- 您现在的位置：买卖IC网 > PDF目录20839 > IRS2540STRPBF (International Rectifier)IC LED DRVR HP CONST CURR 8-SOIC PDF资料下载
参数资料
| 型号： | IRS2540STRPBF |
| 厂商： | International Rectifier |
| 文件页数： | 8/15页 |
| 文件大小： | 0K |
| 描述： | IC LED DRVR HP CONST CURR 8-SOIC |
| 标准包装： | 2,500 |
| 恒定电流： | 是 |
| 拓扑： | PWM，降压（降压） |
| 输出数： | 1 |
| 内部驱动器： | 是 |
| 类型 - 主要： | 通用 |
| 频率： | 500kHz |
| 电源电压： | 9 V ~ 15.6 V |
| 安装类型： | 表面贴装 |
| 封装/外壳： | 8-SOIC（0.154"，3.90mm 宽） |
| 供应商设备封装： | 8-SOIC |
| 包装： | 带卷 (TR) |
| 工作温度： | -25°C ~ 125°C |
IRS254(0,1)(S)PbF
HO
LO
Watchdog Timer
During an open circuit condition, without the
watchdog timer, the HO output would remain high at
all times and the charge stored in the bootstrap
capacitor C BOOT would gradually discharge the
floating power supply for the high-side driver, which
would then be unable to fully switch on the upper
MOSFET causing high losses. To maintain
sufficient charge on the bootstrap capacitor, a
watchdog timer has been implemented. In the
condition where V IFB remains below V IFBTH , the HO
output will be forced low after 20 μ s and the LO
output forced high. This toggling of the outputs will
last for approximately 1 μ s to maintain and replenish
sufficient charge on C BOOT .
Fig.4 Illustration of Watchdog Timer
Bootstrap Capacitor and Diode
The bootstrap capacitor value needs to be chosen
so that it maintains sufficient charge for at least the
approximately 20 μ s interval until the watchdog timer
allows the capacitor to recharge. If the capacitor
value is too small, the charge will dissipate in less
than 20 μ s. The typical bootstrap capacitor is
approximately 100 nF.
The bootstrap diode should be a fast recovery or
ultrafast recovery component to maintain good
Design Tip (DT 98-2), “Bootstrap Component
Selection For Control ICs” at www.irf.com under
Design Support
Disable (ENN) Pin
The disable pin can be used for dimming and open-
circuit protection. When the ENN pin is held low, the
chip remains in a fully functional state with no
alterations to the operating environment. To disable
the control feedback and regulation, a voltage
greater than V ENTH (approximately 2.5 V) needs to be
applied to the ENN pin. With the chip in a disabled
state, HO output will remain low, whereas the LO
output will remain high to prevent V S from floating, in
addition to maintaining charge on the bootstrap
capacitor. The threshold for disabling the
IRS254(0,1) has been set to 2.5 V to enhance
immunity to any externally generated noise, or
application ground noise. This 2.5 V threshold also
makes it ideal to receive a drive signal from a local
microcontroller.
Dimming Mode
To achieve dimming, a signal with constant
frequency and set duty cycle can be fed into the
ENN pin. There is a direct linear relationship
between the average load current and duty cycle. If
the ratio is 50%, 50% of the maximum set light
output will be realized. Likewise if the ratio is 30%,
70% of the maximum set light output will be realized.
A sufficiently high frequency of the dimming signal
must be chosen to avoid flashing or “strobe light”
effect. A signal on the order of a few kHz should be
sufficient.
The minimum amount of dimming achievable (light
output approaches 0%) will be determined by the
“on” time of the HO output, when in a fully functional
regulating state. To maintain reliable dimming, it is
recommended to keep the “off” time of the enable
signal at least 10 times that of the HO “on” time. For
example, if the application is running at 75 kHz with
an input voltage of 100 V and an output voltage of
20 V, the HO “on” time will be 3.3 μs (one-fourth of
the period – see calculations below) according to
standard buck topology theory. This will set the
minimum “off” time of the enable signal to 33 μs.
efficiency. Since the cathode of the bootstrap diode
will be switching between zero and to the high
voltage bus, the reverse recovery time of this diode
Duty Cycle =
V out
V in
? 100 =
20 V
100 V
* 100 = 20 %
is of critical importance. For additional information
concerning the bootstrap components, refer to the
www.irf.com
HO on time = 20 % * 1
75 kHz
= 3 . 3 μ s
Page 8
相关PDF资料 |
PDF描述 |
|---|---|
| P51-750-S-T-I12-4.5V-000-000 | SENSOR 750PSI 7/16-20-2B .5-4.5V |
| P51-300-S-C-M12-4.5V-000-000 | SENSOR 300PSI M12-1.5 6G .5-4.5V |
| MXHV9910B | IC LED DVR HB OFF-LINE 8-SOIC |
| 4-1624112-5 | INDUCTOR 18NH 420MA 0402 |
| EEM12DSEN-S243 | CONN EDGECARD 24POS .156 EYELET |
相关代理商/技术参数 |
参数描述 |
|---|---|
| IRS25411 | 制造商:IRF 制造商全称:International Rectifier 功能描述:LED BUCK REGULATOR CONTROL IC |
| IRS25411PBF | 功能描述:LED照明驱动器 Hysteretic Buck LED Drvr RoHS:否 制造商:STMicroelectronics 输入电压:11.5 V to 23 V 工作频率: 最大电源电流:1.7 mA 输出电流: 最大工作温度: 安装风格:SMD/SMT 封装 / 箱体:SO-16N |
| IRS25411PBF | 制造商:International Rectifier 功能描述:IC LED DRVR DIP8 |
| IRS25411SPBF | 功能描述:LED照明驱动器 600V HALF BRDG DRVR LED BUCK REGULATOR RoHS:否 制造商:STMicroelectronics 输入电压:11.5 V to 23 V 工作频率: 最大电源电流:1.7 mA 输出电流: 最大工作温度: 安装风格:SMD/SMT 封装 / 箱体:SO-16N |
| IRS25411STRPBF | 功能描述:LED照明驱动器 Hysteretic Buck LED Drvr RoHS:否 制造商:STMicroelectronics 输入电压:11.5 V to 23 V 工作频率: 最大电源电流:1.7 mA 输出电流: 最大工作温度: 安装风格:SMD/SMT 封装 / 箱体:SO-16N |
发布紧急采购，3分钟左右您将得到回复。