- 您现在的位置：买卖IC网 > PDF目录383096 > ICX209AL (Sony Corporation) Diagonal 4.5mm (Type 1/4) CCD Image Sensor for CCIR B/W Video Cameras PDF资料下载
参数资料
| 型号： | ICX209AL |
| 厂商： | Sony Corporation |
| 英文描述： | Diagonal 4.5mm (Type 1/4) CCD Image Sensor for CCIR B/W Video Cameras |
| 中文描述： | 对角线4.5毫米（类型1 / 4）CCD图像传感器的无线电咨询委员会/黑白视频摄像机 |
| 文件页数： | 10/18页 |
| 文件大小： | 230K |
| 代理商： | ICX209AL |
– 10 –
ICX209AK
Definition of standard imaging conditions
1) Standard imaging condition
I
:
Use a pattern box (luminance 706cd/m
2
, color temperature of 3200K halogen source) as a subject. (Pattern
for evaluation is not applicable.) Use a testing standard lens with CM500S (t = 1.0mm) as an IR cut filter and
image at F5.6. The luminous intensity to the sensor receiving surface at this point is defined as the standard
sensitivity testing luminous intensity.
2) Standard imaging condition
II
:
Image a light source (color temperature of 3200K) with a uniformity of brightness within 2% at all angles.
Use a testing standard lens with CM500S (t = 1.0mm) as an IR cut filter. The luminous intensity is adjusted
to the value indicated in each testing item by the lens diaphragm.
3) Standard imaging condition
III
:
Image a light source (color temperature of 3200K) with a uniformity of brightness within 2% at all angles.
Use a testing standard lens (exit pupil distance –33mm) with CM500S (t = 1.0mm) as an IR cut filter. The
luminous intensity is adjusted to the value indicated in each testing item by the lens diaphragm.
1. Sensitivity
Set to standard imaging condition
I
. After selecting the electronic shutter mode with a shutter speed of
1/250s, measure the Y signal (Ys) at the center of the screen and substitute the value into the following
formula.
250
S = Ys
×
[mV]
2. Sensitivity ratio
Set to standard imaging condition
II
. Adjust the luminous intensity so that the average value of the Y signal
output is 200mV, and then measure the Mg signal output (S
Mg
[mV]) and G signal output (S
G
[mV]), and Ye
signal output (S
Ye
[mV]) and Cy signal output (S
Cy
[mV]) at the center of the screen with frame readout
method. Substitute the values into the following formula.
R
MgG
= S
Mg
/S
G
R
YeCy
= S
Ye
/S
Cy
3. Saturation signal
Set to standard imaging condition
II
. After adjusting the luminous intensity to 10 times the intensity with
average value of the Y signal output, 200mV, measure the minimum value of the Y signal.
4. Smear
Set to standard imaging condition
II
. With the lens diaphragm at F5.6 to F8, adjust the luminous intensity to
500 times the intensity with average value of the Y signal output, 200mV. When the readout clock is
stopped and the charge drain is executed by the electronic shutter at the respective H blankings, measure
the maximum value YSm [mV] of the Y signal output and substitute the value into the following formula.
YSm
500
10
5. Video signal shading
Set to standard imaging condition
III
. With the lens diaphragm at F5.6 to F8, adjust the luminous intensity
so that the average value of the Y signal output is 200mV. Then measure the maximum (Ymax [mV]) and
minimum (Ymin [mV]) values of the Y signal and substitute the values into the following formula.
SHy = (Ymax – Ymin)/200
×
100 [%]
6. Uniformity between video signal channels
Set to standard imaging condition
II
. Adjust the luminous intensity so that the average value of the Y signal
output is 200mV, and then measure the maximum (Crmax, Cbmax [mV]) and minimum (Crmin, Cbmin
[mV]) values of the R – Y and B – Y channels of the chroma signal and substitute the values into the
following formula.
Sr = | (Crmax – Crmin)/200 |
×
100 [%]
Sb = | (Cbmax – Cbmin)/200 |
×
100 [%]
Sm =
×
100 [%] (1/10V method conversion value)
×
×
200
1
1
50
相关PDF资料 |
PDF描述 |
|---|---|
| ICX209 | RES SM 3K6 0.125W 5% 200V 200PPM/C 1206 |
| ICX224AKF | Diagonal 8mm (Type 1/2) Frame Readout CCD Image Sensor with Square Pixel for Color Cameras |
| ICX224 | Timing Generator for Frame Readout CCD Image Sensor |
| ICX224AK | Diagonal 8mm (Type 1/2) Frame Readout CCD Image Sensor with Square Pixel for Color Cameras |
| ICX224AQ | Diagonal 8mm (Type 1/2) Frame Readout CCD Image Sensor with Square Pixel for Color Cameras |
相关代理商/技术参数 |
参数描述 |
|---|---|
| ICX224 | 制造商:SONY 制造商全称:Sony Corporation 功能描述:Timing Generator and Signal Processor for Frame Readout CCD Image Sensor |
| ICX224AK | 制造商:SONY 制造商全称:Sony Corporation 功能描述:Diagonal 8mm (Type 1/2) Frame Readout CCD Image Sensor with Square Pixel for Color Cameras |
| ICX224AKF | 制造商:SONY 制造商全称:Sony Corporation 功能描述:Diagonal 8mm (Type 1/2) Frame Readout CCD Image Sensor with Square Pixel for Color Cameras |
| ICX224AQ | 制造商:SONY 制造商全称:Sony Corporation 功能描述:Diagonal 8mm (Type 1/2) Frame Readout CCD Image Sensor with Square Pixel for Color Cameras |
| ICX224AQF | 制造商:SONY 制造商全称:Sony Corporation 功能描述:Diagonal 8mm (Type 1/2) Frame Readout CCD Image Sensor with Square Pixel for Color Cameras |
发布紧急采购，3分钟左右您将得到回复。