator reference fre-
quency (usually required for increased frequency
accuracy), that is acceptable, but jitter performance will
suffer somewhat.
VCO Gain Programming: Use the minimum gain which
can reliably achieve the VCO frequency desired, as
shown here:
Phase Detector Gain: For most applications and divider
ranges, set P [1, 0] = 10 and set P [2] = 1. Under some
circumstances, setting the P [2] bit “on” can reduce
jitter. During operation at exact multiples of the crystal
frequency, P[2] bit = 0 may provide the best jitter per-
formance.
Board Test Support
It is often desirable to statically control the levels of the
output pins for circuit board test. The ICS1574B supports
this through a register programmable mode, AUX-EN.
When this mode is set, a register bit directly controls the
logic level of the PCLK pin. This mode is activated when
the S[0] and S[1] bits are both set to logic 1. See Register
Mapping for details.
相关PDF资料 |
PDF描述 |
|---|---|
| D38999/26KD19PD | CONN PLUG 19POS STRAIGHT W/PINS |
| ICS1562BM-201-4LF | IC VIDEO CLK SYNTHESIZER 16-SOIC |
| VE-20J-MY-F2 | CONVERTER MOD DC/DC 36V 50W |
| MS3126F24-61PZ | CONN PLUG 61POS STRAIGHT W/PINS |
| VE-JVJ-MZ-F2 | CONVERTER MOD DC/DC 36V 25W |
相关代理商/技术参数 |
参数描述 |
|---|---|
| ICS1574BMLFT | 功能描述:IC CLOCK GEN PROGR LASER 16-SOIC RoHS:是 类别:集成电路 (IC) >> 时钟/计时 - 时钟发生器，PLL，频率合成器 系列:- 标准包装:27 系列:Precision Edge® 类型:频率合成器 PLL:是 输入:PECL，晶体 输出:PECL 电路数:1 比率 - 输入:输出:1:1 差分 - 输入:输出:无/是 频率 - 最大:800MHz 除法器/乘法器:是/无 电源电压:3.135 V ~ 5.25 V 工作温度:0°C ~ 85°C 安装类型:表面贴装 封装/外壳:28-SOIC（0.295"，7.50mm 宽） 供应商设备封装:28-SOIC 包装:管件 |
| ICS1574BMT | 功能描述:IC CLOCK GEN PROGR LASER 16-SOIC RoHS:否 类别:集成电路 (IC) >> 时钟/计时 - 时钟发生器，PLL，频率合成器 系列:- 产品变化通告:Product Discontinuation 04/May/2011 标准包装:96 系列:- 类型:时钟倍频器，零延迟缓冲器 PLL:带旁路 输入:LVTTL 输出:LVTTL 电路数:1 比率 - 输入:输出:1:8 差分 - 输入:输出:无/无 频率 - 最大:133.3MHz 除法器/乘法器:是/无 电源电压:3 V ~ 3.6 V 工作温度:0°C ~ 70°C 安装类型:表面贴装 封装/外壳:16-TSSOP（0.173"，4.40mm 宽） 供应商设备封装:16-TSSOP 包装:管件 其它名称:23S08-5HPGG |
| ICS1577N | 制造商:未知厂家 制造商全称:未知厂家 功能描述:Analog IC |
| ICS-16 | 制造商:MAXCONN 功能描述: |
| ICS162834 | 制造商:ICS 制造商全称:ICS 功能描述:18-Bit 3.3V Registered Buffer |
发布紧急采购，3分钟左右您将得到回复。