- 您现在的位置：买卖IC网 > PDF目录9951 > IDT72T1865L5BB (IDT, Integrated Device Technology Inc)IC FIFO 8192X18 5NS 144BGA PDF资料下载
参数资料
| 型号： | IDT72T1865L5BB |
| 厂商： | IDT, Integrated Device Technology Inc |
| 文件页数： | 17/55页 |
| 文件大小： | 0K |
| 描述： | IC FIFO 8192X18 5NS 144BGA |
| 标准包装： | 1 |
| 系列： | 72T |
| 功能： | 异步，双端口 |
| 存储容量： | 144K（8K x 18） |
| 数据速率： | 10MHz |
| 访问时间： | 5ns |
| 电源电压： | 2.375 V ~ 2.625 V |
| 工作温度： | 0°C ~ 70°C |
| 安装类型： | 表面贴装 |
| 封装/外壳： | 144-BGA |
| 供应商设备封装： | 144-PBGA（13x13） |
| 包装： | 托盘 |
| 其它名称： | 72T1865L5BB |
第1页第2页第3页第4页第5页第6页第7页第8页第9页第10页第11页第12页第13页第14页第15页第16页当前第17页第18页第19页第20页第21页第22页第23页第24页第25页第26页第27页第28页第29页第30页第31页第32页第33页第34页第35页第36页第37页第38页第39页第40页第41页第42页第43页第44页第45页第46页第47页第48页第49页第50页第51页第52页第53页第54页第55页
24
COMMERCIALANDINDUSTRIAL
TEMPERATURERANGES
IDT72T1845/55/65/75/85/95/105/115/125 2.5V TeraSync 18-BIT/9-BIT FIFO 2Kx18/4Kx9, 4Kx18/
8Kx9, 8Kx18/16Kx9, 16Kx18/32Kx9, 32Kx18/64Kx9, 64Kx18/128Kx9, 128Kx18/256Kx9, 256Kx18/512Kx9, 512Kx18/1Mx9
FEBRUARY 10, 2009
The MARK input must remain HIGH during the whole period of retransmit
mode, a falling edge of RCLK while MARK is LOW will take the device out of
retransmitmodeandintonormalmode.AnynumberofMARKlocationscanbe
set during FIFO operation, only the last marked location taking effect. Once a
mark location has been set the write pointer cannot be incremented past this
marked location. During retransmit mode write operations to the device may
continue without hindrance.
FIRST WORD FALL THROUGH/SERIAL IN (FWFT/SI)
This is a dual purpose pin. During Master Reset, the state of the FWFT/
SI input determines whether the device will operate in IDT Standard mode or
First Word Fall Through (FWFT) mode.
If, at the time of Master Reset, FWFT/SI is LOW, then IDT Standard mode
will be selected. This mode uses the Empty Flag (
EF) to indicate whether or
not there are any words present in the FIFO memory. It also uses the Full Flag
function (
FF) to indicate whether or not the FIFO memory has any free space
for writing. In IDT Standard mode, every word read from the FIFO, including
the first, must be requested using the Read Enable (
REN) and RCLK.
If, at the time of Master Reset, FWFT/SI is HIGH, then FWFT mode will be
selected. This mode uses Output Ready (
OR)toindicatewhetherornotthere
is valid data at the data outputs (Qn). It also uses Input Ready (
IR) to indicate
whether or not the FIFO memory has any free space for writing. In the FWFT
mode,thefirstwordwrittentoanemptyFIFOgoesdirectlytoQnafterthreeRCLK
rising edges,
REN = LOW is not necessary. Subsequent words must be
accessed using the Read Enable (
REN) and RCLK.
AfterMasterReset,FWFT/SIactsasaserialinputforloading
PAEandPAF
offsets into the programmable registers. The serial input function can only be
used when the serial loading method has been selected during Master Reset.
SerialprogrammingusingtheFWFT/SIpinfunctionsthesamewayinbothIDT
Standard and FWFT modes.
WRITE STROBE & WRITE CLOCK (WR/WCLK)
IfSynchronousoperationofthewriteporthasbeenselectedvia
ASYW,this
input behaves as WCLK.
