- 您现在的位置：买卖IC网 > PDF目录9027 > ICS276PGLFT (IDT, Integrated Device Technology Inc)VCXO CLK SYNTH TRPL PLL 16-TSSOP PDF资料下载
参数资料
| 型号： | ICS276PGLFT |
| 厂商： | IDT, Integrated Device Technology Inc |
| 文件页数： | 5/10页 |
| 文件大小： | 0K |
| 描述： | VCXO CLK SYNTH TRPL PLL 16-TSSOP |
| 标准包装： | 2,500 |
| 系列： | VersaClock™ |
| 类型： | 时钟/频率合成器，扇出缓冲器（分配） |
| PLL： | 带旁路 |
| 输入： | 晶体 |
| 输出： | CMOS |
| 电路数： | 1 |
| 比率 - 输入:输出： | 1:3 |
| 差分 - 输入:输出： | 无/无 |
| 频率 - 最大： | 200MHz |
| 除法器/乘法器： | 是/是 |
| 电源电压： | 3.135 V ~ 3.465 V |
| 工作温度： | 0°C ~ 70°C |
| 安装类型： | 表面贴装 |
| 封装/外壳： | 16-TSSOP（0.173"，4.40mm 宽） |
| 供应商设备封装： | 16-TSSOP |
| 包装： | 带卷 (TR) |
| 其它名称： | 276PGLFT |
ICS276
TRIPLE PLL FIELD PROGRAMMABLE VCXO CLOCK SYNTHESIZER
EPROM AND VCXO SYNTHESIZER
IDT / ICS TRIPLE PLL FIELD PROGRAMMABLE VCXO CLOCK SYNTHESIZER 4
ICS276
REV E 051310
errorxtal =actual initial accuracy (in ppm) of the crystal being
measured
If the centering error is less than ±25 ppm, no adjustment is
needed. If the centering error is more than 25 ppm negative,
the PC board has excessive stray capacitance and a new
PCB layout should be considered to reduce stray
capacitance. (Alternately, the crystal may be re-specified to
a higher load capacitance. Contact IDT for details.) If the
centering error is more than 25 ppm positive, add identical
fixed centering capacitors from each crystal pin to ground.
The value for each of these caps (in pF) is given by: External
Capacitor = 2 x (centering error)/(trim sensitivity)
Trim sensitivity is a parameter which can be supplied by your
crystal vendor. If you do not know the value, assume it is 30
ppm/pF. After any changes, repeat the measurement to
verify that the remaining error is acceptably low (typically
less than ±25 ppm).
ICS276 Configuration Capabilities
The architecture of the ICS276 allows the user to easily
configure the device to a wide range of output frequencies,
for a given input reference frequency.
The frequency multiplier PLL provides a high degree of
precision. The M/N values (the multiplier/divide values
available to generate the target VCO frequency) can be set
within the range of M = 1 to 1024 and N = 1 to 32,895.
The ICS276 also provides separate output divide values,
from 2 through 63, to allow the two output clock banks to
support widely differing frequency values from the same
PLL.
Each output frequency can be represented as:
Output Drive Control
The ICS276 has two output drive settings. For VDDO=VDD,
low drive should be selected when outputs are less than 100
MHz. High drive should be selected when outputs are
greater than 100 MHz.
For VDDO<2.8V, high drive should be selected for all output
frequencies.
(Consult the AC Electrical Characteristics for output rise and
fall times for each drive option.)
IDT VersaClock Software
IDT applies years of PLL optimization experience into a user
friendly software that accepts the user’s target reference
clock and output frequencies and generates the lowest jitter,
lowest power configuration, with only a press of a button.
The user does not need to have prior PLL experience or
determine the optimal VCO frequency to support multiple
output frequencies.
VersaClock software quickly evaluates accessible VCO
frequencies with available output divide values and provides
an easy to understand, bar code rating for the target output
frequencies. The user may evaluate output accuracy,
performance trade-off scenarios in seconds.
Absolute Maximum Ratings
Stresses above the ratings listed below can cause permanent damage to the ICS276. These ratings, which are
standard values for IDT commercially rated parts, are stress ratings only. Functional operation of the device at these
or any other conditions above those indicated in the operational sections of the specifications is not implied.
Exposure to absolute maximum rating conditions for extended periods can affect product reliability. Electrical
parameters are guaranteed only over the recommended operating temperature range.
OutputFreq
REFFreq
M
N
-----
=
Parameter
Condition
Min.
Typ.
Max.
