- 您现在的位置：买卖IC网 > Datasheet目录332 > IRPLLED7 (International Rectifier)IC MOSFET DRIVER Datasheet资料下载
参数资料
| 型号： | IRPLLED7 |
| 厂商： | International Rectifier |
| 文件页数： | 14/18页 |
| 文件大小： | 0K |
| 描述： | IC MOSFET DRIVER |
| 标准包装： | 1 |
| 系列： | * |
IRS2980S
being used in dim mode place a capacitor
CDIM from the ADIM pin to COM and keep
the capacitor as close to the IC as possible
with the shortest possible traces.
4) If the IRS2980S is being used in non-dimming
mode the RAMP pin can be connected to
COM. If it is being used in dimming mode
CRAMP should be located close to the IC with
the shortest possible traces to the RAMP pin
and COM.
5) Connect IC COM to power GND at one
connection only. Do NOT route power GND
through the programming components or IC
COM.
Figure 5: LED current during dimming.
The dimming level can also be controlled from a
digital input by replacing CRAMP with a 68k
resistor. This sets a DC threshold at the RAMP
pin to approximately 1V so that a logic level PWM
dimming control signal can be applied to the ADIM
pin to directly switch the output on and off.
PCB Layout Guidelines
Proper care should be taken when laying out a
PCB board ensure correct functionality of the
IRS2980S. Transients caused by high dV/dt
during switching could potentially cause some
false triggering of the hysteretic circuit therefore a
small filter comprising RF and CF is
recommended. CF should be located close to the
IC pins with the trace from HV to RCS and the
traces from RCS to CS through RF kept as short
as possible. The 0V load return power ground
should be connected to the IC COM pin and at a
single point to avoid ground loops. The values of
RF and CF are normally chosen to provide noise
filtering without adding excessive delay to the
circuit, however in some case these are
deliberately made larger to lower the running
frequency as this reduces switching losses and
ICC current.
The following guidelines should be followed during
PCB board layout:
1) Place VCC supply decoupling capacitor
(CVCC) as close as possible to the VCC and
COM pins.
2) Place high side decoupling capacitor (CVF) as
close as possible to the HV and VS pins.
3) If the IRS2980S is being used in non-dimming
mode connect the ADIM pin to VCC. If it is
www.irf.com
14
? 2011 International Rectifier
相关PDF资料 |
PDF描述 |
|---|---|
| IRPP3637-06A | BOARD REF DESIGN POWIR+ |
| IRS2001MPBF | IC DRIVER HIGH/LOW SIDE 16MLPQ |
| IRS2001SPBF | IC DRIVER HI/LO SIDE 200V 8-SOIC |
| IRS2003STRPBF | IC DRIVER HALF-BRIDGE 8-SOIC |
| IRS2004PBF | IC DRIVER HALF-BRIDGE 8-DIP |
相关代理商/技术参数 |
参数描述 |
|---|---|
| IRPLLNR1 | 制造商:未知厂家 制造商全称:未知厂家 功能描述: |
| IRPLLNR2E | 功能描述:KIT BALLAST LINEAR INT 230VAC RoHS:否 类别:编程器，开发系统 >> 过时/停产零件编号 系列:- 标准包装:1 系列:- 类型:MCU 适用于相关产品:Freescale MC68HC908LJ/LK（80-QFP ZIF 插口） 所含物品:面板、缆线、软件、数据表和用户手册 其它名称:520-1035 |
| IRPLLNR2U | 功能描述:BALLAST 32W/T8 120V AC IR21571 RoHS:否 类别:编程器，开发系统 >> 过时/停产零件编号 系列:- 标准包装:1 系列:- 类型:MCU 适用于相关产品:Freescale MC68HC908LJ/LK（80-QFP ZIF 插口） 所含物品:面板、缆线、软件、数据表和用户手册 其它名称:520-1035 |
| IRPLLNR3 | 制造商:IRF 制造商全称:International Rectifier 功能描述:Universal Input Linear Fluorescent Ballast using the IR2167 |
| IRPLLNR4 | 功能描述:BALLAST UNIV INP FLUOR IR2166 RoHS:否 类别:编程器，开发系统 >> 过时/停产零件编号 系列:- 标准包装:1 系列:- 类型:MCU 适用于相关产品:Freescale MC68HC908LJ/LK（80-QFP ZIF 插口） 所含物品:面板、缆线、软件、数据表和用户手册 其它名称:520-1035 |
发布紧急采购，3分钟左右您将得到回复。