- 您现在的位置：买卖IC网 > PDF目录384518 > ISD2564X (WINBOND ELECTRONICS CORP) SINGLE-CHIP, MULTIPLE-MESSAGES, VOICE RECORD/PLAYBACK DEVICE 32-, 40-, 48-, AND 64-SECOND DURATION PDF资料下载
参数资料
| 型号： | ISD2564X |
| 厂商： | WINBOND ELECTRONICS CORP |
| 元件分类： | 音频合成 |
| 英文描述： | SINGLE-CHIP, MULTIPLE-MESSAGES, VOICE RECORD/PLAYBACK DEVICE 32-, 40-, 48-, AND 64-SECOND DURATION |
| 中文描述： | 64 SEC, SPEECH SYNTHESIZER WITH RCDG, UUC28 |
| 封装： | DIE-28 |
| 文件页数： | 14/42页 |
| 文件大小： | 1356K |
| 代理商： | ISD2564X |
第1页第2页第3页第4页第5页第6页第7页第8页第9页第10页第11页第12页第13页当前第14页第15页第16页第17页第18页第19页第20页第21页第22页第23页第24页第25页第26页第27页第28页第29页第30页第31页第32页第33页第34页第35页第36页第37页第38页第39页第40页第41页第42页
ISD2532/40/48/64
2. The P/
R
pin is taken LOW.
3. The
CE
pin is pulsed LOW. Recording starts,
EOM
goes HIGH to indicate an
operation in progress.
4. When the
CE
pin is pulsed LOW. Recording pauses,
EOM
goes back LOW. The
internal address pointers are not cleared, but the
EOM
marker is stored in memory to
indicate as the message end. The P/
R
pin may be taken HIGH at this time. Any
subsequent
CE
would start a playback at address 0.
5. The
CE
pin is pulsed LOW. Recording starts at the next address after the previous set
EOM
marker.
EOM
goes back HIGH.
[3]
6. When the recording sequences are finished, the final
CE
pulse LOW will end the last
record cycle, leaving a set
EOM
marker at the message end. Recording may also be
terminated by a HIGH level on PD, which will leave a set
EOM
marker.
Playback in Push-Button Mode
1. The PD pin should be LOW.
2. The P/
R
pin is taken HIGH.
3. The
CE
pin is pulsed LOW. Playback starts,
EOM
goes HIGH to indicate an operation
in progress.
4. If the
CE
pin is pulsed LOW or an
EOM
marker is encountered during an operation,
the part will pause. The internal address pointers are not cleared, and
EOM
goes back
LOW. The P/
R
pin may be changed at this time. A subsequent record operation would
not reset the address pointers and the recording would begin where playback ended.
5.
CE
is again pulsed LOW. Playback starts where it left off, with
EOM
going HIGH to
indicate an operation in progress.
6. Playback continues as in steps 4 and 5 until PD is pulsed HIGH or overflow occurs.
7. If in overflow, pulling
CE
LOW will reset the address pointer and start playback from the
beginning. After a PD pulse, the part is reset to address 0.
Note: Push-Button Mode can be used in conjunction with modes M0, M1, and M3.
[3]
If the M1 Operational Mode pin is also HIGH, the just previously written
EOM
bit is erased, and recording starts at that
address.
- 14 -
相关PDF资料 |
PDF描述 |
|---|---|
| ISD2540 | Single-Chip Voice Record/Playback Device（Single-chip Durations of 40 seconds)(单片的录音/录音重放器(一片信息存储持续时间40秒）) |
| ISD2532 | Single-Chip Voice Record/Playback Device（Single-chip Durations of 32 seconds)(单片的录音/录音重放器(一片信息存储持续时间32秒）) |
| ISD2564 | Single-Chip Voice Record/Playback Device（Single-chip Durations of 64 seconds)(单片的录音/录音重放器(一片信息存储持续时间64秒）) |
| ISD2548 | Single-Chip Voice Record/Playback Device（Single-chip Durations of 48 seconds)(单片的录音/录音重放器(一片信息存储持续时间48秒）) |
| ISD33075 | Single-Chip Voice Record/Playback Devices 60-, 75-, 90-, and 120-Second Durations(单片声音录音/回放芯片(单片信息存储持续时间75秒钟)) |
相关代理商/技术参数 |
参数描述 |
|---|---|
| ISD2575 | 制造商:WINBOND 制造商全称:Winbond 功能描述:ISD2560 |
| ISD2575E | 功能描述:IC VOICE REC/PLAY 75-SEC 28-TSOP RoHS:否 类别:集成电路 (IC) >> 接口 - 语音录制和重放 系列:ISD2500 标准包装:14 系列:- 接口:串行 滤波器通频带:1.7kHz 持续时间:8 ~ 32 秒 安装类型:通孔 封装/外壳:28-DIP（0.300"，7.62mm） 供应商设备封装:28-PDIP 其它名称:90-21300+000 |
| ISD2575EI | 制造商:未知厂家 制造商全称:未知厂家 功能描述:Single-Chip Voice Record/Playback Devices 32-, 40-, 48-, 64-,60-,75,90-, and 120-Second Durations |
| ISD2575ER | 功能描述:IC VOICE REC/PLAY 75-SEC 28-TSOP RoHS:否 类别:集成电路 (IC) >> 接口 - 语音录制和重放 系列:ISD2500 标准包装:14 系列:- 接口:串行 滤波器通频带:1.7kHz 持续时间:8 ~ 32 秒 安装类型:通孔 封装/外壳:28-DIP（0.300"，7.62mm） 供应商设备封装:28-PDIP 其它名称:90-21300+000 |
| ISD2575G | 制造商:未知厂家 制造商全称:未知厂家 功能描述: |
发布紧急采购，3分钟左右您将得到回复。