- 您现在的位置：买卖IC网 > Datasheet目录330 > IL711T-1E (NVE Corp/Isolation Products)ISOLATOR MAG DIGITAL 125C 8-MSOP Datasheet资料下载
参数资料
| 型号： | IL711T-1E |
| 厂商： | NVE Corp/Isolation Products |
| 文件页数： | 8/16页 |
| 文件大小： | 0K |
| 描述： | ISOLATOR MAG DIGITAL 125C 8-MSOP |
| 产品培训模块： | IsoLoop® Isolator |
| 产品目录绘图： | IL511, IL711 Circuit |
| 标准包装： | 100 |
| 系列： | IsoLoop® |
| 输入 - 1 侧/2 侧： | 2/0 |
| 通道数： | 2 |
| 电源电压： | 3 V ~ 5.5 V |
| 电压 - 隔离： | 2500Vrms |
| 数据速率： | 110Mbps |
| 传输延迟： | 12ns |
| 输出类型： | 三态 |
| 封装/外壳： | 8-TSSOP，8-MSOP（0.118"，3.00mm 宽） |
| 供应商设备封装： | 8-MSOP |
| 包装： | 管件 |
| 工作温度： | -40°C ~ 125°C |
| 产品目录页面： | 2771 (CN2011-ZH PDF) |
| 其它名称： | 390-1113 390-1113-5 390-1113-ND |
IL711/IL712/IL721
Application Information
Electrostatic Discharge Sensitivity
This product has been tested for electrostatic sensitivity to the
limits stated in the specifications. However, NVE recommends that
all integrated circuits be handled with appropriate care to avoid
damage. Damage caused by inappropriate handling or storage could
range from performance degradation to complete failure.
Electromagnetic Compatibility
IsoLoop Isolators have the lowest EMC footprint of any isolation
technology. IsoLoop Isolators’ Wheatstone bridge configuration
and differential magnetic field signaling ensure excellent EMC
performance against all relevant standards.
These isolators are fully compliant with generic EMC standards
EN50081, EN50082-1 and the umbrella line-voltage standard for
Information Technology Equipment (ITE) EN61000. NVE has
completed compliance tests in the categories below:
EN50081-1
Residential, Commercial & Light Industrial
Methods EN55022, EN55014
EN50082-2: Industrial Environment
Methods EN61000-4-2 (ESD), EN61000-4-3 (Electromagnetic
Field Immunity), EN61000-4-4 (Electrical Transient Immunity),
EN61000-4-6 (RFI Immunity), EN61000-4-8 (Power Frequency
Magnetic Field Immunity), EN61000-4-9 (Pulsed Magnetic
Field), EN61000-4-10 (Damped Oscillatory Magnetic Field)
ENV50204
Radiated Field from Digital Telephones (Immunity Test)
Immunity to external magnetic fields is even higher if the field
direction is “end-to-end” rather than to “pin-to-pin” as shown in the
diagram below:
Cross-axis Field Direction
Power Supply Decoupling
Both power supplies to these devices should be decoupled with
low-ESR 47 nF ceramic capacitors. Ground planes for both GND 1
and GND 2 are highly recommended for data rates above 10 Mbps.
Capacitors must be located as close as possible to the V DD pins.
Maintaining Creepage
Creepage distances are often critical in isolated circuits. In addition to
meeting JEDEC standards, NVE isolator packages have unique creepage
specifications. Standard pad libraries often extend under the package,
compromising creepage and clearance. Similarly, ground planes, if used,
should be spaced to avoid compromising clearance. Package drawings
and recommended pad layouts are included in this datasheet.
Signal Status on Start-up and Shut Down
To minimize power dissipation, input signals are differentiated and
then latched on the output side of the isolation barrier to reconstruct
the signal. This could result in an ambiguous output state depending
on power up, shutdown and power loss sequencing. Unless the circuit
connected to the isolator performs its own power- on reset (POR), a
start-up initialization circuit should be considered. Initialization
consists of toggling the input either high then low, or low then high.
In CAN applications, the IL712 or IL721 should be used with CAN
transceivers with Dominant Timeout functions for seamless POR. Most
CAN transceivers have Dominant Timeout options. Examples include
NXP’s TJA 1050 and TJA 1040 transceivers.
Data Transmission Rates
The reliability of a transmission system is directly related to the
accuracy and quality of the transmitted digital information. For a digital
system, those parameters which determine the limits of the data
transmission are pulse width distortion and propagation delay skew.
Propagation delay is the time taken for the signal to travel through
the device. This is usually different when sending a low-to-high
than when sending a high-to-low signal. This difference, or error, is
called pulse width distortion (PWD) and is usually in nanoseconds.
It may also be expressed as a percentage:
PWD% = Maximum Pulse Width Distortion (ns)
Signal Pulse Width (ns)
For example, with data rates of 12.5 Mbps:
x 100%
Dynamic Power Consumption
IsoLoop Isolators achieve their low power consumption from the
way they transmit data across the isolation barrier. By detecting the
edge transitions of the input logic signal and converting these to
narrow current pulses, a magnetic field is created around the GMR
Wheatstone bridge. Depending on the direction of the magnetic
field, the bridge causes the output comparator to switch following
the input logic signal. Since the current pulses are narrow, about
2.5 ns, the power consumption is independent of mark-to-space
ratio and solely dependent on frequency. This has obvious
advantages over optocouplers, which have power consumption
heavily dependent on mark-to-space ratio.
