- 您现在的位置：买卖IC网 > PDF目录383107 > ILX522K (Sony Corporation) 2048 X 2pixel CCD Linear Sensor (Color) PDF资料下载
参数资料
| 型号： | ILX522K |
| 厂商： | Sony Corporation |
| 英文描述： | 2048 X 2pixel CCD Linear Sensor (Color) |
| 中文描述： | 2048 × 2pixel防治荒漠化公约线性传感器（彩色） |
| 文件页数： | 10/12页 |
| 文件大小： | 180K |
| 代理商： | ILX522K |
– 10 –
ILX522K
Notes of Handling
1) Static charge prevention
CCD image sensors are easily damaged by static discharge. Before handling be sure to take the following
protective measures.
a) Either handle bare handed or use non chargeable gloves, clothes or material. Also use conductive
shoes.
b) When handling directly use an earth band.
c) Install a conductive mat on the floor or working table to prevent the generation of static electricity.
d) lonized air is recommended for discharge when handling CCD image sensor.
e) For the shipment of mounted substrates, use boxes treated for prevention of static charges.
2) Notes on Handling CCD Cer-DlP Packages
The following points should be observed when handling and installing cer-DlP packages.
a) Remain within the following limits when applying static load to the ceramic portion of the package:
(1) Compressive strength: 39 N/surface (Do not apply load more than 0.7mm inside the outer
perimeter of the glass portion.)
(2) Shearing strength: 29 N/surface
(3) Tensile strength: 29 N/surface
(4) Torsional strength: 0.9 Nm
Upper ceramic layer
Lower ceramic layer
AAAAA
39N
Low-melting glass
(1)
AAAAAAAAA
AAAAA
(2)
29N
29N
AAAA
AAAA
0.9Nm
b) In addition, if a load is applied to the entire surface by a hard component, bending stress may be
generated and the package may fracture, etc., depending on the flatness of the ceramic portion.
Therefore, for installation, either use an elastic load, such as a spring plate, or an adhesive.
c) Be aware that any of the following can cause the glass to crack: because the upper and lower ceramic
layers are shielded by low-melting glass,
(1) Applying repetitive bending stress to the external leads.
(2) Applying heat to the external leads for an extended period of time with soldering iron.
(3) Rapid cooling or heating
(4) Rapid cooling or impact to a limited portion of the low-melting glass with a small-tipped tool such as
tweezers.
(5) Prying the upper or lower ceramic layers away at a support point of the low-melting glass.
Note that the preceding notes should also be observed when removing a component from a board after
it has already been soldered.
3) Soldering
a) Make sure the package temperature does not exceed 80°C.
b) Solder dipping in a mounting furnace causes damage to the glass and other defects. Use a grounded
30W soldering iron and solder each pin in less then 2 seconds. For repairs and remount, cool
sufficiently.
c) To dismount an imaging device, do not use a solder suction equipment. When using an electric
desoldering tool, ground the controller. For the control system, use a zero cross type.
相关PDF资料 |
PDF描述 |
|---|---|
| ILX523A | 2700 pixel CCD Linear Sensor (B/W) |
| ILX524K | 2700 × 3Pixel CCD Linear Sensor (Color)(2700 × 3-像素CCD线性传感器(彩色)) |
| ILX524 | 2700 X 3pixel CCD Linear Sensor (Color) |
| ILX524KA | 2700 pixel X 3 line CCD Linear Sensor (Color) |
| ILX526A | 3000-pixel CCD Linear Image Sensor (B/W) |
相关代理商/技术参数 |
参数描述 |
|---|---|
| ILX523A | 制造商:SONY 制造商全称:Sony Corporation 功能描述:2700 pixel CCD Linear Sensor (B/W) |
| ILX524 | 制造商:SONY 制造商全称:Sony Corporation 功能描述:2700 pixel X 3 line CCD Linear Sensor (Color) |
| ILX524K | 制造商:SONY 制造商全称:Sony Corporation 功能描述:2700 X 3pixel CCD Linear Sensor (Color) |
| ILX524KA | 制造商:SONY 制造商全称:Sony Corporation 功能描述:2700 pixel X 3 line CCD Linear Sensor (Color) |
| ILX526A | 制造商:SONY 制造商全称:Sony Corporation 功能描述:3000-pixel CCD Linear Image Sensor (B/W) |
发布紧急采购，3分钟左右您将得到回复。