Units
Supply Voltage, VDD
Referenced to GND
7
V
Inputs
Referenced to GND
-0.5
VDD+0.5
V
Clock Outputs
Referenced to GND
-0.5
VDD+0.5
V
相关PDF资料 |
PDF描述 |
|---|---|
| VE-23N-MW-F3 | CONVERTER MOD DC/DC 18.5V 100W |
| VI-24N-MY-F3 | CONVERTER MOD DC/DC 18.5V 50W |
| ICS601M-01ILFT | IC CLK MULT LOW PH/NOISE 16SOIC |
| VE-23N-MW-F2 | CONVERTER MOD DC/DC 18.5V 100W |
| MS3450L28-22PX | CONN RCPT 6POS WALL MNT W/PINS |
相关代理商/技术参数 |
参数描述 |
|---|---|
| ICS276PGT | 功能描述:VCXO CLK SYNTH TRPL PLL 16-TSSOP RoHS:否 类别:集成电路 (IC) >> 时钟/计时 - 时钟发生器，PLL，频率合成器 系列:VersaClock™ 产品变化通告:Product Discontinuation 04/May/2011 标准包装:96 系列:- 类型:时钟倍频器，零延迟缓冲器 PLL:带旁路 输入:LVTTL 输出:LVTTL 电路数:1 比率 - 输入:输出:1:8 差分 - 输入:输出:无/无 频率 - 最大:133.3MHz 除法器/乘法器:是/无 电源电压:3 V ~ 3.6 V 工作温度:0°C ~ 70°C 安装类型:表面贴装 封装/外壳:16-TSSOP（0.173"，4.40mm 宽） 供应商设备封装:16-TSSOP 包装:管件 其它名称:23S08-5HPGG |
| ICS280 | 制造商:ICSI 制造商全称:Integrated Circuit Solution Inc 功能描述:Package Outline and Package Dimensions (16-pin TSSOP,173 Mil. Body) |
| ICS280PG | 功能描述:IC CLK SYNTH TRPL PLL 16-TSSOP RoHS:否 类别:集成电路 (IC) >> 时钟/计时 - 时钟发生器，PLL，频率合成器 系列:VersaClock™ 产品变化通告:Product Discontinuation 04/May/2011 标准包装:96 系列:- 类型:时钟倍频器，零延迟缓冲器 PLL:带旁路 输入:LVTTL 输出:LVTTL 电路数:1 比率 - 输入:输出:1:8 差分 - 输入:输出:无/无 频率 - 最大:133.3MHz 除法器/乘法器:是/无 电源电压:3 V ~ 3.6 V 工作温度:0°C ~ 70°C 安装类型:表面贴装 封装/外壳:16-TSSOP（0.173"，4.40mm 宽） 供应商设备封装:16-TSSOP 包装:管件 其它名称:23S08-5HPGG |
| ICS280PGI | 功能描述:IC CLK SYNTH TRPL PLL 16-TSSOP RoHS:否 类别:集成电路 (IC) >> 时钟/计时 - 时钟发生器，PLL，频率合成器 系列:VersaClock™ 产品变化通告:Product Discontinuation 04/May/2011 标准包装:96 系列:- 类型:时钟倍频器，零延迟缓冲器 PLL:带旁路 输入:LVTTL 输出:LVTTL 电路数:1 比率 - 输入:输出:1:8 差分 - 输入:输出:无/无 频率 - 最大:133.3MHz 除法器/乘法器:是/无 电源电压:3 V ~ 3.6 V 工作温度:0°C ~ 70°C 安装类型:表面贴装 封装/外壳:16-TSSOP（0.173"，4.40mm 宽） 供应商设备封装:16-TSSOP 包装:管件 其它名称:23S08-5HPGG |
| ICS280PGILF | 功能描述:IC CLK SYNTH TRPL PLL 16-TSSOP RoHS:是 类别:集成电路 (IC) >> 时钟/计时 - 时钟发生器，PLL，频率合成器 系列:VersaClock™ 标准包装:1,000 系列:- 类型:时钟/频率合成器，扇出分配 PLL:- 输入:- 输出:- 电路数:- 比率 - 输入:输出:- 差分 - 输入:输出:- 频率 - 最大:- 除法器/乘法器:- 电源电压:- 工作温度:- 安装类型:表面贴装 封装/外壳:56-VFQFN 裸露焊盘 供应商设备封装:56-VFQFP-EP（8x8） 包装:带卷 (TR) 其它名称:844S012AKI-01LFT |
发布紧急采购，3分钟左右您将得到回复。