参数资料
型号: ICS503MLF
厂商: IDT, Integrated Device Technology Inc
文件页数: 4/7页
文件大小: 0K
描述: IC PLL CLK MULTIPLIER 8-SOIC
标准包装: 97
系列: LOCO™
类型: 时钟发生器
PLL:
输入: 时钟,晶体
输出: CMOS
电路数: 1
比率 - 输入:输出: 1:1
差分 - 输入:输出: 无/无
频率 - 最大: 160MHz
除法器/乘法器: 无/是
电源电压: 3 V ~ 5.5 V
工作温度: 0°C ~ 70°C
安装类型: 表面贴装
封装/外壳: 8-SOIC(0.154",3.90mm 宽)
供应商设备封装: 8-SOIC
包装: 管件
其它名称: 503MLF
ICS503
LOCO PLL CLOCK MULTIPLIER
CLOCK MULTIPLIER
IDT / ICS LOCO PLL CLOCK MULTIPLIER
4
ICS503
REV D 051310
External Components
Decoupling Capacitor
As with any high-performance mixed-signal IC, the
ICS503 must be isolated from system power supply
noise to perform optimally.
A decoupling capacitor of 0.01F must be connected
between VDD and GND. It must be connected close to
the ICS503 to minimize lead inductance. No external
power supply filtering is required for the ICS503.
Series Termination Resistor
A 33
terminating resistor can be used next to the CLK
pin. The total on-chip capacitance is approximately 12
pF. A parallel resonant, fundamental mode crystal
should be used.
Crystal Load Capacitors
The device crystal connections should include pads for
small capacitors from X1 to ground and from X2 to
ground. These capacitors are used to adjust the stray
capacitance of the board to match the nominally
required crystal load capacitance. Because load
capacitance can only be increased in this trimming
process, it is important to keep stray capacitance to a
minimum by using very short PCB traces (and no vias)
between the crystal and device. Crystal capacitors, if
needed, must be connected from each of the pins X1
and X2 to ground.
The value (in pF) of these crystal caps should equal (CL
-12 pF)*2. In this equation, CL= crystal load capacitance
in pF. Example: For a crystal with a 16 pF load
capacitance, each crystal capacitor would be 8 pF
[(16-12) x 2] = 8.
Absolute Maximum Ratings
Stresses above the ratings listed below can cause permanent damage to the ICS503. These ratings, which
are standard values for IDT commercially rated parts, are stress ratings only. Functional operation of the
device at these or any other conditions above those indicated in the operational sections of the
specifications is not implied. Exposure to absolute maximum rating conditions for extended periods can
affect product reliability. Electrical parameters are guaranteed only over the recommended operating
temperature range.
Recommended Operation Conditions
Item
Rating
Supply Voltage, VDD
7 V
All Inputs and Outputs
-0.5 V to VDD+0.5 V
Ambient Operating Temperature
0 to +70
° C
Storage Temperature
-65 to +150
° C
Soldering Temperature
260
° C
Parameter
Min.
Typ.
Max.
Units
Ambient Operating Temperature
0
+70
° C
Power Supply Voltage (measured in respect to GND)
+3
+5.5
V
相关PDF资料
PDF描述
ICS501GLF IC PLL CLK MULTIPLIER 8-MSOP
SI5350A-A-GT IC CLK GEN PLL BLANK CUST 10MSOP
VI-232-IV CONVERTER MOD DC/DC 15V 150W
VE-2WX-MW-S CONVERTER MOD DC/DC 5.2V 100W
VI-J1W-MZ-F1 CONVERTER MINIMOD DC/DC 5.5V 25W
相关代理商/技术参数
参数描述
ICS503MLFT 功能描述:IC PLL CLK MULTIPLIER 8-SOIC RoHS:是 类别:集成电路 (IC) >> 时钟/计时 - 时钟发生器,PLL,频率合成器 系列:LOCO™ 标准包装:2,000 系列:- 类型:PLL 时钟发生器 PLL:带旁路 输入:LVCMOS,LVPECL 输出:LVCMOS 电路数:1 比率 - 输入:输出:2:11 差分 - 输入:输出:是/无 频率 - 最大:240MHz 除法器/乘法器:是/无 电源电压:3.135 V ~ 3.465 V 工作温度:0°C ~ 70°C 安装类型:表面贴装 封装/外壳:32-LQFP 供应商设备封装:32-TQFP(7x7) 包装:带卷 (TR)
ICS503MT 功能描述:IC PLL CLK MULTIPLIER 8-SOIC RoHS:否 类别:集成电路 (IC) >> 时钟/计时 - 时钟发生器,PLL,频率合成器 系列:LOCO™ 产品变化通告:Product Discontinuation 04/May/2011 标准包装:96 系列:- 类型:时钟倍频器,零延迟缓冲器 PLL:带旁路 输入:LVTTL 输出:LVTTL 电路数:1 比率 - 输入:输出:1:8 差分 - 输入:输出:无/无 频率 - 最大:133.3MHz 除法器/乘法器:是/无 电源电压:3 V ~ 3.6 V 工作温度:0°C ~ 70°C 安装类型:表面贴装 封装/外壳:16-TSSOP(0.173",4.40mm 宽) 供应商设备封装:16-TSSOP 包装:管件 其它名称:23S08-5HPGG
ICS504M 制造商:未知厂家 制造商全称:未知厂家 功能描述:Industrial Control IC
ICS504MT 制造商:未知厂家 制造商全称:未知厂家 功能描述:Industrial Control IC
ICS507-01 制造商:ICS 制造商全称:ICS 功能描述:PECL Clock Synthesizer