参数资料
型号: ICS650R-27ILF
厂商: INTEGRATED DEVICE TECHNOLOGY INC
元件分类: 时钟产生/分配
英文描述: 133.3333 MHz, OTHER CLOCK GENERATOR, PDSO20
封装: 0.150 INCH, ROHS COMPLIANT, SSOP-20
文件页数: 4/7页
文件大小: 230K
代理商: ICS650R-27ILF
Networking Clock Source
MDS 650-27 D
4
Revision 070505
Integrated Circuit Systems, Inc.
525 Race Street, San Jose, CA 95126 tel (408) 297-1201 www.icst.com
ICS650-27
External Components
The ICS650-27 requires a minimum number of external
components for proper operation.
Decoupling Capacitor
Decoupling capacitors of 0.01F must be connected
between each VDD and GND (pins 4 and 6, pins 16
and 14), as close to the device as possible. For
optimum device performance, the decoupling capacitor
should be mounted on the component side of the PCB.
Avoid the use of vias in the decoupling circuit.
Series Termination Resistor
When the PCB trace between the clock outputs and the
loads are over 1 inch, series termination should be
used. To series terminate a 50
trace (a commonly
used trace impedance), place a 33
resistor in series
with the clock line as close to the clock output pin as
possible. The nominal impedance of the clock output is
20
.
Crystal Information
The crystal used should be a fundamental mode (do
not use third overtone), parallel resonant. Crystal
capacitors should be connected from pins X1 to ground
and X2 to ground to optimize the initial accuracy. The
value of these capacitors is given by the following
equation:
Crystal caps (pF) = (CL - 6) x 2
In the equation, CL is the crystal load capacitance. So,
for a crystal with a 16pF load capacitance, two 20 pF
[(16-6) x 2] capacitors should be used.
Absolute Maximum Ratings
Stresses above the ratings listed below can cause permanent damage to the ICS650-27. These ratings,
which are standard values for ICS commercially rated parts, are stress ratings only. Functional operation of
the device at these or any other conditions above those indicated in the operational sections of the
specifications is not implied. Exposure to absolute maximum rating conditions for extended periods can
affect product reliability. Electrical parameters are guaranteed only over the recommended operating
temperature range.
Recommended Operation Conditions
Item
Rating
Supply Voltage, VDD
7 V
All Inputs and Outputs
-0.5 V to VDD+0.5 V
Ambient Operating Temperature
-40 to +85
°C
Storage Temperature
-65 to +150
°C
Junction Temperature
175
°C
Soldering Temperature
260
°C
Parameter
Min.
Typ.
Max.
Units
Ambient Operating Temperature
-40
+85
°C
Power Supply Voltage (measured in respect to GND)
+3.0
+3.3
+3.6
V
ICS650-27
Networking Clock Source
TSD
IDT / ICS Networking Clock Source
ICS650-27
4
相关PDF资料
PDF描述
ICS650R-27IT 133.3333 MHz, OTHER CLOCK GENERATOR, PDSO20
ICS651MIT 651 SERIES, LOW SKEW CLOCK DRIVER, 4 TRUE OUTPUT(S), 0 INVERTED OUTPUT(S), PDSO8
ICS651MT 651 SERIES, LOW SKEW CLOCK DRIVER, 4 TRUE OUTPUT(S), 0 INVERTED OUTPUT(S), PDSO8
ICS651MLFT 651 SERIES, LOW SKEW CLOCK DRIVER, 4 TRUE OUTPUT(S), 0 INVERTED OUTPUT(S), PDSO8
ICS651MLF 651 SERIES, LOW SKEW CLOCK DRIVER, 4 TRUE OUTPUT(S), 0 INVERTED OUTPUT(S), PDSO8
相关代理商/技术参数
参数描述
ICS650R-27ILFT 功能描述:IC CLOCK SYNTHESIZER 20-SSOP RoHS:是 类别:集成电路 (IC) >> 时钟/计时 - 时钟发生器,PLL,频率合成器 系列:- 标准包装:2,000 系列:- 类型:PLL 时钟发生器 PLL:带旁路 输入:LVCMOS,LVPECL 输出:LVCMOS 电路数:1 比率 - 输入:输出:2:11 差分 - 输入:输出:是/无 频率 - 最大:240MHz 除法器/乘法器:是/无 电源电压:3.135 V ~ 3.465 V 工作温度:0°C ~ 70°C 安装类型:表面贴装 封装/外壳:32-LQFP 供应商设备封装:32-TQFP(7x7) 包装:带卷 (TR)
ICS650R-27IT 功能描述:IC CLK SOURCE NETWORK 20-SSOP RoHS:否 类别:集成电路 (IC) >> 时钟/计时 - 时钟发生器,PLL,频率合成器 系列:- 产品变化通告:Product Discontinuation 04/May/2011 标准包装:96 系列:- 类型:时钟倍频器,零延迟缓冲器 PLL:带旁路 输入:LVTTL 输出:LVTTL 电路数:1 比率 - 输入:输出:1:8 差分 - 输入:输出:无/无 频率 - 最大:133.3MHz 除法器/乘法器:是/无 电源电压:3 V ~ 3.6 V 工作温度:0°C ~ 70°C 安装类型:表面贴装 封装/外壳:16-TSSOP(0.173",4.40mm 宽) 供应商设备封装:16-TSSOP 包装:管件 其它名称:23S08-5HPGG
ICS651 制造商:ICS 制造商全称:ICS 功能描述:LOW SKEW 1 TO 4 CLOCK BUFFER
ICS65-1 制造商:Thomas & Betts 功能描述:INSULATED SERV.ENTR.SLEEVE 制造商:Thomas & Betts 功能描述:Cable Accessories Compression Splice Aluminum
ICS651-03 制造商:ICS 制造商全称:ICS 功能描述:VOIP Clock Source