- 您现在的位置：买卖IC网 > PDF目录67712 > IDT5T9820NLGI (INTEGRATED DEVICE TECHNOLOGY INC) 5T SERIES, PLL BASED CLOCK DRIVER, 10 TRUE OUTPUT(S), 0 INVERTED OUTPUT(S), QCC68 PDF资料下载
参数资料
| 型号： | IDT5T9820NLGI |
| 厂商： | INTEGRATED DEVICE TECHNOLOGY INC |
| 元件分类： | 时钟及定时 |
| 英文描述： | 5T SERIES, PLL BASED CLOCK DRIVER, 10 TRUE OUTPUT(S), 0 INVERTED OUTPUT(S), QCC68 |
| 封装： | GREEN, PLASTIC, VFQFPN-68 |
| 文件页数： | 8/36页 |
| 文件大小： | 275K |
| 代理商： | IDT5T9820NLGI |
第1页第2页第3页第4页第5页第6页第7页当前第8页第9页第10页第11页第12页第13页第14页第15页第16页第17页第18页第19页第20页第21页第22页第23页第24页第25页第26页第27页第28页第29页第30页第31页第32页第33页第34页第35页第36页
16
INDUSTRIALTEMPERATURERANGE
IDT5T9820
EEPROM PROGRAMMABLE 2.5V ZERO DELAY PLL CLOCK DRIVER
NOTES:
1. See RECOMMENDED OPERATING RANGE table.
2. For 1.8V LVTTL single-ended operation, Bits 35 - 30 = 0 and REF[1:0]/VREF[1:0] is left floating. If Bits 47/46, 45/44, 43/42, 41/40, 39/38, 37/36 = 0/1, FB/VREF2 should be left floating.
3. VDIF specifies the minimum input differential voltage (VTR - VCP) required for switching where VTR is the "true" input level and VCP is the "complement" input level. Differential mode
only. The DC differential voltage must be maintained to guarantee retaining the existing HIGH or LOW input. The AC differential voltage must be achieved to guarantee switching
to a new state.
4. VCM specifies the maximum allowable range of (VTR + VCP) /2. Differential mode only.
5. For single-ended operation in differential mode, REF[1:0]/VREF[1:0] is tied to the DC voltage VREF[1:0]. The input is guaranteed to toggle within ±200mV of VREF[1:0] when VREF[1:0]
is constrained within +600mV and VDDI-600mV, where VDDI is the nominal 1.8V power supply of the device driving the REF[1:0] input. To guarantee switching in voltage range
specified in the JEDEC 1.8V LVTTL interface specification, VREF[1:0] must be maintained at 900mV with appropriate tolerances.
6. Voltage required to maintain a logic HIGH, single-ended operation in differential mode.
7. Voltage required to maintain a logic LOW, single-ended operation in differential mode.
8. Typical values are at VDD = 2.5V, VDDQN = 1.8V, +25°C ambient.
9. The reference clock input is capable of HSTL, eHSTL, LVEPECL, 1.8V or 2.5V LVTTL operation independent of the device output. (See Input/Output Selection table.)
10. This value is the worst case minimum VIH over the specification range of the 1.8V power supply. The 1.8V LVTTL specification is VIH = 0.65 * VDD where VDD is 1.8V ± 0.15V.
However, the LVTTL translator is supplied by a 2.5V nominal supply on this part. To ensure compliance with the specification, the translator was designed to accept the calculated
worst case value ( VIH = 0.65 * [1.8 - 0.15V]) rather than reference against a nominal 1.8V supply.
11. This value is the worst case maximum VIL over the specification range of the 1.8V power supply. The 1.8V LVTTL specification is VIL = 0.35 * VDD where VDD is 1.8V ± 0.15V.
However, the LVTTL translator is supplied by a 2.5V nominal supply on this part. To ensure compliance with the specification, the translator was designed to accept the calculated
worst case value ( VIL = 0.35 * [1.8 + 0.15V]) rather than reference against a nominal 1.8V supply.
DC ELECTRICAL CHARACTERISTICS OVER OPERATING RANGE FOR 1.8V
LVTTL(1)
Symbol
Parameter
Test Conditions
Min.
