参数资料
| 型号： | ISL12023IVZ |
| 厂商： | Intersil |
| 文件页数： | 18/29页 |
| 文件大小： | 0K |
| 描述： | IC RTC/CLDR TEMP SNSR 14-TSSOP |
| 产品培训模块： | Solutions for Industrial Control Applications |
| 标准包装： | 960 |
| 类型： | 时钟/日历 |
| 特点： | 警报器，夏令时，闰年，SRAM |
| 存储容量： | 128B |
| 时间格式： | HH:MM:SS（12/24 小时） |
| 数据格式： | YY-MM-DD-dd |
| 接口： | I²C，2 线串口 |
| 电源电压： | 2.7 V ~ 5.5 V |
| 电压 - 电源，电池： | 1.8 V ~ 5.5 V |
| 工作温度： | -40°C ~ 85°C |
| 安装类型： | 表面贴装 |
| 封装/外壳： | 14-TSSOP（0.173"，4.40mm 宽） |
| 供应商设备封装： | 14-TSSOP |
| 包装： | 管件 |
第1页第2页第3页第4页第5页第6页第7页第8页第9页第10页第11页第12页第13页第14页第15页第16页第17页当前第18页第19页第20页第21页第22页第23页第24页第25页第26页第27页第28页第29页
ISL12023
25
FN6682.3
December 6, 2011
The diode, DBAT will add a small drop to the battery voltage but
will protect the circuit should battery voltage drop below 1.8V.
The jumper is added as a safeguard should the battery ever need
to be disconnect from the circuit.
The VDD negative slew rate should be limited to below the data
sheet spec (10V/ms) otherwise battery switchover can be
delayed, resulting in SRAM contents corruption and oscillator
operation interruption.
Oscillator Crystal Requirements
The ISL12023 uses a standard 32.768kHz crystal. Either through
hole or surface mount crystals can be used. Table 28 lists some
recommended surface mount crystals and the parameters of each.
This list is not exhaustive and other surface mount devices can be
used with the ISL12023 if their specifications are very similar to the
devices listed. The crystal should have a required parallel load
capacitance of 12.5pF and an equivalent series resistance of less
than 50k. The crystal’s temperature range specification should
match the application. Many crystals are rated for -10°C to +60°C
(especially through hole and tuning fork types), so an appropriate
crystal should be selected if extended temperature range is
required.
Layout Considerations
The crystal input at X1 has a very high impedance, and oscillator
circuits operating at low frequencies such as 32.768kHz, are known
to pick up noise very easily if layout precautions are not followed.
Most instances of erratic clocking or large accuracy errors can be
traced to the susceptibility of the oscillator circuit to interference
from adjacent high speed clock or data lines. Careful layout of the
RTC circuit will avoid noise pickup and insure accurate clocking.
Figure 20 shows a suggested layout for the ISL12023 device
using a surface mount crystal. Two main precautions should be
followed:
1. Do not run the serial bus lines or any high speed logic lines in
the vicinity of the crystal. These logic level lines can induce
noise in the oscillator circuit to cause misclocking.
2. Add a ground trace around the crystal with one end terminated
at the chip ground. This will provide termination for emitted
noise in the vicinity of the RTC device.
In addition, it is a good idea to avoid a ground plane under the X1
and X2 pins and the crystal, as this will affect the load
capacitance, and therefore, the oscillator accuracy of the circuit. If
the FOUT pin is used as a clock, it should be routed away from the
RTC device as well. The traces for the VBAT and VDD pins can be
treated as a ground, and should be routed around the crystal.
Crystal Oscillator Frequency Compensation
CRYSTAL CHARACTERISTICS
The ISL12023 device contains a complete system for adjusting
the frequency of the crystal oscillator to compensate for
temperature variation. A typical 32.768kHz crystal used with RTC
devices has a temperature versus frequency curve, as shown in
Figure 21.
This curve equation follows Equation 6:
Where
α is the temperature constant, with a typical value of
0.034 ppm/°C.
T0 is the turnover temperature of the crystal, which is the apex of
the parabolic curve. If the two factors
α and T0 are known, it is
possible to correct for crystal temperature error to very high
accuracy.
