- 您现在的位置：买卖IC网 > PDF目录67708 > ICS951411YGLFT 400 MHz, PROC SPECIFIC CLOCK GENERATOR, PDSO56 PDF资料下载
参数资料
| 型号： | ICS951411YGLFT |
| 元件分类： | 时钟产生/分配 |
| 英文描述： | 400 MHz, PROC SPECIFIC CLOCK GENERATOR, PDSO56 |
| 封装： | 6.10 MM, 0.50 MM PITCH, LEAD FREE, MO-153, TSSOP-56 |
| 文件页数： | 9/19页 |
| 文件大小： | 194K |
| 代理商： | ICS951411YGLFT |
17
Integrated
Circuit
Systems, Inc.
ICS951411
0891E—03/07/05
Fig. 1
Shared Pin Operation -
Input/Output Pins
The I/O pins designated by (input/output) on the ICS951416
serve as dual signal functions to the device. During initial
power-up, they act as input pins. The logic level (voltage)
that is present on these pins at this time is read and stored
into a 5-bit internal data latch. At the end of Power-On reset,
(see AC characteristics for timing values), the device
changes the mode of operations for these pins to an output
function. In this mode the pins produce the specified buffered
clocks to external loads.
To program (load) the internal configuration register for
these pins, a resistor is connected to either the VDD (logic 1)
power supply or the GND (logic 0) voltage potential. A 10
Kilohm (10K) resistor is used to provide both the solid CMOS
programming voltage needed during the power-up
programming period and to provide an insignificant load on
the output clock during the subsequent operating period.
Via to
VDD
Clock trace to load
Series Term. Res.
Programming
Header
Via to Gnd
Device
Pad
2K
W
8.2K
W
Figure 1 shows a means of implementing this function
when a switch or 2 pin header is used. With no jumper is
installed the pin will be pulled high. With the jumper in
place the pin will be pulled low. If programmability is not
necessary, than only a single resistor is necessary. The
programming resistors should be located close to the series
termination resistor to minimize the current loop area. It is
more important to locate the series termination resistor
close to the driver than the programming resistor.
相关PDF资料 |
PDF描述 |
|---|---|
| ICS951412YGLFT | 220 MHz, PROC SPECIFIC CLOCK GENERATOR, PDSO56 |
| ICS951412YGT | 220 MHz, PROC SPECIFIC CLOCK GENERATOR, PDSO56 |
| ICS951413YFLFT | 400 MHz, PROC SPECIFIC CLOCK GENERATOR, PDSO56 |
| ICS951413YGT | 400 MHz, PROC SPECIFIC CLOCK GENERATOR, PDSO56 |
| ICS951413YGLFT | 400 MHz, PROC SPECIFIC CLOCK GENERATOR, PDSO56 |
相关代理商/技术参数 |
参数描述 |
|---|---|
| ICS951412 | 制造商:ICS 制造商全称:ICS 功能描述:System Clock Chip for ATI RS480 K8-based Systems |
| ICS951412AFLF | 功能描述:IC SYSTEM CLOCK CHIP K8 56-SSOP RoHS:是 类别:集成电路 (IC) >> 时钟/计时 - 专用 系列:PCI Express® (PCIe) 标准包装:1,500 系列:- 类型:时钟缓冲器/驱动器 PLL:是 主要目的:- 输入:- 输出:- 电路数:- 比率 - 输入:输出:- 差分 - 输入:输出:- 频率 - 最大:- 电源电压:3.3V 工作温度:0°C ~ 70°C 安装类型:表面贴装 封装/外壳:28-SSOP（0.209"，5.30mm 宽） 供应商设备封装:28-SSOP 包装:带卷 (TR) 其它名称:93786AFT |
| ICS951412AFLFT | 功能描述:IC SYSTEM CLOCK CHIP K8 56-SSOP RoHS:是 类别:集成电路 (IC) >> 时钟/计时 - 专用 系列:PCI Express® (PCIe) 标准包装:1,500 系列:- 类型:时钟缓冲器/驱动器 PLL:是 主要目的:- 输入:- 输出:- 电路数:- 比率 - 输入:输出:- 差分 - 输入:输出:- 频率 - 最大:- 电源电压:3.3V 工作温度:0°C ~ 70°C 安装类型:表面贴装 封装/外壳:28-SSOP（0.209"，5.30mm 宽） 供应商设备封装:28-SSOP 包装:带卷 (TR) 其它名称:93786AFT |
| ICS951412AGLF | 功能描述:IC SYSTEM CLOCK CHIP K8 56-TSSOP RoHS:是 类别:集成电路 (IC) >> 时钟/计时 - 专用 系列:PCI Express® (PCIe) 标准包装:1,500 系列:- 类型:时钟缓冲器/驱动器 PLL:是 主要目的:- 输入:- 输出:- 电路数:- 比率 - 输入:输出:- 差分 - 输入:输出:- 频率 - 最大:- 电源电压:3.3V 工作温度:0°C ~ 70°C 安装类型:表面贴装 封装/外壳:28-SSOP（0.209"，5.30mm 宽） 供应商设备封装:28-SSOP 包装:带卷 (TR) 其它名称:93786AFT |
| ICS951412AGLFT | 功能描述:IC SYSTEM CLOCK CHIP K8 56-TSSOP RoHS:是 类别:集成电路 (IC) >> 时钟/计时 - 专用 系列:PCI Express® (PCIe) 标准包装:1,500 系列:- 类型:时钟缓冲器/驱动器 PLL:是 主要目的:- 输入:- 输出:- 电路数:- 比率 - 输入:输出:- 差分 - 输入:输出:- 频率 - 最大:- 电源电压:3.3V 工作温度:0°C ~ 70°C 安装类型:表面贴装 封装/外壳:28-SSOP（0.209"，5.30mm 宽） 供应商设备封装:28-SSOP 包装:带卷 (TR) 其它名称:93786AFT |
发布紧急采购，3分钟左右您将得到回复。