- 您现在的位置：买卖IC网 > PDF目录9203 > ICS525-01RILF (IDT, Integrated Device Technology Inc)IC CLK USER CONFIGURABLE 28-SSOP PDF资料下载
参数资料
| 型号： | ICS525-01RILF |
| 厂商： | IDT, Integrated Device Technology Inc |
| 文件页数： | 6/10页 |
| 文件大小： | 0K |
| 描述： | IC CLK USER CONFIGURABLE 28-SSOP |
| 产品培训模块： | Clock Distibution and Generation 1.0 |
| 标准包装： | 48 |
| 系列： | OSCaR™ |
| 类型： | 时钟发生器，扇出配送 |
| PLL： | 带旁路 |
| 输入： | 时钟，晶体 |
| 输出： | CMOS |
| 电路数： | 1 |
| 比率 - 输入:输出： | 1:2 |
| 差分 - 输入:输出： | 无/无 |
| 频率 - 最大： | 140MHz |
| 除法器/乘法器： | 是/无 |
| 电源电压： | 3 V ~ 5.5 V |
| 工作温度： | -40°C ~ 85°C |
| 安装类型： | 表面贴装 |
| 封装/外壳： | 28-SSOP（0.154"，3.90mm 宽） |
| 供应商设备封装： | 28-QSOP |
| 包装： | 管件 |
| 产品目录页面： | 1251 (CN2011-ZH PDF) |
| 其它名称： | 525-01RILF 800-1046 800-1046-5 800-1046-ND |
ICS525-01/02/11/12
USER CONFIGURABLE CLOCK
CLOCK MULTIPLIER
IDT USER CONFIGURABLE CLOCK
5
ICS525-01/02/11/12 REV T 053012
External Components/Crystal
Selection
Decoupling Capacitors
The ICS525-01/02/11/12 requries two 0.01F
decoupling capacitors to be connected between VDD
and GND, one on each side of the chip. The capacitor
must be connected close to the device to minimize lead
inductance.
External Resistors
A 33
Ω series termination resistor should be used on the
CLK and REF pins.
Crystal Load Capacitors
The approximate total on-chip capacitance for a crystal
is 16 pF, so a parallel resonant, fundamental mode
crystal with this value of load (correlation) capacitance
should be used. For crystals with a specified load
capacitance greater than 16 pF, crystal capacitors may
be connected from each of the pins X1 and X2 to
Ground as shown in the block diagram. The value (in
pF) of these crystal caps should be (CL -16)*2, where
CL is the crystal load capacitance in pF. These external
capacitors are only required for applications where the
exact frequency is critical. For a clock input, connect to
X1 and leave X2 unconnected (no capacitors on either).
Determining the Output Frequency
Users have full control in setting the desired output
frequency over the range shown in the tables on pages
3-4. To replace a standard oscillator, users should
connect the divider select input pins directly to ground
(or VDD, although this is not required because of
internal pull-ups) during Printed Circuit Board layout.
The ICS525 will automatically produce the correct
frequency when all components are soldered. It is also
possible to connect the inputs to parallel I/O ports to
switch frequencies. By choosing divides carefully, the
number of inputs which need to be changed can be
minimized. Observe the restrictions on allowed values
of VDW and RDW.
Configuration Pin Settings
The output of the ICS525 can be determined by the
following simple equation:
Where:
Reference Divider Word (RDW) = 0 to 127 (0 not
permitted for ICS525-01/-11)
VCO Divider Word (VDW) = 0 to 511 (0, 1, 2, 3 not
permitted for ICS525-01/-11)
Output Divider (OD) = values on pages 3-4
Also, the following operating ranges should be
observed:
1. The output frequency must be in the ranges listed on
pages 3-4.
2. The phase detector frequency must be above 200
kHz.
Since all of the inputs have pull-up resistors, it is only
necessary to ground the pins that need to be set to zero.
Which Part to Use?
The ICS525-01 is the original configurable clock.
The ICS525-02 has a higher maximum output
grequency and a slightly different set of output dividers.
The ICS525-11 has the same divider set as the -01 but
is optimized for low frequency operation.
The ICS525-12 has the same divider set as the -02 but
is optimized for low frequency operation.
To determine the best combination of VCO, reference,
and output divide, use the ICS525 Calculator on our
web site.
CLK Frequency
Input Frequency
2x
VDW
8
+
()
RDW
2
+
() OD
---------------------------------------------
×
=
200kHz
InputFrequency
RDW
2
+
()
-----------------------------------------------
<
相关PDF资料 |
PDF描述 |
|---|---|
| VI-210-MW | CONVERTER MOD DC/DC 5V 100W |
| X9409YS24Z | IC XDCP QUAD 64-TAP 2.5K 24-SOIC |
| VI-20W-MX-B1 | CONVERTER MOD DC/DC 5.5V 75W |
| X9409WS24Z | IC XDCP QUAD 64-TAP 10K 24-SOIC |
| ISL22414WMU10Z | IC DGTL POT 256POS 10K 10MSOP |
相关代理商/技术参数 |
参数描述 |
|---|---|
| ICS525-01RILFT | 功能描述:IC CLOCK USER CONFIGURE 28-SSOP RoHS:是 类别:集成电路 (IC) >> 时钟/计时 - 时钟发生器，PLL，频率合成器 系列:OSCaR™ 标准包装:2,000 系列:- 类型:PLL 时钟发生器 PLL:带旁路 输入:LVCMOS，LVPECL 输出:LVCMOS 电路数:1 比率 - 输入:输出:2:11 差分 - 输入:输出:是/无 频率 - 最大:240MHz 除法器/乘法器:是/无 电源电压:3.135 V ~ 3.465 V 工作温度:0°C ~ 70°C 安装类型:表面贴装 封装/外壳:32-LQFP 供应商设备封装:32-TQFP（7x7） 包装:带卷 (TR) |
| ICS525-01RIT | 功能描述:IC CLOCK USER CONFIGURE 28-SSOP RoHS:否 类别:集成电路 (IC) >> 时钟/计时 - 时钟发生器，PLL，频率合成器 系列:OSCaR™ 产品变化通告:Product Discontinuation 04/May/2011 标准包装:96 系列:- 类型:时钟倍频器，零延迟缓冲器 PLL:带旁路 输入:LVTTL 输出:LVTTL 电路数:1 比率 - 输入:输出:1:8 差分 - 输入:输出:无/无 频率 - 最大:133.3MHz 除法器/乘法器:是/无 电源电压:3 V ~ 3.6 V 工作温度:0°C ~ 70°C 安装类型:表面贴装 封装/外壳:16-TSSOP（0.173"，4.40mm 宽） 供应商设备封装:16-TSSOP 包装:管件 其它名称:23S08-5HPGG |
| ICS525-01RLF | 功能描述:IC CLK USER CONFIGURABLE 28-SSOP RoHS:是 类别:集成电路 (IC) >> 时钟/计时 - 时钟发生器，PLL，频率合成器 系列:OSCaR™ 标准包装:2,000 系列:- 类型:PLL 频率合成器 PLL:是 输入:晶体 输出:时钟 电路数:1 比率 - 输入:输出:1:1 差分 - 输入:输出:无/无 频率 - 最大:1GHz 除法器/乘法器:是/无 电源电压:4.5 V ~ 5.5 V 工作温度:-20°C ~ 85°C 安装类型:表面贴装 封装/外壳:16-LSSOP（0.175"，4.40mm 宽） 供应商设备封装:16-SSOP 包装:带卷 (TR) 其它名称:NJW1504V-TE1-NDNJW1504V-TE1TR |
| ICS525-01RLFT | 功能描述:IC CLK USER CONFIGURABLE 28-SSOP RoHS:是 类别:集成电路 (IC) >> 时钟/计时 - 时钟发生器，PLL，频率合成器 系列:OSCaR™ 标准包装:2,000 系列:- 类型:PLL 时钟发生器 PLL:带旁路 输入:LVCMOS，LVPECL 输出:LVCMOS 电路数:1 比率 - 输入:输出:2:11 差分 - 输入:输出:是/无 频率 - 最大:240MHz 除法器/乘法器:是/无 电源电压:3.135 V ~ 3.465 V 工作温度:0°C ~ 70°C 安装类型:表面贴装 封装/外壳:32-LQFP 供应商设备封装:32-TQFP（7x7） 包装:带卷 (TR) |
| ICS525-01RT | 功能描述:IC CLOCK USER CONFIGURE 28-SSOP RoHS:否 类别:集成电路 (IC) >> 时钟/计时 - 时钟发生器，PLL，频率合成器 系列:OSCaR™ 产品变化通告:Product Discontinuation 04/May/2011 标准包装:96 系列:- 类型:时钟倍频器，零延迟缓冲器 PLL:带旁路 输入:LVTTL 输出:LVTTL 电路数:1 比率 - 输入:输出:1:8 差分 - 输入:输出:无/无 频率 - 最大:133.3MHz 除法器/乘法器:是/无 电源电压:3 V ~ 3.6 V 工作温度:0°C ~ 70°C 安装类型:表面贴装 封装/外壳:16-TSSOP（0.173"，4.40mm 宽） 供应商设备封装:16-TSSOP 包装:管件 其它名称:23S08-5HPGG |
发布紧急采购，3分钟左右您将得到回复。