- 您现在的位置：买卖IC网 > PDF目录383107 > ILX128MA (Sony Corporation) 5350-pixel X 6-line CCD Linear Sensor (Color) PDF资料下载
参数资料
| 型号： | ILX128MA |
| 厂商： | Sony Corporation |
| 英文描述： | 5350-pixel X 6-line CCD Linear Sensor (Color) |
| 中文描述： | 5350像素× 6线阵CCD线性传感器（彩色） |
| 文件页数： | 13/15页 |
| 文件大小： | 170K |
| 代理商： | ILX128MA |
– 13 –
ILX128MA
Notes on Handling
1. Static charge prevention
CCD image sensors are easily damaged by static discharge. Before handling be sure to take the following
protective measures.
a) Either handle bare handed or use non-chargeable gloves, clothes or material. Also use conductive
shoes.
b) When handling directly use an earth band.
c) Install a conductive mat on the floor or working table to prevent the generation of static electricity.
d) Ionized air is recommended for discharge when handling CCD image sensors.
e) For the shipment of mounted substrates, use boxes treated for the prevention of static charges.
2) Notes on Handling CCD Packages
The following points should be observed when handling and installing plastic packages.
a) Remain within the following limits when applying static load to the package.
(1) Compressive strength: 39N/surface (Do not apply load more than 0.7mm inside the outer perimeter
of the glass portion.)
(2) Shearing strength: 29N/surface
(3) Tensile strength: 29N/surface
(4) Torsional strength: 0.9Nm
b) In addition, if a load is applied to the entire surface by a hard component, bending stress may be
generated and the package may fracture, etc., depending on the flatness of the ceramic portion.
Therefore, for installation, either use an elastic load, such as a spring plate, or an adhesive.
c) Be aware that any of the following can cause the package to crack or dust to be generated.
(1) Applying repetitive bending stress to the external leads.
(2) Applying heat to the external leads for an extended period of time with soldering iron.
(3) Rapid cooling or heating.
(4) Prying the plastic portion and ceramic portion away at a support point of the adhesive layer.
(5) Applying the metal a crash or a rub against the plastic portion.
Note that the preceding notes should also be observed when removing a component from a board after it
has already been soldered.
d) The notch of the plastic portion is used for directional index, and that can not be used for reference of
fixing. In addition, the cover glass and seal resin may overlap with the notch or ceramic may overlap
with the notch of the plastic portion.
3. Soldering
a) Make sure the package temperature does not exceed 80°C.
b) Use a grounded 30W soldering iron and solder each pin in less than 2 seconds. For repairs and remount,
cool sufficiently.
c) To dismount an image sensor, do not use solder suction equipment. When using an electric desoldering
tool, ground the controller. For the temperature control system, use a zero-cross type.
Plastic portion
Cover glass
39N
Ceramic portion
Adhesive
(1)
29N
(3)
0.9Nm
(4)
29N
(2)
相关PDF资料 |
PDF描述 |
|---|---|
| ILX137K | 10700-pixel ?6-line CCD Linear Sensor (Color) |
| ILX503 | 2048-pixel CCD Linear Image Sensor (B/W) |
| ILX503A | 2048-pixel CCD Linear Image Sensor (B/W) |
| ILX505A | 2592-pixel CCD Linear Image Sensor (B/W) |
| ILX506 | 5000-pixel CCD Linear Image Sensor (B/W) |
相关代理商/技术参数 |
参数描述 |
|---|---|
| ILX137K | 制造商:SONY 制造商全称:Sony Corporation 功能描述:10700-pixel ?6-line CCD Linear Sensor (Color) |
| ILX146K | 制造商:未知厂家 制造商全称:未知厂家 功能描述:The Industrys First Digital Copier CCD Linear Sensor with RGB Adjacent 3-Line Plus Monochrome 1-Line 7600-Pixel Sensors |
| ILX207DW | 制造商:INTEGRAL 制造商全称:INTEGRAL 功能描述:Interface IC of data serial transfer with one supply voltage |
| ILX208DW | 制造商:INTEGRAL 制造商全称:INTEGRAL 功能描述:Interface IC of data serial transfer with one supply voltage |
| ILX232 | 制造商:INTEGRAL 制造商全称:INTEGRAL 功能描述:Interface transceiver of RS-232 standard with one supply voltage |
发布紧急采购，3分钟左右您将得到回复。