参数资料
| 型号： | IMS82C55AZ |
| 厂商： | Intersil |
| 文件页数： | 26/26页 |
| 文件大小： | 0K |
| 描述： | IC I/O EXPANDER 24B 44PLCC |
| 标准包装： | 260 |
| 接口： | 可编程 |
| 输入/输出数： | 24 |
| 中断输出： | 无 |
| 电源电压： | 4.5 V ~ 5.5 V |
| 工作温度： | -40°C ~ 85°C |
| 安装类型： | 表面贴装 |
| 封装/外壳： | 44-LCC（J 形引线） |
| 供应商设备封装： | 44-PLCC |
| 包装： | 管件 |
9
FN6140.2
June 15, 2006
Operating Modes
Mode 1 - (Strobed Input/Output). This functional configuration
provides a means for transferring I/O data to or from a specified
port in conjunction with strobes or “hand shaking” signals. In
mode 1, port A and port B use the lines on port C to generate or
accept these “hand shaking” signals.
Mode 1 Basic Function Definitions:
Two Groups (Group A and Group B)
Each group contains one 8-bit port and one 4-bit control/data
port
The 8-bit data port can be either input or output. Both inputs
and outputs are latched.
The 4-bit port is used for control and status of the 8-bit port.
Input Control Signal Definition
(Figures 6 and 7)
STB (Strobe Input)
A “low” on this input loads data into the input latch.
IBF (Input Buffer Full F/F)
A “high” on this output indicates that the data has been loaded
into the input latch: in essence, an acknowledgment. IBF is set
by STB input being low and is reset by the rising edge of the
RD input.
INTR (Interrupt Request)
A “high” on this output can be used to interrupt the CPU when
an input device is requesting service. INTR is set by the
condition: STB is a “one”, IBF is a “one” and INTE is a “one”. It
is reset by the falling edge of RD. This procedure allows an
input device to request service from the CPU by simply strobing
its data into the port.
INTE A
Controlled by bit set/reset of PC4.
INTE B
Controlled by bit set/reset of PC2.
Output Control Signal Definition
(Figure 8 and 9)
OBF - (Output Buffer Full F/F). The OBF output will go “low”
to indicate that the CPU has written data out to the specified
port. This does not mean valid data is sent out of the port at this
time since OBF can go true before data is available. Data is
guaranteed valid at the rising edge of OBF, (See Note 1). The
OBF F/F will be set by the rising edge of the WR input and reset
by ACK input being low.
CONTROL WORD #13
CONTROL WORD #15
Mode 0 Configurations (Continued)
1
D7
0
D6
0
D5
1
D4
1
D3
0
D2
0
D1
1
D0
8
PA7 - PA0
4
PC7 - PC4
4
PC3 - PC0
8
PB7 - PB0
D7 - D0
82C55A
A
B
C
1
D7
0
D6
0
D5
1
D4
1
D3
0
D2
1
D1
1
D0
8
PA7 - PA0
4
PC7 - PC4
4
PC3 - PC0
8
PB7 - PB0
D7 - D0
82C55A
A
B
C
MS82C55A, MQ82C55A, MP82C55A
相关PDF资料 |
PDF描述 |
|---|---|
| ATMEGA8535L-8JUR | MCU AVR 8K FLASH 8MHZ 44PLCC |
| IP82C55AZ | IC I/O EXPANDER 24B 40DIP |
| CS82C55A96 | IC I/O EXPANDER 24B 44PLCC |
| IS82C55A-5Z96 | IC I/O EXPANDER 24B 44PLCC |
| ATMEGA8535-16AUR | MCU AVR 8K FLASH 16MHZ 44TQFP |
相关代理商/技术参数 |
参数描述 |
|---|---|
| IMS82C55AZ96 | 功能描述:外围驱动器与原件 - PCI PERI PRG-I/O 5V 8MHZ 44PLCC INDOKI PARTPL RoHS:否 制造商:PLX Technology 工作电源电压: 最大工作温度: 安装风格:SMD/SMT 封装 / 箱体:FCBGA-1156 封装:Tray |
| IMSA100-G17M | 制造商:未知厂家 制造商全称:未知厂家 功能描述:Digital Filter |
| IMSA100-G21I | 制造商:未知厂家 制造商全称:未知厂家 功能描述:Digital Filter |
| IMSA100-G21M | 制造商:未知厂家 制造商全称:未知厂家 功能描述:Digital Filter |
| IMSA100-G21S | 制造商:未知厂家 制造商全称:未知厂家 功能描述:Digital Filter |
发布紧急采购，3分钟左右您将得到回复。