- 您现在的位置：买卖IC网 > PDF目录377498 > IR2166S (International Rectifier) PFC & BALLAST CONTROL IC PDF资料下载
参数资料
| 型号： | IR2166S |
| 厂商： | International Rectifier |
| 元件分类： | 基准电压源/电流源 |
| 英文描述： | PFC & BALLAST CONTROL IC |
| 中文描述： | 功率因数校正 |
| 文件页数： | 21/29页 |
| 文件大小： | 371K |
| 代理商： | IR2166S |
第1页第2页第3页第4页第5页第6页第7页第8页第9页第10页第11页第12页第13页第14页第15页第16页第17页第18页第19页第20页当前第21页第22页第23页第24页第25页第26页第27页第28页第29页
IR2166
www.irf.com
21
Ignition Mode (IGN)
The ignition mode is defined as the state the IC
is in when a high voltage is being established
across the lamp necessary for igniting the lamp.
The IR2166 enters ignition mode when the
voltage on pin CPH exceeds 10V.
Pin CPH is connected internally to the gate of a
P-channel MOSFET (S4) (see Figure 4) that
connects pin RPH with pin RT. As pin CPH
exceeds 10V, the gate-to-source voltage of
MOSFET S4 begins to fall below the turn-on
threshold of S4. As pin CPH continues to ramp
towards VCC, switch S4 turns off slowly. This
results in resistor RPH being disconnected
smoothly from resistor RT, which causes the
operating frequency to ramp smoothly from the
preheat frequency, through the ignition frequency,
to the final run frequency. The over-current
threshold on pin CS will protect the ballast
against a non-strike or open-filament lamp fault
condition. The voltage on pin CS is defined by
the lower half-bridge MOSFET current flowing
through the external current sensing resistor
RCS. The resistor RCS therefore programs the
maximum allowable peak ignition current (and
therefore peak ignition voltage) of the ballast
output stage. If the number of over current pulses
exceed 25, the IC will enter fault mode and gate
driver outputs HO, LO and PFC will be latched
low.
Run Mode (RUN)
Once the lamp has successfully ignited, the
ballast enters run mode. The run mode is defined
as the state the IC is in when the lamp arc is
established and the lamp is being driven to a
given power level. The run mode oscillating
frequency is determined by the timing resistor
RT and timing capacitor CT (see Design
Equations, page 26, Equations 3 and 4). Should
hard-switching occur at the half-bridge at any
time due to an open-filament or lamp removal,
the voltage across the current sensing resistor,
RCS, will exceed the internal threshold of 1.3 volts
and the IC will enter FAULT mode and gate driver
outputs HO, LO and PFC will be latched low.
DC Bus Under-voltage Reset
Should the DC bus decrease too low during a
brownout line condition or overload condition,
the resonant output stage to the lamp can shift
near or below resonance. This can produce
hard-switching at the half-bridge which can
damage the half-bridge switches or, the DC bus
can decrease too far and the lamp can
extinguish. To protect against this, the VBUS pin
includes a 3.0V under-voltage threshold. Should
the voltage at the VBUS pin decrease below 3.0V,
VCC will be discharged to the UVLO- threshold
and all gate driver outputs will be latched low.
For proper ballast design, the designer should
design the PFC section such that the DC bus
does not drop until the AC line input voltage falls
below the rated input voltage of the ballast (See
PFC section). When correctly designed, the
voltage measured at the VBUS pin will decrease
below the internal 3.0V threshold and the ballast
will turn off cleanly. The pull-up resistor to VCC
(RSUPPLY) will then turn the ballast on again
with the AC input line voltage increasing to the
minimum specified value causing VCC to exceed
UVLO+.
R
SUPPLY
should be set to turn the ballast on at
the minimum specified ballast input voltage. The
PFC should then be designed such that the DC
bus decreases at an input line voltage that is
相关PDF资料 |
PDF描述 |
|---|---|
| IR2167 | PFC BALLAST CONTROL IC |
| IR2167S | PFC Ballast Control. Thermal Overload Protection. Brown Out Protection. Programmable Preheat and Frequency. Programmable Deadtime in a 20 Lead SOIC package |
| IR2170 | OVER CURRENT SENSING IC |
| IR2170S | OVER CURRENT SENSING IC |
| IR2172 | LINEAR CURRENT SENSING IC |
相关代理商/技术参数 |
参数描述 |
|---|---|
| IR2166SPBF | 功能描述:功率驱动器IC PFC BALLAST CTRL IC 600V 15.6V VCC ESD RoHS:否 制造商:Micrel 产品:MOSFET Gate Drivers 类型:Low Cost High or Low Side MOSFET Driver 上升时间: 下降时间: 电源电压-最大:30 V 电源电压-最小:2.75 V 电源电流: 最大功率耗散: 最大工作温度:+ 85 C 安装风格:SMD/SMT 封装 / 箱体:SOIC-8 封装:Tube |
| IR2166STRPBF | 功能描述:功率驱动器IC PFC Ballast Cntrl RoHS:否 制造商:Micrel 产品:MOSFET Gate Drivers 类型:Low Cost High or Low Side MOSFET Driver 上升时间: 下降时间: 电源电压-最大:30 V 电源电压-最小:2.75 V 电源电流: 最大功率耗散: 最大工作温度:+ 85 C 安装风格:SMD/SMT 封装 / 箱体:SOIC-8 封装:Tube |
| IR2167 | 制造商:IRF 制造商全称:International Rectifier 功能描述:PFC BALLAST CONTROL IC |
| IR2167PBF | 功能描述:IC PFC BALLAST CTLR 20DIP RoHS:是 类别:集成电路 (IC) >> PMIC - 照明，镇流器控制器 系列:- 产品培训模块:Lead (SnPb) Finish for COTS Obsolescence Mitigation Program 标准包装:2,500 系列:- 类型:CCFL 控制器 频率:40 ~ 80 kHz 电流 - 电源:5mA 电流 - 输出:- 电源电压:4.5 V ~ 5.5 V 工作温度:-40°C ~ 85°C 封装/外壳:16-SOIC（0.154"，3.90mm 宽） 供应商设备封装:16-SOIC 包装:带卷 (TR) 其它名称:90-3991V+V01 |
| IR2167S | 功能描述:IC CNTRLR BALLAST PFC 20-SOIC RoHS:否 类别:集成电路 (IC) >> PMIC - 照明，镇流器控制器 系列:- 产品培训模块:Lead (SnPb) Finish for COTS Obsolescence Mitigation Program 标准包装:2,500 系列:- 类型:CCFL 控制器 频率:40 ~ 80 kHz 电流 - 电源:5mA 电流 - 输出:- 电源电压:4.5 V ~ 5.5 V 工作温度:-40°C ~ 85°C 封装/外壳:16-SOIC（0.154"，3.90mm 宽） 供应商设备封装:16-SOIC 包装:带卷 (TR) 其它名称:90-3991V+V01 |
发布紧急采购，3分钟左右您将得到回复。