- 您现在的位置：买卖IC网 > PDF目录19493 > IRU1030CM (International Rectifier)IC REG LDO ADJ 3A TO-263-3 PDF资料下载
参数资料
| 型号： | IRU1030CM |
| 厂商： | International Rectifier |
| 文件页数： | 5/11页 |
| 文件大小： | 0K |
| 描述： | IC REG LDO ADJ 3A TO-263-3 |
| 标准包装： | 50 |
| 稳压器拓扑结构： | 正，可调式 |
| 输出电压： | 2.5 V ~ 3.3 V |
| 输入电压： | 最高 7V |
| 电压 - 压降（标准）： | 1.1V @ 3A |
| 稳压器数量： | 1 |
| 电流 - 输出： | 3A |
| 电流 - 限制（最小）： | 3.1A |
| 工作温度： | 0°C ~ 150°C |
| 安装类型： | 表面贴装 |
| 封装/外壳： | TO-263-4，D²Pak（3 引线+接片），TO-263AA |
| 供应商设备封装： | TO-263 |
| 包装： | 管件 |
| 其它名称： | *IRU1030CM IRU1030-CM IRU1030-CM-ND |
IRU1030
u SA = = = 17.8 8 C/W
Assuming the following specifications:
V IN = 3.3V
V OUT = 1.5V
I OUT(MAX) = 2.7A
T A = 35 8 C
The steps for selecting a proper heat sink to keep the
junction temperature below 135 ° C is given as:
1) Calculate the maximum power dissipation using:
P D = I OUT 3 (V IN - V OUT )
P D = 2.7 3 (3.3 - 1.5) = 4.86W
2) Select a package from the regulator data sheet and
record its junction to case (or tab) thermal resistance.
Selecting TO-220 package gives us:
u JC = 2.7 8 C/W
3) Assuming that the heat sink is black anodized, cal-
culate the maximum heat sink temperature allowed:
Assume, u cs=0.05 ° C/W (heat-sink-to-case thermal
resistance for black anodized)
T S = T J - P D 3 ( u JC + u CS )
T S = 135 - 4.86 3 (2.7 + 0.05) = 121.7 8 C
4) With the maximum heat sink temperature calculated
in the previous step, the heat-sink-to-air thermal re-
sistance ( u SA ) is calculated by first calculating the
temperature rise above the ambient as follows:
D T = T S - T A = 121.7 - 35 = 86.7 8 C
? T=Temperature Rise Above Ambient
D T 86.7
P D 4.86
5) Next, a heat sink with lower u SA than the one calcu-
lated in step 4 must be selected. One way to do this
is to simply look at the graphs of the “Heat Sink Temp
Rise Above the Ambient” vs. the “Power Dissipation”
and select a heat sink that results in lower tempera-
ture rise than the one calculated in the previous step.
The following heat sinks from AAVID and Thermalloy
meet this criteria.
Air Flow (LFM)
0 100 200 300
Thermalloy 6109PB 6110PB 7141 7178
AAVID 575002 507302 576802B 577102
Note: For further information regarding the above com-
panies and their latest product offerings and application
support contact your local representative or the num-
bers listed below:
AAVID................PH# (603) 528 3400
Thermalloy..........PH# (214) 243-4321
Designing for Microprocessor Applications
As it was mentioned before the IRU1030 is designed
specifically to provide power for the new generation of
the low voltage processors requiring voltages in the range
of 2.5V to 3.6V generated by stepping down the 5V
supply. These processors demand a fast regulator that
supports their large load current changes. The worst case
current step seen by the regulator is anywhere in the
range of 1 to 7A with the slew rate of 300 to 500ns which
could happen when the processor transitions from “Stop
Clock” mode to the “Full Active” mode. The load current
step at the processor is actually much faster, in the or-
der of 15 to 20ns, however the decoupling capacitors
placed in the cavity of the processor socket handle this
transition until the regulator responds to the load current
levels. Because of this requirement the selection of high
frequency low ESR and low ESL output capacitors is
imperative in the design of these regulator circuits.
Figure 5 shows the effects of a fast transient on the
output voltage of the regulator. As shown in this figure,
the ESR of the output capacitor produces an instanta-
neous drop equal to the ( ? V ESR =ESR 3 ? I) and the ESL
effect will be equal to the rate of change of the output
current times the inductance of the capacitor. ( ? V ESL
=L 3 ? I/ ? t). The output capacitance effect is a droop in
the output voltage proportional to the time it takes for the
regulator to respond to the change in the current,
( ? Vc= ? t 3 ? I/C) where ? t is the response time of the
regulator.
Rev. 1.3
08/20/02
www.irf.com
5
相关PDF资料 |
PDF描述 |
|---|---|
| VI-BVV-CY-F1 | CONVERTER MOD DC/DC 5.8V 50W |
| TCJY476M016R0070 | CAP TANT 47UF 16V 20% 2917 |
| TPSC106M020R0700 | CAP TANT 10UF 20V 20% 2312 |
| IRU1030CD | IC REG LDO ADJ 3A D-PAK |
| EBC17DCMT | CONN EDGECARD 34POS .100 WW |
相关代理商/技术参数 |
参数描述 |
|---|---|
| IRU1030CMTR | 功能描述:IC REG LDO ADJ 3A TO-263-3 RoHS:否 类别:集成电路 (IC) >> PMIC - 稳压器 - 线性 系列:- 标准包装:1 系列:- 稳压器拓扑结构:正，固定式 输出电压:4V 输入电压:最高 16V 电压 - 压降（标准）:0.28V @ 150mA 稳压器数量:1 电流 - 输出:150mA 电流 - 限制（最小）:- 工作温度:-40°C ~ 125°C 安装类型:表面贴装 封装/外壳:5-VFBGA 供应商设备封装:5-uSMD 包装:Digi-Reel® 其它名称:LP2985AIBP-4.0DKR |
| IRU1030CT | 功能描述:IC REG LDO ADJ 3A TO-220 RoHS:否 类别:集成电路 (IC) >> PMIC - 稳压器 - 线性 系列:- 标准包装:1 系列:- 稳压器拓扑结构:正，固定式 输出电压:4V 输入电压:最高 16V 电压 - 压降（标准）:0.28V @ 150mA 稳压器数量:1 电流 - 输出:150mA 电流 - 限制（最小）:- 工作温度:-40°C ~ 125°C 安装类型:表面贴装 封装/外壳:5-VFBGA 供应商设备封装:5-uSMD 包装:Digi-Reel® 其它名称:LP2985AIBP-4.0DKR |
| IRU1050 | 制造商:IRF 制造商全称:International Rectifier 功能描述:5A LOW DROPOUT POSITIVE ADJUSTABLE REGULATOR |
| IRU1050-33 | 制造商:IRF 制造商全称:International Rectifier 功能描述:5A LOW DROPOUT POSITIVE FIXED 3.3V REGULATOR |
| IRU1050-33CD | 功能描述:IC REG LDO 3.3V 5A D-PAK RoHS:否 类别:集成电路 (IC) >> PMIC - 稳压器 - 线性 系列:- 标准包装:1 系列:- 稳压器拓扑结构:正，固定式 输出电压:4V 输入电压:最高 16V 电压 - 压降（标准）:0.28V @ 150mA 稳压器数量:1 电流 - 输出:150mA 电流 - 限制（最小）:- 工作温度:-40°C ~ 125°C 安装类型:表面贴装 封装/外壳:5-VFBGA 供应商设备封装:5-uSMD 包装:Digi-Reel® 其它名称:LP2985AIBP-4.0DKR |
发布紧急采购，3分钟左右您将得到回复。