A write cycle is initiated on the rising edge of the WCLK input. Data setup
and hold times must be met with respect to the LOW-to-HIGH transition of the
WCLK.ItispermissibletostoptheWCLK. NotethatwhileWCLKisidle,the
FF/
IR, PAF and HF flags will not be updated. (Note that WCLK is only capable of
updating
HF flag to LOW). The Write and Read Clocks can either be
independent or coincident.
IfAsynchronousoperationhasbeenselectedthisinputisWR(writestrobe).
Data is Asynchronously written into the FIFO via the Dn inputs whenever there
is a rising edge on WR. In this mode the WEN input must be tied LOW.
WRITE ENABLE (
WEN)
Whenthe
WENinput isLOW,datamaybeloadedintotheFIFORAMarray
on the rising edge of every WCLK cycle if the device is not full. Data is stored
in the RAM array sequentially and independently of any ongoing read
operation.
When
WENisHIGH,nonewdataiswrittenintheRAMarrayoneachWCLK
cycle.
To prevent data overflow in the IDT Standard mode,
FF will go LOW,
inhibiting further write operations. Upon the completion of a valid read cycle,
FF will go HIGH allowing a write to occur. The FF is updated by two WCLK
cycles + tSKEW after the RCLK cycle.
To prevent data overflow in the FWFT mode,
IR will go HIGH, inhibiting
further write operations. Upon the completion of a valid read cycle,
IR will go
LOW allowing a write to occur. The
IR flag is updated by two WCLK cycles +
tSKEW after the valid RCLK cycle.
WENisignoredwhentheFIFOisfullineitherFWFTorIDTStandardmode.
If Asynchronous operation of the write port has been selected, then WEN
must be held active, (tied LOW).
READ STROBE & READ CLOCK (RD/RCLK)
IfSynchronousoperationofthereadporthasbeenselectedvia
ASYR,this
inputbehavesasRCLK.A readcycleisinitiatedontherisingedgeoftheRCLK
input. Data can be read on the outputs, on the rising edge of the RCLK input.
ItispermissibletostoptheRCLK. NotethatwhileRCLKisidle,the
EF/OR,PAE
and
HFflagswillnotbeupdated.(NotethatRCLKisonlycapableofupdating
the
HF flag to HIGH). The Write and Read Clocks can be independent or
coincident.
If Asynchronous operation has been selected this input is RD (Read
Strobe) . Data is Asynchronously read from the FIFO via the output register
whenever there is a rising edge on RD. In this mode the
REN andRCSinputs
mustbetiedLOW.The
OEinputisusedtoprovideAsynchronouscontrolofthe
three-stateQnoutputs.
WRITE CHIP SELECT (
WCS)
The
WCS disables all Write Port inputs (data only) if it is held HIGH. To
perform normal operations on the write port, the
WCS must be enabled, held
LOW.
READ ENABLE (
REN)
When Read Enable is LOW, data is loaded from the RAM array into the
outputregisterontherisingedgeofeveryRCLKcycleifthedeviceisnotempty.
When the
REN input is HIGH, the output register holds the previous data
and no new data is loaded into the output register. The data outputs Q0-Qn
maintain the previous data value.
In the IDT Standard mode, every word accessed at Qn, including the first
word written to an empty FIFO, must be requested using
REN provided that
RCSisLOW. WhenthelastwordhasbeenreadfromtheFIFO,theEmptyFlag
(
EF)willgoLOW,inhibitingfurtherreadoperations. RENisignoredwhenthe
FIFO is empty. Once a write is performed,
EF will go HIGH allowing a read to
occur. The
EFflagisupdatedbytwoRCLKcycles+tSKEW afterthevalidWCLK
cycle. Both
RCS andREN must be active, LOW for data to be read out on the
rising edge of RCLK.
IntheFWFTmode,thefirstwordwrittentoanemptyFIFOautomaticallygoes
to the outputs Qn, on the third valid LOW-to-HIGH transition of RCLK + tSKEW
after the first write.
RENandRCSdonotneedtobeassertedLOWfortheFirst
Word to fall through to the output register. In order to access all other words,
a read must be executed using
REN and RCS. The RCLK LOW-to-HIGH
transition after the last word has been read from the FIFO, Output Ready (
OR)
will go HIGH with a true read (RCLK with
REN=LOW;RCS=LOW),inhibiting
further read operations.
