- 您现在的位置：买卖IC网 > PDF目录67704 > ICS9147F-01LF (INTEGRATED DEVICE TECHNOLOGY INC) 83.3 MHz, PROC SPECIFIC CLOCK GENERATOR, PDSO48 PDF资料下载
参数资料
| 型号： | ICS9147F-01LF |
| 厂商： | INTEGRATED DEVICE TECHNOLOGY INC |
| 元件分类： | 时钟产生/分配 |
| 英文描述： | 83.3 MHz, PROC SPECIFIC CLOCK GENERATOR, PDSO48 |
| 封装： | 0.300 INCH, SSOP-48 |
| 文件页数： | 10/11页 |
| 文件大小： | 442K |
| 代理商： | ICS9147F-01LF |
8
ICS9147-01
Pins 1 and 2 on the ICS9147-01 serve as dual signal functions
to the device. During initial power-up, they act as input
pins. The logic level (voltage) that is present on these pins at
this time is read and stored into a 4-bit internal data latch. At
the end of Power-On reset, (see AC characteristics for timing
values), the device changes the mode of operations for these
pins to an output function. In this mode the pins produce the
specified buffered clocks to external loads.
To program (load) the internal configuration register for
these pins, a resistor is connected to either the VDD (logic 1)
power supply or the GND (logic 0) voltage potential. A 10
Kilohm(10K) resistor is used to provide both the solid CMOS
programming voltage needed during the power-up
programming period and to provide an insignificant load on
the output clock during the subsequent operating period.
Figs. 1 and 2 show the recommended means of implementing
this function. In Fig. 1 either one of the resistors is loaded
onto the board (selective stuffing) to configure the device’s
internal logic. Figs. 2a and b
provide a single resistor
loading option where either solder spot tabs or a physical
jumper header may be used.
These figures illustrate the optimal PCB physical layout
options. These configuration resistors are of such a large
ohmic value that they do not effect the low impedance clock
signals. The layouts have been optimized to provide as little
impedance transition to the clock signal as possible, as it
passes through the programming resistor pad(s).
Shared Pin Operation -
Input/Output Pins
The ICS9147-01 includes a production test verification
mode of operation. This requires that the FSO and FS1 pins
be programmed to a logic high and the FS2 pin be
programmed to a
logic low(see
Shared Pin Operation
section). In this mode the device will output the following
frequencies.
Note: REF is the frequency of either the crystal connected
between the devices X1and X2 or, in the case of a device
being driven by an external reference clock, the frequency
of the reference (or test) clock on the device’s X1 pin.
Test Mode Operation
Fig. 1
n
i
P
y
c
n
e
u
q
e
r
F
C
I
P
A
O
I
,
F
E
RF
E
R
z
H
M
8
42
/
F
E
R
z
H
M
4
24
/
F
E
R
,
U
P
C
M
A
R
D
S
2
/
F
E
R
)
6
:
1
(
S
U
B4
/
F
E
R
相关PDF资料 |
PDF描述 |
|---|---|
| ICS9147F-01T-LF | 83.3 MHz, PROC SPECIFIC CLOCK GENERATOR, PDSO48 |
| ICS9147F-01T | 83.3 MHz, PROC SPECIFIC CLOCK GENERATOR, PDSO48 |
| ICS9148F-03 | 83.3 MHz, PROC SPECIFIC CLOCK GENERATOR, PDSO48 |
| ICS9148F-08 | 83.3 MHz, PROC SPECIFIC CLOCK GENERATOR, PDSO48 |
| ICS9148F-11 | 66.6 MHz, PROC SPECIFIC CLOCK GENERATOR, PDSO48 |
相关代理商/技术参数 |
参数描述 |
|---|---|
| ICS9147F-03 | 制造商:INT_CIR_SYS 功能描述: |
| ICS9147F-06 | 制造商:ICS 制造商全称:ICS 功能描述:Frequency Generator & Integrated Buffers for PENTIUMTM |
| ICS9147F-06T | 制造商:ICS 功能描述: |
| ICS9147F-08 | 制造商:未知厂家 制造商全称:未知厂家 功能描述:CPU System Clock Generator |
| ICS9147F-08T | 制造商:ICS 功能描述: |
发布紧急采购，3分钟左右您将得到回复。