参数资料
型号: ICX254AL
厂商: Sony Corporation
英文描述: Diagonal 6mm (Type 1/3) CCD Image Sensor For EIA B/W Video Cameras(对角线式、6毫米(1/3型)CCD图像传感器(用于EIA黑白摄像机))
中文描述: 对角线6毫米(类型1 / 3)CCD图像传感器的环境影响评估/黑白摄像机(对角线式,6毫米(1 / 3型)防治荒漠化公约图像传感器(用于评估黑白摄像机))
文件页数: 9/17页
文件大小: 181K
代理商: ICX254AL
ICX254AL
Image Sensor Characteristics Measurement Method
Measurement conditions
1) In the following measurements, the device drive conditions are at the typical values of the bias and clock
voltage conditions.
2) In the following measurements, spot blemishes are excluded and, unless otherwise specified, the optical
black (OB) level is used as the reference for the signal output, and the value measured at point [
A] in the
drive circuit example is used.
Definition of standard imaging conditions
1) Standard imaging condition
I
:
Use a pattern box (luminance: 706cd/m
2
, color temperature of 3200K halogen source) as a subject.
(Pattern for evaluation is not applicable.) Use a testing standard lens with CM500S (t = 1.0mm) as an IR cut
filter and image at F8. The luminous intensity to the sensor receiving surface at this point is defined as the
standard sensitivity testing luminous intensity.
2) Standard imaging condition
II
:
Indicate the state which removes an IR cut filter of standard imaging condition
I
.
3) Standard imaging condition
III
:
Image a light source (color temperature of 3200K) with a uniformity of brightness within 2% at all angles.
Use a testing standard lens with CM500S (t = 1.0mm) as an IR cut filter. The luminous intensity is adjusted
to the value indicated in each testing item by the lens diaphragm.
1. Sensitivity 1
Set to standard imaging condition
I
. After selecting the electronic shutter mode with a shutter speed of
1/250s, measure the signal output (Vs
1)
at the center of the screen and
substitute the value into the following formula.
60
2. Sensitivity 2
Set to standard imaging condition
II
. After selecting the electronic shutter mode with a shutter speed of
1/1000s, measure the signal output (Vs
2
) at the center of the screen
and substitute the value into the following formula.
60
3. Saturation signal
Set to standard imaging condition
III
. After adjusting the luminous intensity to 10 times the intensity with the
average value of the signal output, 200mV, measure the minimum value of the signal output.
4. Smear
Set to standard imaging condition
III
. With the lens diaphragm at F5.6 to F8, adjust the luminous intensity to
500 times the intensity with average value of the signal output, 200mV. When the readout clock is stopped
and the charge drain is executed by the electronic shutter at the respective H blankings, measure the
maximum value YSm [mV] of the signal output and substitute the value into the following formula.
S1 = Vs
1
×
[mV]
250
S2 = Vs
2
×
[mV]
1000
Sm = 20
×
log
[dB] (1/10V method conversion value)
×
×
500
1
200
VSm
10
1
– 9 –
相关PDF资料
PDF描述
ICX255AK Diagonal 6mm (Type 1/3) CCD Image Sensor for PAL Color Video Cameras
ICX255AL Diagonal 6mm (Type 1/3) CCD Image Sensor for CCIR B/W Video Cameras
ICX258AK Diagonal 6mm (Type 1/3) CCD Image Sensor for NTSC Color Video Cameras(对角线式、6毫米(1/3型)CCD图像传感器(用于NTSC彩色摄像机))
ICX258AL Diagonal 6mm (Type 1/3) CCD Image Sensor for EIA B/W Video Cameras(对角线式、6毫米(1/3型)CCD图像传感器(用于EIA黑白摄像机))
ICX259AK Diagonal 6mm (Type 1/3) CCD Image Sensor for PAL Color Video Cameras
相关代理商/技术参数
参数描述
ICX255AK 制造商:SONY 制造商全称:Sony Corporation 功能描述:Diagonal 6mm (Type 1/3) CCD Image Sensor for PAL Color Video Cameras
ICX255AL 制造商:SONY 制造商全称:Sony Corporation 功能描述:Diagonal 6mm (Type 1/3) CCD Image Sensor for CCIR B/W Video Cameras
ICX258AK 制造商:SONY 制造商全称:Sony Corporation 功能描述:Diagonal 6mm (Type 1/3) CCD Image Sensor for NTSC Color Video Cameras
ICX258AL 制造商:SONY 制造商全称:Sony Corporation 功能描述:Diagonal 6mm (Type 1/3) CCD Image Sensor for EIA B/W Video Cameras
ICX259AK 制造商:Sony Batteries 功能描述: