- 您现在的位置：买卖IC网 > PDF目录383107 > ILX511 (Sony Corporation) 2048-pixel CCD Linear Image Sensor (B/W) PDF资料下载
参数资料
| 型号： | ILX511 |
| 厂商： | Sony Corporation |
| 英文描述： | 2048-pixel CCD Linear Image Sensor (B/W) |
| 中文描述： | 2048像素CCD线性图像传感器（黑/白） |
| 文件页数： | 11/13页 |
| 文件大小： | 145K |
| 代理商： | ILX511 |
—11—
ILX511
Notes on Handling
1) Static charge prevention
CCD image sensors are easily damaged by static discharge. Before handling, be sure to take the following
protective measures.
a) Either handle bare handed or use non-chargeable gloves, clothes or material. Also use conductive
shoes.
b) When handling directly use an earth band.
c) Install a conductive mat on the floor or working table to prevent the generation of static electricity.
d) Ionized air is recommended for discharge when handling CCD image sensors.
e) For the shipment of mounted substrates use cartons treated for the prevention of static charges.
2) Notes on handling CCD Cer-DIP package
The following points should be observed when handling and installing this package.
a) (1) Compressive strength:
39N/surface
(Do not apply any load more than 0.7 mm inside the outer perimeter of the glass
portion.)
(2) Shearing strength:
29N/surface
(3) Tensile strength:
29N/surface
(4) Torsional strength:
0.9Nm
b) In addition, if a load is applied to the entire surface by a hard component, bending stress may be
generated and the package may fracture, etc., depending on the flatness of the ceramic portion.
Therefore, for installation, either use an elastic load, such as a spring plate, or an adhesive.
c) Be aware that any of the following can cause the glass to crack because the upper and lower ceramic
layers are shielded by low-melting glass.
(1) Applying repetitive bending stress to the external leads.
(2) Applying heat to the external leads for an extended period of time with a soldering iron.
(3) Rapid cooling or heating.
(4) Applying a load or impact to a limited portion of the low-melting glass with a small-tipped tool such
as tweezers.
(5) Prying the upper or lower ceramic layers away at a support point of the low-melting glass.
Note that the preceding notes should also be observed when removing a component from a board
after it has already been soldered.
3) Soldering
a) Make sure the package temperature does not exceed 80 °C.
b) Solder dipping in a mounting furnace causes damage to the glass and other defects. Use a grounded
30W soldering iron and solder each pin in less than 2 seconds. For repairs and remount, cool
sufficiently.
c) To dismount image sensors, do not use a solder suction equipment. When using an electric
desoldering tool, ground the controller. For the control system, use a zero cross type.
Upper ceramic layer
Lower ceramic layer
Low-melting glass
39N
(1)
(4)
(3)
(2)
29N
29N
0.9Nm
相关PDF资料 |
PDF描述 |
|---|---|
| ILX512 | 7500-Pixel CCD Linear Sensor (B/W)(7500-像素CCD线性传感器(黑白)) |
| ILX514 | 3918-pixel CCD Linear Image Sensor (B/W) |
| ILX516K | 3648 X 3pixel CCD Linear Sensor (Color) |
| ILX518 | 5363-pixel X 3 line CCD Linear Sensor (Color) |
| ILX518K | 5363-pixel X 3 line CCD Linear Sensor (Color) |
相关代理商/技术参数 |
参数描述 |
|---|---|
| ILX514 | 制造商:SONY 制造商全称:Sony Corporation 功能描述:3918-pixel CCD Linear Image Sensor (B/W) |
| ILX516K | 制造商:SONY 制造商全称:Sony Corporation 功能描述:3648 X 3pixel CCD Linear Sensor (Color) |
| ILX518 | 制造商:SONY 制造商全称:Sony Corporation 功能描述:5363-pixel X 3 line CCD Linear Sensor (Color) |
| ILX518K | 制造商:SONY 制造商全称:Sony Corporation 功能描述:5363-pixel X 3 line CCD Linear Sensor (Color) |
| ILX520K | 制造商:SONY 制造商全称:Sony Corporation 功能描述:7078 X 3pixel CCD Linear Sensor (Color) |
发布紧急采购，3分钟左右您将得到回复。