The crystal will have an initial accuracy error at room
temperature, typically specified at ±20°C. The other important
TABLE 28. SUGGESTED SURFACE MOUNT CRYSTALS
MANUFACTURER
PART NUMBER
Citizen
CM200S
Epson
MC-405, MC-406
Raltron
RSM-200S
SaRonix
32S12
Ecliptek
ECPSM29T-32.768K
ECS
ECX-306
Fox
FSM-327
FIGURE 19. SUGGESTED BATTERY-BACKUP CIRCUIT
DBAT
CBAT
CIN
BAT43W
0.1F
VDD = 2.7V
TO 5.5V
VBAT = 1.8V
TO 3.2V
JBAT
ISL12023
VDD
GND
VBAT
+
FIGURE 20. SUGGESTED LAYOUT FOR ISL12023 AND CRYSTAL
TEMPERATURE (°C)
-160
-140
-120
-100
-80
-60
-40
-20
0
-40 -30 -20 -10 0 102030 40 50607080
PP
M
FIGURE 21. RTC CRYSTAL TEMPERATURE DRIFT
Δf
α
T
(
T0)
2
–
=
(EQ. 6)
相关PDF资料 |
PDF描述 |
|---|---|
| ISL12024IRTCZ | IC RTC/CALENDER 64BIT 8-TDFN |
| ISL12024IVZ | IC RTC/CALENDAR EEPROM 8-TSSOP |
| ISL12025IVZ | IC RTC/CALENDAR EEPROM 8-TSSOP |
| ISL12026IBZ-T7A | IC RTC/CALENDAR EEPROM 8SOIC |
| ISL12027IV27AZ | IC RTC/CALENDAR EEPROM 8-TSSOP |
相关代理商/技术参数 |
参数描述 |
|---|---|
| ISL12023IVZ-T | 功能描述:实时时钟 REAL TIME CLK/CLNDR W/TEMP COM 14 L RoHS:否 制造商:Microchip Technology 功能:Clock, Calendar. Alarm RTC 总线接口:I2C 日期格式:DW:DM:M:Y 时间格式:HH:MM:SS RTC 存储容量:64 B 电源电压-最大:5.5 V 电源电压-最小:1.8 V 最大工作温度:+ 85 C 最小工作温度: 安装风格:Through Hole 封装 / 箱体:PDIP-8 封装:Tube |
| ISL12024 | 制造商:INTERSIL 制造商全称:Intersil Corporation 功能描述:Real-Time Clock/Calendar with Embedded Unique ID |
| ISL12024IBZ | 功能描述:实时时钟 REAL TIME CLK/CLNDR W/EEPROM IN 8LD RoHS:否 制造商:Microchip Technology 功能:Clock, Calendar. Alarm RTC 总线接口:I2C 日期格式:DW:DM:M:Y 时间格式:HH:MM:SS RTC 存储容量:64 B 电源电压-最大:5.5 V 电源电压-最小:1.8 V 最大工作温度:+ 85 C 最小工作温度: 安装风格:Through Hole 封装 / 箱体:PDIP-8 封装:Tube |
| ISL12024IBZ-T | 功能描述:实时时钟 REAL TIME CLK/CLNDR W/EEPROM IN 8LD RoHS:否 制造商:Microchip Technology 功能:Clock, Calendar. Alarm RTC 总线接口:I2C 日期格式:DW:DM:M:Y 时间格式:HH:MM:SS RTC 存储容量:64 B 电源电压-最大:5.5 V 电源电压-最小:1.8 V 最大工作温度:+ 85 C 最小工作温度: 安装风格:Through Hole 封装 / 箱体:PDIP-8 封装:Tube |
| ISL12024IRTCZ | 功能描述:实时时钟 RTC OUTPUT PROGRAM TO 32KHZ W/EEPROM 8 RoHS:否 制造商:Microchip Technology 功能:Clock, Calendar. Alarm RTC 总线接口:I2C 日期格式:DW:DM:M:Y 时间格式:HH:MM:SS RTC 存储容量:64 B 电源电压-最大:5.5 V 电源电压-最小:1.8 V 最大工作温度:+ 85 C 最小工作温度: 安装风格:Through Hole 封装 / 箱体:PDIP-8 封装:Tube |
发布紧急采购，3分钟左右您将得到回复。