- 您现在的位置：买卖IC网 > PDF目录2071 > ICS660GILFT (IDT, Integrated Device Technology Inc)IC CLK SOURCE DGTL VID 16-TSSOP PDF资料下载
参数资料
| 型号： | ICS660GILFT |
| 厂商： | IDT, Integrated Device Technology Inc |
| 文件页数： | 3/7页 |
| 文件大小： | 0K |
| 描述： | IC CLK SOURCE DGTL VID 16-TSSOP |
| 标准包装： | 2,500 |
| 类型： | 时钟发生器 |
| 应用： | 数字视频 |
| 安装类型： | 表面贴装 |
| 封装/外壳： | 16-TSSOP（0.173"，4.40mm 宽） |
| 供应商设备封装： | 16-TSSOP |
| 包装： | 带卷 (TR) |
| 其它名称： | 660GILFT |
ICS660
DIGITAL VIDEO CLOCK SOURCE
CLOCK SYNTHESIZER
IDT / ICS DIGITAL VIDEO CLOCK SOURCE
3
ICS660
REV G 051310
Application Information
Series Termination Resistor
Clock output traces should use series termination. To series
terminate a 50
trace (a commonly used trace impedance),
place a 33
resistor in series with the clock line, as close to
the clock output pin as possible. The nominal impedance of
the clock output is 20
.
Decoupling Capacitors
As with any high-performance mixed-signal IC, the ICS660
must be isolated from system power supply noise to perform
optimally.
Decoupling capacitors of 0.01F must be connected
between each VDD and the PCB ground plane. To further
guard against interfering system supply noise, the ICS660
should use one common connection to the PCB power
plane as shown in the diagram on the next page. The ferrite
bead and bulk capacitor help reduce lower frequency noise
in the supply that can lead to output clock phase modulation.
Recommended Power Supply Connection for
Optimal Device Performance
All power supply pins must be connected to the same
voltage, except VDDR and VDDO, which may be connected
to a lower voltage in order to change the output level. If the
reference output is not used, ground VDDR.
Crystal Load Capacitors
If a crystal is used, the device crystal connections should
include pads for capacitors from X1 to ground and from X2
to ground. These capacitors are used to adjust the stray
capacitance of the board to match the nominally required
crystal load capacitance. To reduce possible noise pickup,
use very short PCB traces (and no vias) been the crystal
and device.
The value of the load capacitors can be roughly determined
by the formula C = 2(CL - 6) where C is the load capacitor
connected to X1 and X2, and CL is the specified value of the
load capacitance for the crystal. A typical crystal CL is 18 pF,
so C = 2(18 - 6) = 24 pF. Because these capacitors adjust
the stray capacitance of the PCB, check the output
frequency using your final layout to see if the value of C
should be changed.
PCB Layout Recommendations
For optimum device performance and lowest output phase
noise, the following guidelines should be observed.
1) Each 0.01F decoupling capacitor should be mounted on
the component side of the board as close to the VDD pin as
possible. No vias should be used between decoupling
capacitor and VDD pin. The PCB trace to VDD pin should
be kept as short as possible, as should the PCB trace to the
ground via. Distance of the ferrite bead and bulk decoupling
from the device is less critical.
2) The external crystal should be mounted next to the device
with short traces. The X1 and X2 traces should not be
routed next to each other with minimum spaces, instead
they should be separated and away from other traces.
3) To minimize EMI, and obtain the best signal integrity, the
33
series termination resistor should be placed close to
the clock output.
4) An optimum layout is one with all components on the
same side of the board, minimizing vias through other signal
layers (the ferrite bead and bulk decoupling capacitor can be
mounted on the back). Other signal traces should be routed
away from the ICS660. This includes signal traces just
underneath the device, or on layers adjacent to the ground
plane layer used by the device.
C onnec tion to 3.3V
Pow er Plane
Ferrite
B ead
B ulk D ec oupling C apac itor
(suc h as 1
F Tantalum )
VD D Pin
0.01
F D ecoupling C apacitors
相关PDF资料 |
PDF描述 |
|---|---|
| ICS661GILF | IC AUDIO CLK SOURCE PREC 16TSSOP |
| ICS662M-03LFT | IC CLK SOURCE HDTV AUD/VID 8SOIC |
| ICS664G-02LFT | IC CLK SOURCE DGTL VIDEO 16TSSOP |
| ICS664G-03LFT | IC CLK SOURCE DGTL VIDEO 16TSSOP |
| ICS664G-05LFT | IC CLK SOURCE DGTL VIDEO 16TSSOP |
相关代理商/技术参数 |
参数描述 |
|---|---|
| ICS660GIT | 功能描述:IC CLK SOURCE DGTL VID 16-TSSOP RoHS:否 类别:集成电路 (IC) >> 线性 - 视频处理 系列:- 产品变化通告:Product Discontinuation 07/Mar/2011 标准包装:3,000 系列:OMNITUNE™ 类型:调谐器 应用:移动电话，手机，视频显示器 安装类型:表面贴装 封装/外壳:65-WFBGA 供应商设备封装:PG-WFSGA-65 包装:带卷 (TR) 其它名称:SP000365064 |
| ICS660GITR | 制造商:ICS 制造商全称:ICS 功能描述:Digital Video Clock Source |
| ICS661 | 制造商:ICS 制造商全称:ICS 功能描述:Precision Audio Clock Source |
| ICS66-1 | 制造商:Thomas & Betts 功能描述:INSULATED SERV.ENTR.SLEEVE 制造商:Thomas & Betts 功能描述:Cable Accessories Compression Splice Aluminum |
| ICS661GI | 功能描述:IC CLK SOURCE PREC AUD 16-TSSOP RoHS:否 类别:集成电路 (IC) >> 时钟/计时 - 时钟发生器，PLL，频率合成器 系列:- 产品变化通告:Product Discontinuation 04/May/2011 标准包装:96 系列:- 类型:时钟倍频器，零延迟缓冲器 PLL:带旁路 输入:LVTTL 输出:LVTTL 电路数:1 比率 - 输入:输出:1:8 差分 - 输入:输出:无/无 频率 - 最大:133.3MHz 除法器/乘法器:是/无 电源电压:3 V ~ 3.6 V 工作温度:0°C ~ 70°C 安装类型:表面贴装 封装/外壳:16-TSSOP（0.173"，4.40mm 宽） 供应商设备封装:16-TSSOP 包装:管件 其它名称:23S08-5HPGG |
发布紧急采购，3分钟左右您将得到回复。