参数资料
| 型号： | IS82C54-10Z |
| 厂商： | Intersil |
| 文件页数： | 4/22页 |
| 文件大小： | 0K |
| 描述： | IC OSC PROG TIMER 10MHZ 28PLCC |
| 标准包装： | 37 |
| 类型： | 可编程计时器 |
| 频率： | 10MHz |
| 电源电压： | 4.5 V ~ 5.5 V |
| 电流 - 电源： | 10mA |
| 工作温度： | -40°C ~ 85°C |
| 封装/外壳： | 28-LCC（J 形引线） |
| 包装： | 管件 |
| 供应商设备封装： | 28-PLCC（11.51x11.51） |
| 安装类型： | 表面贴装 |
12
82C54
If an initial count is written while GATE = 0, it will still be
loaded on the next CLK pulse. When GATE goes high, OUT
will go high N CLK pulses later; no CLK pulse is needed to
load the counter as this has already been done.
NOTES: The following conventions apply to all mode timing diagrams.
1. Counters are programmed for binary (not BCD) counting and for
reading/writing least significant byte (LSB) only.
2. The counter is always selected (CS always low).
3. CW stands for “Control Word”; CW = 10 means a control word of
10, Hex is written to the counter.
4. LSB stands for Least significant “byte” of count.
5. Numbers below diagrams are count values. The lower number is
the least significant byte. The upper number is the most
significant byte. Since the counter is programmed to read/write
LSB only, the most significant byte cannot be read.
6. N stands for an undefined count.
7. Vertical lines show transitions between count values.
MODE 1: HARDWARE RETRIGGERABLE ONE-SHOT
OUT will be initially high. OUT will go low on the CLK pulse
following a trigger to begin the one-shot pulse, and will remain
low until the Counter reaches zero. OUT will then go high and
remain high until the CLK pulse after the next trigger.
After writing the Control Word and initial count, the Counter is
armed. A trigger results in loading the Counter and setting
OUT low on the next CLK pulse, thus starting the one-shot
pulse N CLK cycles in duration. The one-shot is retriggerable,
hence OUT will remain low for N CLK pulses after any trigger.
The one-shot pulse can be repeated without rewriting the
same count into the counter. GATE has no effect on OUT.
If a new count is written to the Counter during a one-shot
pulse, the current one-shot is not affected unless the
Counter is retriggerable. In that case, the Counter is loaded
with the new count and the one-shot pulse continues until
the new count expires.
CW = 10
LSB = 4
WR
CLK
GATE
OUT
WR
CLK
GATE
OUT
WR
CLK
GATE
OUT
CW = 10
LSB = 3
CW = 10
LSB = 3
LSB = 2
NNN
N
0
4
0
3
0
2
0
1
0
FF
FE
NNNN
0
3
0
2
0
2
0
2
0
1
0
FF
NNNN
0
3
0
2
0
1
0
2
0
1
0
FF
FIGURE 9. MODE 0
WR
CLK
GATE
OUT
WR
CLK
GATE
OUT
WR
CLK
GATE
OUT
NN
0
3
0
2
0
1
0
FF
0
3
0
2
N
CW = 12
LSB = 3
CW = 12
LSB = 3
CW = 12
LSB = 2
LSB = 4
N
NNN
0
2
0
1
0
FF
FE
0
4
0
3
N
NNNN
0
3
0
2
0
1
0
3
0
2
0
1
0
N
FIGURE 10. MODE 1
相关PDF资料 |
PDF描述 |
|---|---|
| V375A8M300BG | CONVERTER MOD DC/DC 8V 300W |
| LTC6905CS5-100#TRMPBF | IC OSC SILICON 100MHZ TSOT23-5 |
| ICM7555ISA+ | IC OSC MONO TIMING 500KHZ 8-SOIC |
| MC14536BDWR2G | IC OSC PROG TIMER 2MHZ 16SOIC |
| VE-B6F-IU | CONVERTER MOD DC/DC 72V 200W |
相关代理商/技术参数 |
参数描述 |
|---|---|
| IS82C54-10Z96 | 功能描述:计时器和支持产品 W/ANNEAL PERIPH PRG- CNTR 5V 10MHZ RoHS:否 制造商:Micrel 类型:Standard 封装 / 箱体:SOT-23 内部定时器数量:1 电源电压-最大:18 V 电源电压-最小:2.7 V 最大功率耗散: 最大工作温度:+ 85 C 最小工作温度:- 40 C 封装:Reel |
| IS82C54-12 | 制造商:Rochester Electronics LLC 功能描述:- Bulk |
| IS82C5496 | 功能描述:计时器和支持产品 PERIPH PRG-CNTR 5V 8MHZ 28PLCC INDEL RoHS:否 制造商:Micrel 类型:Standard 封装 / 箱体:SOT-23 内部定时器数量:1 电源电压-最大:18 V 电源电压-最小:2.7 V 最大功率耗散: 最大工作温度:+ 85 C 最小工作温度:- 40 C 封装:Reel |
| IS82C5496S2485 | 制造商:Rochester Electronics LLC 功能描述:- Bulk |
| IS82C54R2490 | 制造商:Rochester Electronics LLC 功能描述:- Bulk |
发布紧急采购，3分钟左右您将得到回复。