REN is ignored when the FIFO is empty.
If Asynchronous operation of the Read port has been selected, then
REN
must be held active, (tied LOW).
SERIAL ENABLE (
SEN )
The
SENinput isanenableusedonlyforserialprogrammingoftheoffset
registers. The serial programming method must be selected during Master
Reset.
SENisalwaysusedinconjunctionwithLD. Whentheselinesareboth
LOW,dataattheSIinputcanbeloadedintotheprogramregisteronebitforeach
LOW-to-HIGH transition of SCLK.
When
SEN is HIGH, the programmable registers retains the previous
settings and no offsets are loaded.
SEN functions the same way in both IDT
Standard and FWFT modes.
相关PDF资料 |
PDF描述 |
|---|---|
| HIN232CBZ-T | IC 2DRVR/2RCVR RS232 5V 16-SOIC |
| HIN202IBNZ | IC 2DRVR/2RCVR RS232 5V 16-SOIC |
| VI-21K-MX-F4 | CONVERTER MOD DC/DC 40V 75W |
| IDT72V3670L15PF | IC FIFO SS 8192X36 10NS 128-TQFP |
| MS27466E11A2P | CONN RCPT 2POS WALL MT W/PINS |
相关代理商/技术参数 |
参数描述 |
|---|---|
| IDT72T1865L5BBI | 功能描述:IC FIFO 8192X18 5NS 144BGA RoHS:否 类别:集成电路 (IC) >> 逻辑 - FIFO 系列:72T 标准包装:15 系列:74F 功能:异步 存储容量:256（64 x 4） 数据速率:- 访问时间:- 电源电压:4.5 V ~ 5.5 V 工作温度:0°C ~ 70°C 安装类型:通孔 封装/外壳:24-DIP（0.300"，7.62mm） 供应商设备封装:24-PDIP 包装:管件 其它名称:74F433 |
| IDT72T1865L6-7BB | 功能描述:IC FIFO 8192X18 6-7NS 144BGA RoHS:否 类别:集成电路 (IC) >> 逻辑 - FIFO 系列:72T 标准包装:90 系列:7200 功能:同步 存储容量:288K（16K x 18） 数据速率:100MHz 访问时间:10ns 电源电压:4.5 V ~ 5.5 V 工作温度:0°C ~ 70°C 安装类型:表面贴装 封装/外壳:64-LQFP 供应商设备封装:64-TQFP（14x14） 包装:托盘 其它名称:72271LA10PF |
| IDT72T1875L4-4BB | 功能描述:IC FIFO 16384X18 2.5V 4NS 144BGA RoHS:否 类别:集成电路 (IC) >> 逻辑 - FIFO 系列:72T 标准包装:15 系列:74F 功能:异步 存储容量:256（64 x 4） 数据速率:- 访问时间:- 电源电压:4.5 V ~ 5.5 V 工作温度:0°C ~ 70°C 安装类型:通孔 封装/外壳:24-DIP（0.300"，7.62mm） 供应商设备封装:24-PDIP 包装:管件 其它名称:74F433 |
| IDT72T1875L5BB | 功能描述:IC FIFO 16384X18 2.5V 5NS 144BGA RoHS:否 类别:集成电路 (IC) >> 逻辑 - FIFO 系列:72T 标准包装:15 系列:74F 功能:异步 存储容量:256（64 x 4） 数据速率:- 访问时间:- 电源电压:4.5 V ~ 5.5 V 工作温度:0°C ~ 70°C 安装类型:通孔 封装/外壳:24-DIP（0.300"，7.62mm） 供应商设备封装:24-PDIP 包装:管件 其它名称:74F433 |
| IDT72T1875L5BBI | 功能描述:IC FIFO 16384X18 2.5V 5NS 144BGA RoHS:否 类别:集成电路 (IC) >> 逻辑 - FIFO 系列:72T 标准包装:15 系列:74F 功能:异步 存储容量:256（64 x 4） 数据速率:- 访问时间:- 电源电压:4.5 V ~ 5.5 V 工作温度:0°C ~ 70°C 安装类型:通孔 封装/外壳:24-DIP（0.300"，7.62mm） 供应商设备封装:24-PDIP 包装:管件 其它名称:74F433 |
发布紧急采购，3分钟左右您将得到回复。