- 您现在的位置：买卖IC网 > PDF目录383128 > ISL1208IB8Z-TK (INTERSIL CORP) I2C Real Time Clock/Calendar PDF资料下载
参数资料
| 型号： | ISL1208IB8Z-TK |
| 厂商： | INTERSIL CORP |
| 元件分类： | XO, clock |
| 英文描述： | I2C Real Time Clock/Calendar |
| 中文描述： | REAL TIME CLOCK, PDSO8 |
| 封装： | ROHS COMPLIANT, SOIC-8 |
| 文件页数： | 13/21页 |
| 文件大小： | 393K |
| 代理商： | ISL1208IB8Z-TK |
13
FN8085.3
July 29, 2005
and X2 pins to ground (see Figure 11). The value of C
X1
and
C
X2
is given by the following formula:
The effective series load capacitance is the combination of
C
X1
and C
X2
:
For example, C
LOAD
(ATR=00000) = 12.5pF,
C
LOAD
(ATR=100000) = 4.5pF, and C
LOAD
(ATR=011111) =
20.25pF. The entire range for the series combination of load
capacitance goes from 4.5pF to 20.25pF in 0.25pF steps.
Note that these are typical values.
BATTERY MODE ATR SELECTION (BMATR <1:0>)
Since the accuracy of the crystal oscillator is dependent on
the V
DD
/V
BAT
operation, the ISL1208 provides the capability
to adjust the capacitance between V
DD
and V
BAT
when the
device switches between power sources.
DIGITAL TRIMMING REGISTER (DTR <2:0>)
The digital trimming bits DTR0, DTR1, and DTR2 adjust the
average number of counts per second and average the ppm
error to achieve better accuracy.
DTR2 is a sign bit. DTR2 = “0” means frequency
compensation is >0. DTR2 = “1” means frequency
compensation is <0.
DTR1 and DTR0 are both scale bits. DTR1 gives 40ppm
adjustment and DTR0 gives 20ppm adjustment.
A range from -60ppm to +60ppm can be represented by
using these three bits (see Table 5).
Alarm Registers
Addresses [0Ch to 11h]
The alarm register bytes are set up identical to the RTC
register bytes, except that the MSB of each byte functions as
an enable bit (enable = “1”). These enable bits specify which
alarm registers (seconds, minutes, etc) are used to make the
comparison. Note that there is no alarm byte for year.
The alarm function works as a comparison between the
alarm registers and the RTC registers. As the RTC
advances, the alarm will be triggered once a match occurs
between the alarm registers and the RTC registers. Any one
alarm register, multiple registers, or all registers can be
enabled for a match.
There are two alarm operation modes: Single Event and
periodic Interrupt Mode:
Single Event Mode
is enabled by setting the ALME bit to
“1”, the IM bit to “0”, and disabling the frequency output.
This mode permits a one-time match between the alarm
registers and the RTC registers. Once this match occurs,
the ALM bit is set to “1” and the IRQ output will be pulled
low and will remain low until the ALM bit is reset. This can
be done manually or by using the auto-reset feature.
Interrupt Mode
is enabled by setting the ALME bit to “1”,
the IM bit to “1”, and disabling the frequency output. The
IRQ output will now be pulsed each time an alarm occurs.
This means that once the interrupt mode alarm is set, it
will continue to alarm for each occurring match of the
alarm and present time. This mode is convenient for
hourly or daily hardware interrupts in microcontroller
applications such as security cameras or utility meter
reading.
To clear an alarm, the ALM bit in the status register must be
set to “0” with a write. Note that if the ARST bit is set to 1
(address 07h, bit 7), the ALM bit will automatically be cleared
when the status register is read.