8
PWD% = 3 ns x 100% = 3.75%
80 ns
This figure is almost three times better than any available
optocoupler with the same temperature range, and two times better
than any optocoupler regardless of published temperature range.
IsoLoop isolators exceed the 10% maximum PWD recommended
by PROFIBUS, and will run to nearly 35 Mb within the 10% limit.
Propagation delay skew is the signal propagation difference between two
or more channels. This becomes significant in clocked systems because it
is undesirable for the clock pulse to arrive before the data has settled.
Propagation delay skew is especially critical in high data rate parallel
systems for establishing and maintaining accuracy and repeatability.
Worst-case channel-to-channel skew in an IL700 Isolator is just 3 ns—
ten times better than any optocoupler. IL700 Isolators have a maximum
propagation delay skew of 6 ns— five times better than any optocoupler.
NVE Corporation
11409 Valley View Road, Eden Prairie, MN 55344-3617
Phone: (952) 829-9217
Fax: (952) 829-9189
www.IsoLoop.com
?NVE Corporation
相关PDF资料 |
PDF描述 |
|---|---|
| IMEP168 | PANEL INNER 61.75X26.75" WHITE |
| IMESD168 | DOOR STEEL 62.99X31.5" BEIGE |
| IN3006CG | BATTERY CHARGER USB 2-NIMH |
| IPC1676ST | CABINET STEEL 23.6X28X70.3 |
| IPC1676 | CABINET STEEL 23.6X28X70.3 |
相关代理商/技术参数 |
参数描述 |
|---|---|
| IL711T-2E | 制造商:NVE Corporation 功能描述:Digital Isolator 制造商:NVE Corporation 功能描述:IC, DIGITAL ISOLATOR, 12NS, DIP-8; No. of Channels:2; Propagation Delay:12ns; Supply Voltage Min:3V; Supply Voltage Max:5.5V; Digital IC Case Style:DIP; No. of Pins:8; Supply Current:10A; Operating Temperature Min:-40C ;RoHS Compliant: Yes |
| IL711T-3 | 功能描述:ISOLATOR HS DIGITAL 125C 8SOIC RoHS:否 类别:隔离器 >> 数字隔离器 系列:IsoLoop® 标准包装:66 系列:iCoupler® 输入 - 1 侧/2 侧:2/2 通道数:4 电源电压:3.3V，5V 电压 - 隔离:2500Vrms 数据速率:25Mbps 传输延迟:60ns 输出类型:逻辑 封装/外壳:20-SSOP（0.209"，5.30mm 宽） 供应商设备封装:20-SSOP 包装:管件 工作温度:-40°C ~ 105°C |
| IL711T-3E | 功能描述:OPTOCOUPLER 2-CH 8-SOIC RoHS:是 类别:隔离器 >> 数字隔离器 系列:IsoLoop® 产品培训模块:IsoLoop® Isolator 标准包装:50 系列:IsoLoop® 输入 - 1 侧/2 侧:5/0 通道数:5 电源电压:3 V ~ 5.5 V 电压 - 隔离:2500Vrms 数据速率:110Mbps 传输延迟:12ns 输出类型:CMOS 封装/外壳:16-SOIC（0.154"，3.90mm 宽） 供应商设备封装:16-SOIC N 包装:管件 工作温度:-40°C ~ 85°C 其它名称:390-1053-5 |
| IL711V-1E | 功能描述:General Purpose Digital Isolator 2500Vrms 2 Channel 110Mbps 30kV/μs CMTI 8-TSSOP, 8-MSOP (0.118", 3.00mm Width) 制造商:nve corp/isolation products 系列:IsoLoop? 包装:管件 零件状态:有效 技术:GMR（大型磁阻传感） 类型:通用 隔离式电源:无 通道数:2 输入 - 输入侧 1/输入侧 2:2/0 通道类型:单向 电压 - 隔离:2500Vrms 共模瞬态抗扰度（最小值）:30kV/μs 数据速率:110Mbps 传播延迟 tpLH / tpHL（最大值）:15ns，15ns 脉宽失真（最大）:3ns 上升/下降时间（典型值）:1ns，1ns 电压 - 电源:3 V ~ 5.5 V 工作温度:-40°C ~ 100°C 封装/外壳:8-TSSOP，8-MSOP（0.118"，3.00mm 宽） 供应商器件封装:8-MSOP 标准包装:100 |
| IL711VE | 功能描述:General Purpose Digital Isolator 6000Vrms 2 Channel 110Mbps 30kV/μs CMTI 16-SOIC (0.295", 7.50mm Width) 制造商:nve corp/isolation products 系列:IsoLoop? 包装:管件 零件状态:有效 技术:GMR（大型磁阻传感） 类型:通用 隔离式电源:无 通道数:2 输入 - 输入侧 1/输入侧 2:2/0 通道类型:单向 电压 - 隔离:6000Vrms 共模瞬态抗扰度（最小值）:30kV/μs 数据速率:110Mbps 传播延迟 tpLH / tpHL（最大值）:15ns，15ns 脉宽失真（最大）:3ns 上升/下降时间（典型值）:1ns，1ns 电压 - 电源:3 V ~ 5.5 V 工作温度:-40°C ~ 125°C 封装/外壳:16-SOIC（0.295"，7.50mm 宽） 供应商器件封装:16-SOIC 标准包装:50 |
发布紧急采购，3分钟左右您将得到回复。