- 您现在的位置：买卖IC网 > PDF目录9786 > IL3285 (NVE Corp/Isolation Products)IC TXRX RS485 ISOLATED 16SOICW PDF资料下载
参数资料
| 型号： | IL3285 |
| 厂商： | NVE Corp/Isolation Products |
| 文件页数： | 2/18页 |
| 文件大小： | 0K |
| 描述： | IC TXRX RS485 ISOLATED 16SOICW |
| 产品培训模块： | IsoLoop® Isolator |
| 标准包装： | 50 |
| 系列： | IsoLoop® |
| 类型： | 收发器，隔离式 |
| 驱动器/接收器数： | 1/1 |
| 规程： | RS485 |
| 电源电压： | 3.3V，5V |
| 安装类型： | 表面贴装 |
| 封装/外壳： | 16-SOIC（0.295"，7.50mm 宽） |
| 供应商设备封装： | * |
| 包装： | 管件 |
| 其它名称： | 390-1034-5 |
IL3285/IL3222
10
NVE Corporation
11409 Valley View Road, Eden Prairie, MN 55344-3617
Phone: (952) 829-9217
www.isoloop.com
iso-info@nve.com
NVE Corporation
Typical Coil Connections
R
RE
A
B
V
DD2
V
COIL2
V
COIL1
V
DD1
DE
D
R1
16pF ±50%
R2
R3
A
B
Z
R
RE
Y
V
COIL2
V
DD2
V
COIL1
V
DD1
DE
D
R1
R2
R3
16pF ±50%
VDD1 = VDD2 = 5 V
R1, R2, R3 = 820
VDD1 = 3.3 V
R1, R2 = 510 ; R3 = 820
VDD1 = VDD2 = 5 V
R1, R2, R3 = 820
VDD1 = 3.3 V
R1, R2 = 510 ; R3 = 820
Fail-Safe Operation
“Fail-safe operation” is defined here as the forcing of a logic high state on the “R” output in response to an open-circuit condition
between the “A” and “B” lines of the bus, or when no drivers are active on the bus.
Proper biasing can ensure fail-safe operation, that is a known state when there are no active drivers on the bus. IL3285 and IL3222
Isolated Transceivers include internal pull-up and pull-down resistors of approximately 200 k in the receiver section (RFS-INT; see
figure on following page). These internal resistors are designed to ensure failsafe operation but only if there are no termination
resistors. The entire VDD will appear between inputs “A” and “B” if there is no loading and no termination resistors, and there will
be more than the required 200 mV with up to four RS-485/RS-422 worst-case one-eighth unit loads of 96 k. Many designs
operating below 1 Mbps or less than 1,000 feet are unterminated. Termination resistors may not be necessary for very low data
rates and very short cable runs because reflections have time to settle before data sampling, which occurs at the middle of the bit
interval.
In busses with low-impedance termination resistors, however, the differential voltage across the conductor pair will be close to
zero with no active drivers. In this case the state of the bus is indeterminate, and the idle bus will be susceptible to noise. For
example, with 120 termination resistors (RT) on each end of the cable, and four eighth unit loads (96 k each), without external
fail-safe biasing resistors the internal pull-up and pull-down resistors will produce a voltage between inputs “A” and “B” of only
about one millivolt. This is not nearly enough to ensure a known state. External fail-safe biasing resistors (RFS-EXT) at one end of
the bus can ensure fail-safe operation with a terminated bus. Resistors should be selected so that under worst-case power supply
and resistor tolerances there is at least 200 mV across the conductor pair with no active drivers to meet the input sensitivity
specification of the RS-422 and RS-485 standards.
Using the same value for pull-up and pull-down biasing resistors maintains balance for positive- and negative going transitions.
Lower-value resistors increase inactive noise immunity at the expense of quiescent power consumption. Note that each Unit Load
on the bus adds a worst-case loading of 12 k across the conductor pair, and 256 one-eighth unit loads add 375 worst-case
loading. The more loads on the bus, the lower the required values of the biasing resistors.
In the example with two 120 termination resistors and four eighth unit loads, 560 external biasing resistors provide more than
200 mV between “A” and “B” with adequate margin for power supply variations and resistor tolerances. This ensures a known
state when there are no active drivers. Other illustrative examples are shown in the following table:
相关PDF资料 |
PDF描述 |
|---|---|
| LTC1747CFW#PBF | IC ADC 12BIT 80MSPS 48-TSSOP |
| MAX3443EASA+T | IC TXRX RS-485 8-SOIC |
| MS27467E21B16SB | CONN PLUG 16POS STRAIGHT W/SCKT |
| VI-2N1-IU-F2 | CONVERTER MOD DC/DC 12V 200W |
| VI-BTJ-MW-F2 | CONVERTER MOD DC/DC 36V 100W |
相关代理商/技术参数 |
参数描述 |
|---|---|
| IL3285-3E | 功能描述:TXRX ISO BUS 5MBPS RS485 16SOIC RoHS:是 类别:集成电路 (IC) >> 接口 - 驱动器，接收器，收发器 系列:IsoLoop® 标准包装:1,240 系列:GD 类型:收发器 驱动器/接收器数:3/5 规程:RS232 电源电压:4.5 V ~ 5.5 V 安装类型:通孔 封装/外壳:20-DIP（0.300"，7.62mm） 供应商设备封装:20-PDIP 包装:管件 |
| IL3285E | 功能描述:TXRX ISO BUS 1MBS RS485 16SOIC RoHS:是 类别:集成电路 (IC) >> 接口 - 驱动器，接收器，收发器 系列:IsoLoop® 产品培训模块:Lead (SnPb) Finish for COTS Obsolescence Mitigation Program 标准包装:50 系列:- 类型:收发器 驱动器/接收器数:1/1 规程:RS422，RS485 电源电压:4.75 V ~ 5.25 V 安装类型:通孔 封装/外壳:8-DIP（0.300"，7.62mm） 供应商设备封装:8-PDIP 包装:管件 产品目录页面:1402 (CN2011-ZH PDF) |
| IL3285ETR13 | 制造商:未知厂家 制造商全称:未知厂家 功能描述:Fractional Load RS485 and RS422 Transceivers |
| IL3285TR13 | 制造商:未知厂家 制造商全称:未知厂家 功能描述:Fractional Load RS485 and RS422 Transceivers |
| IL329 | 制造商:INFINEON 制造商全称:Infineon Technologies AG 功能描述:OPTICALLY COUPLED TELECOM SWITCH |
发布紧急采购，3分钟左右您将得到回复。