Typ.(8)
Max
Unit
InputCharacteristics
IIH
Input HIGH Current
VDD = 2.7V
VI = VDDQN/GND
—
±5
A
IIL
InputLOWCurrent
VDD = 2.7V
VI = GND/VDDQN
——
±5
VIK
ClampDiodeVoltage
VDD = 2.3V, IIN = -18mA
—
- 0.7
- 1.2
V
VIN
DCInputVoltage
- 0.3
VDDQN + 0.3
V
Single-Ended Inputs(2)
VIH
DC Input HIGH
1.073(10)
—V
VIL
DC Input LOW
—
0.683(11)
V
DifferentialInputs
VDIF
DCDifferentialVoltage(3,9)
0.2
—
V
VCM
DC Common Mode Input Voltage(4,9)
825
900
975
mV
VIH
DC Input HIGH(5,6,9)
VREF + 100
—
mV
VIL
DC Input LOW(5,7,9)
—VREF - 100
mV
VREF
Single-EndedReferenceVoltage(5,9)
—
900
—
mV
OutputCharacteristics
VOH
Output HIGH Voltage
IOH = -6mA
VDDQN - 0.4
—
V
IOH = -100
AVDDQN - 0.1
—
V
VOL
OutputLOWVoltage
IOL = 6mA
—
0.4
V
IOL = 100
A
—
0.1
V
相关PDF资料 |
PDF描述 |
|---|---|
| IDT5T9890NLI | 5T SERIES, PLL BASED CLOCK DRIVER, 10 TRUE OUTPUT(S), 0 INVERTED OUTPUT(S), PQCC68 |
| IDT5T9890NLI8 | 5T SERIES, PLL BASED CLOCK DRIVER, 10 TRUE OUTPUT(S), 0 INVERTED OUTPUT(S), PQCC68 |
| IDT5T9955BFGI8 | 5T SERIES, PLL BASED CLOCK DRIVER, 8 TRUE OUTPUT(S), 0 INVERTED OUTPUT(S), PBGA96 |
| IDT5V9888PFGI8 | 500 MHz, OTHER CLOCK GENERATOR, PQFP32 |
| IDT5V9888PFGI | 500 MHz, OTHER CLOCK GENERATOR, PQFP32 |
相关代理商/技术参数 |
参数描述 |
|---|---|
| IDT5T9820NLGI8 | 功能描述:IC CLK DRIVER ZD PLL 68-VFQFPN RoHS:是 类别:集成电路 (IC) >> 时钟/计时 - 时钟发生器，PLL，频率合成器 系列:- 标准包装:39 系列:- 类型:* PLL:带旁路 输入:时钟 输出:时钟 电路数:1 比率 - 输入:输出:1:10 差分 - 输入:输出:是/是 频率 - 最大:170MHz 除法器/乘法器:无/无 电源电压:2.375 V ~ 3.465 V 工作温度:0°C ~ 70°C 安装类型:* 封装/外壳:* 供应商设备封装:* 包装:* |
| IDT5T9820NLI | 功能描述:IC CLK DRIVER ZD PLL 68-VFQFPN RoHS:否 类别:集成电路 (IC) >> 时钟/计时 - 时钟发生器，PLL，频率合成器 系列:- 标准包装:39 系列:- 类型:* PLL:带旁路 输入:时钟 输出:时钟 电路数:1 比率 - 输入:输出:1:10 差分 - 输入:输出:是/是 频率 - 最大:170MHz 除法器/乘法器:无/无 电源电压:2.375 V ~ 3.465 V 工作温度:0°C ~ 70°C 安装类型:* 封装/外壳:* 供应商设备封装:* 包装:* |
| IDT5T9820NLI8 | 功能描述:IC CLK DRIVER ZD PLL 68-VFQFPN RoHS:否 类别:集成电路 (IC) >> 时钟/计时 - 时钟发生器，PLL，频率合成器 系列:- 标准包装:39 系列:- 类型:* PLL:带旁路 输入:时钟 输出:时钟 电路数:1 比率 - 输入:输出:1:10 差分 - 输入:输出:是/是 频率 - 最大:170MHz 除法器/乘法器:无/无 电源电压:2.375 V ~ 3.465 V 工作温度:0°C ~ 70°C 安装类型:* 封装/外壳:* 供应商设备封装:* 包装:* |
| IDT5T9821NLGI | 功能描述:IC CLK DRIVER ZD PLL 68-VFQFPN RoHS:是 类别:集成电路 (IC) >> 时钟/计时 - 时钟发生器，PLL，频率合成器 系列:- 标准包装:39 系列:- 类型:* PLL:带旁路 输入:时钟 输出:时钟 电路数:1 比率 - 输入:输出:1:10 差分 - 输入:输出:是/是 频率 - 最大:170MHz 除法器/乘法器:无/无 电源电压:2.375 V ~ 3.465 V 工作温度:0°C ~ 70°C 安装类型:* 封装/外壳:* 供应商设备封装:* 包装:* |
| IDT5T9821NLGI8 | 功能描述:IC CLK DRIVER ZD PLL 68-VFQFPN RoHS:是 类别:集成电路 (IC) >> 时钟/计时 - 时钟发生器，PLL，频率合成器 系列:- 标准包装:39 系列:- 类型:* PLL:带旁路 输入:时钟 输出:时钟 电路数:1 比率 - 输入:输出:1:10 差分 - 输入:输出:是/是 频率 - 最大:170MHz 除法器/乘法器:无/无 电源电压:2.375 V ~ 3.465 V 工作温度:0°C ~ 70°C 安装类型:* 封装/外壳:* 供应商设备封装:* 包装:* |
发布紧急采购，3分钟左右您将得到回复。