BMATR1
BMATR0
DELTA
CAPACITANCE
(C
BAT
TO C
VDD
)
0
0
0pF
0
1
-0.5pF (
≈
+2ppm)
1
0
+0.5pF (
≈
-2ppm)
1
1
+1pF (
≈
-4ppm)
CX
16 b5
8 b4
4 b3
2 b2
1 b1
0.5 b0
9
+
+
+
+
+
+
(
)
pF
=
CLOAD
X1
----------
X2
----------
+
----------------------------------
=
CLOAD
-----------------------------------------------------------------------------------------------------------------------------
2
9
+
pF
=
TABLE 5. DIGITAL TRIMMING REGISTERS
DTR REGISTER
ESTIMATED
FREQUENCY
PPM
DTR2
DTR1
DTR0
0
0
0
0 (default)
0
0
1
+20
0
1
0
+40
0
1
1
+60
1
0
0
0
1
0
1
-20
1
1
0
-40
1
1
1
-60
ISL1208
相关PDF资料 |
PDF描述 |
|---|---|
| ISL1208IU8 | I2C Real Time Clock/Calendar |
| ISL1208IU8Z | I2C Real Time Clock/Calendar |
| ISL1208IB8 | I2C Real Time Clock/Calendar |
| ISL1208IB8-TK | I2C Real Time Clock/Calendar |
| ISL1208 | I2C Real Time Clock/Calendar(I2C实时时钟/日历) |
相关代理商/技术参数 |
参数描述 |
|---|---|
| ISL1208IB8Z-TKR5291 | 功能描述:实时时钟 I2CAL TIME CLK/CLNDR BATRY MODE TESTS RoHS:否 制造商:Microchip Technology 功能:Clock, Calendar. Alarm RTC 总线接口:I2C 日期格式:DW:DM:M:Y 时间格式:HH:MM:SS RTC 存储容量:64 B 电源电压-最大:5.5 V 电源电压-最小:1.8 V 最大工作温度:+ 85 C 最小工作温度: 安装风格:Through Hole 封装 / 箱体:PDIP-8 封装:Tube |
| ISL1208IRT8Z | 功能描述:实时时钟 I2CAL TIME CLK/CLNDR 8LD 3X3 RoHS:否 制造商:Microchip Technology 功能:Clock, Calendar. Alarm RTC 总线接口:I2C 日期格式:DW:DM:M:Y 时间格式:HH:MM:SS RTC 存储容量:64 B 电源电压-最大:5.5 V 电源电压-最小:1.8 V 最大工作温度:+ 85 C 最小工作温度: 安装风格:Through Hole 封装 / 箱体:PDIP-8 封装:Tube |
| ISL1208IRT8Z-TK | 功能描述:实时时钟 I2CAL TIME CLK/CLNDR 8LD 3X3 RoHS:否 制造商:Microchip Technology 功能:Clock, Calendar. Alarm RTC 总线接口:I2C 日期格式:DW:DM:M:Y 时间格式:HH:MM:SS RTC 存储容量:64 B 电源电压-最大:5.5 V 电源电压-最小:1.8 V 最大工作温度:+ 85 C 最小工作温度: 安装风格:Through Hole 封装 / 箱体:PDIP-8 封装:Tube |
| ISL1208IU8 | 功能描述:IC RTC LP BATT BACKED SRAM 8MSOP RoHS:否 类别:集成电路 (IC) >> 时钟/计时 - 实时时钟 系列:- 产品培训模块:Obsolescence Mitigation Program 标准包装:1 系列:- 类型:时钟/日历 特点:警报器，闰年，SRAM 存储容量:- 时间格式:HH:MM:SS（12/24 小时） 数据格式:YY-MM-DD-dd 接口:SPI 电源电压:2 V ~ 5.5 V 电压 - 电源，电池:- 工作温度:-40°C ~ 85°C 安装类型:表面贴装 封装/外壳:8-WDFN 裸露焊盘 供应商设备封装:8-TDFN EP 包装:管件 |
| ISL1208IU8-TK | 功能描述:IC RTC/CALENDAR I2C 8-MSOP RoHS:否 类别:集成电路 (IC) >> 时钟/计时 - 实时时钟 系列:- 产品培训模块:Obsolescence Mitigation Program 标准包装:1 系列:- 类型:时钟/日历 特点:警报器，闰年，SRAM 存储容量:- 时间格式:HH:MM:SS（12/24 小时） 数据格式:YY-MM-DD-dd 接口:SPI 电源电压:2 V ~ 5.5 V 电压 - 电源，电池:- 工作温度:-40°C ~ 85°C 安装类型:表面贴装 封装/外壳:8-WDFN 裸露焊盘 供应商设备封装:8-TDFN EP 包装:管件 |
发布紧急采购，3分钟左右您将得到回复。