- 您现在的位置：买卖IC网 > PDF目录1221 > IRDCIP2003A-C (International Rectifier)KIT DESIGN 4PH 160A 1MHZ IP2003A PDF资料下载
参数资料
| 型号： | IRDCIP2003A-C |
| 厂商： | International Rectifier |
| 文件页数： | 1/8页 |
| 文件大小： | 0K |
| 描述： | KIT DESIGN 4PH 160A 1MHZ IP2003A |
| 标准包装： | 1 |
R E F E R E N C E D E S I G N IRDCiP2003A-C
International Rectifier ? 233 Kansas Street, El Segundo, CA 90245 USA
IRDCiP2003A-C: 1MHz, 160A, Synchronous Buck
Converter Using iP2003A
Overview
This reference design is capable of delivering up to a current of
160A with the enclosed heatsink attached at an ambient
temperature of 60oC with 400LFM or an ambient temperature of
45oC with 200LFM of airflow. Performance graphs and waveforms
are provided in figures 1–9. The figures and table in pages 5 – 8
are provided as a reference design to enable engineers to very
quickly and easily design a 4-phase converter. Refer to the data
sheet for the controller listed in the bill of materials in order to
optimize this design to your specific requirements. A variety of other
controllers may also be used, but the design will require layout and
control circuit modifications.
Demoboard Quick Start Guide
Initial Settings:
The output is set to 1.3V, but can be adjusted from 0.8V to 3.3V by changing the voltage divider values of R3 and R32 according
to the following formula:
R3 = R32 = (24.9k x 0.8) / (VOUT - 0.8)
The switching frequency per phase is set to 1MHz with the frequency set resistor R4. This creates an effective output frequency of
4MHz. The graph in figure 11 shows the relationship between R4 and the switching frequency per phase. The frequency may be
adjusted by changing R4 as indicated; however, extreme changes from the 1MHz set point may require redesigning the control
loop and adjusting the values of input and output capacitors. Refer to the SOA graph in the iP2003A datasheet for maximum
operating current at different conditions.
Procedure for Connecting and Powering Up Demoboard:
1. Apply input voltage across (+12V) across VIN and PGND.
2. Apply load across VOUT pads and PGND pads.
3. Adjust load to desired level. See recommendations below.
IRDCiP2003A-C Recommended Operating Conditions
(refer to the iP2003A datasheet for maximum operating conditions)
Input voltage: 5V - 12V
1
Note: If Vin = 5V, then connect Vin to test point TP3 and Terminal T1 and remove jumper J1. Refer to schematic for details.
Output voltage: 0.8 - 3.3V
Switching Freq: 1MHz per phase, 4MHz effective output frequency.
Output current: This reference design is capable of delivering up to 160A with the enclosed heatsink attached, at an
ambient temperature of 60oC with 400LFM of airflow, or an ambient temperature of 45oC with 200LFM of
airflow.
1
Additionally, the threshold of the POR circuit should be adjusted to allow the supply to sequence properly.
12/03/04
相关PDF资料 |
PDF描述 |
|---|---|
| IRMCS2031 | SYSTEM DEVEL IMOTION SENSORLESS |
| IRMCS2033 | DESIGN BOARD FOR IRMCK203 |
| IRMCS3041 | KIT REF DES MOTION CTRL IRMCF341 |
| IRMD22141SS | KIT DESIGN EVAL BOARD/IR22141SS |
| IRMD22381Q | BOARD DEMO IR22381Q MOTOR DRIVER |
相关代理商/技术参数 |
参数描述 |
|---|---|
| IRDCIP2005A-A | 功能描述:电源管理IC开发工具 1MHZ 65A DC 80A PEAK DUAL PHASE SYNC RoHS:否 制造商:Maxim Integrated 产品:Evaluation Kits 类型:Battery Management 工具用于评估:MAX17710GB 输入电压: 输出电压:1.8 V |
| IRDCIP2005C-1 | 功能描述:电源管理IC开发工具 500KHZ 60A 1 OUTPUT IP2005C DESIGN KIT RoHS:否 制造商:Maxim Integrated 产品:Evaluation Kits 类型:Battery Management 工具用于评估:MAX17710GB 输入电压: 输出电压:1.8 V |
| IRDCIP2005C-2 | 功能描述:电源管理IC开发工具 500KHZ 50A DUAL IP2005C DESIGN KIT RoHS:否 制造商:Maxim Integrated 产品:Evaluation Kits 类型:Battery Management 工具用于评估:MAX17710GB 输入电压: 输出电压:1.8 V |
| IRDCIP2021C-1 | 功能描述:电源管理IC开发工具 500KHZ 40A 1 OUTPUT IR3623 REF BRD RoHS:否 制造商:Maxim Integrated 产品:Evaluation Kits 类型:Battery Management 工具用于评估:MAX17710GB 输入电压: 输出电压:1.8 V |
| IRDCIP2021C-2 | 功能描述:电源管理IC开发工具 500KHZ 20A DUAL IR3623 REF BRD RoHS:否 制造商:Maxim Integrated 产品:Evaluation Kits 类型:Battery Management 工具用于评估:MAX17710GB 输入电压: 输出电压:1.8 V |
发布紧急采购，3分钟左右您将得到回复。