- 您现在的位置：买卖IC网 > PDF目录381957 > ISL21032 (Intersil Corporation) Precision 0.600V Low Voltage FGA References(精密0.600V低压FGA基准) PDF资料下载
参数资料
| 型号： | ISL21032 |
| 厂商： | Intersil Corporation |
| 英文描述： | Precision 0.600V Low Voltage FGA References(精密0.600V低压FGA基准) |
| 中文描述： | 精密0.600V低电压FGA中参考（精密0.600V低压FGA中基准） |
| 文件页数： | 5/6页 |
| 文件大小： | 219K |
| 代理商： | ISL21032 |
5
FGA Technology
The ISL21032 series of voltage references use the floating
gate technology to create references with very low drift and
supply current. Essentially the charge stored on a floating
gate cell is set precisely in manufacturing. The reference
voltage output itself is a buffered version of the floating gate
voltage. The resulting reference device has excellent
characteristics which are unique in the industry: very low
temperature drift, high initial accuracy, and almost zero
supply current. Also, the reference voltage itself is not limited
by voltage bandgaps or zener settings, so a wide range of
reference voltages can be programmed (standard voltage
settings are provided, but customer-specific voltages are
available).
The process used for these reference devices is a floating
gate CMOS process, and the amplifier circuitry uses CMOS
transistors for amplifier and output transistor circuitry. While
providing excellent accuracy, there are limitations in output
noise level and load regulation due to the MOS device
characteristics. These limitations are addressed with circuit
techniques discussed in other sections.
Board Mounting Considerations
For applications requiring the highest accuracy, board
mounting location should be reviewed. Placing the device in
areas subject to slight twisting can cause degradation of the
accuracy of the reference voltage due to die stresses. It is
normally best to place the device near the edge of a board,
or the shortest side, as the axis of bending is most limited at
that location. Obviously mounting the device on flexprint or
extremely thin PC material will likewise cause loss of
reference accuracy.
Noise Performance and Reduction
The output noise voltage in a 0.1Hz to 10Hz bandwidth is
typically 30μV
P-P
. The noise measurement is made with a
bandpass filter made of a 1 pole high-pass filter with a corner
frequency at 0.1Hz and a 2-pole low-pass filter with a corner
frequency at 12.6Hz to create a filter with a 9.9Hz
bandwidth. Wideband noise is reduced by adding capacitor
to the output, but the value should be limited to 1nF or less
to insure stability.
Temperature Drift
The limits stated for output accuracy over temperature are
governed by the method of measurement. For the -40°C to
130°C temperature range, measurements are made at 25°C
and the two extremes. This measurement method combined
with the fact that FGA references have a fairly linear
temperature drift characteristic insures that the limits stated
will not be exceeded over the temperature range.
FIGURE 13. Z
OUT
vs f vs C
L
FIGURE 14. V
OUT
NOISE
Typical Performance Curves, ISL21032 Low Voltage Output Reference
V
IN
= 3.0V, I
OUT
= 0mA, T
A
= 25°C Unless Otherwise Specified
(Continued)
0
20
40
60
80
100
120
1
10
100
1K
10K
100K
1M
FREQUENCY (Hz)
Z
O
)
NO LOAD
100nF LOAD
1nF LOAD
10nF LOAD
10s/DIV
5
FIGURE 15. PRECISION LOW NOISE, LOW DRIFT, 0.6V, 50mA
REFERENCE
V
IN
= 5V
2N2905
0.6V/50mA
0.001μF
V
IN
V
OUT
GND
ISL21032
R = 200
ISL21032
相关PDF资料 |
PDF描述 |
|---|---|
| ISL28271 | Dual Micropower, Single Supply, Rail-to-Rail Input and Output (RRIO) Instrumentation Amplifier(双微功率,单电源,轨对轨输入/输出(RRIO)测量放大器) |
| ISL28272 | Dual Micropower, Single Supply, Rail-to-Rail Input and Output (RRIO) Instrumentation Amplifier(双微功率,单电源,轨对轨输入/输出(RRIO)测量放大器) |
| ISL28278 | Dual and Quad Micropower Single Supply Rail-to-Rail Input and Output (RRIO) Op-Amp(双/四通道，微功率，单电源，轨对轨输入/输出(RRIO)运放) |
| ISL28478 | Dual and Quad Micropower Single Supply Rail-to-Rail Input and Output (RRIO) Op-Amp(双/四通道，微功率，单电源，轨对轨输入/输出(RRIO)运放) |
| ISL28286 | Dual and Quad Micropower Single Supply Rail-to-Rail Input and Output (RRIO) Precision Op Amp(双/四通道，微功率，单电源，轨对轨输入/输出(RRIO)精密运放) |
相关代理商/技术参数 |
参数描述 |
|---|---|
| ISL21032BPH306Z | 制造商:INTERSIL 制造商全称:Intersil Corporation 功能描述:Precision 0.600V Low Voltage FGA⑩ References |
| ISL21032BPH306Z-TK | 功能描述:IC VREF SERIES PREC 0.6V SOT23-3 RoHS:是 类别:集成电路 (IC) >> PMIC - 电压基准 系列:FGA™ 标准包装:3,000 系列:- 基准类型:旁路，精度 输出电压:5V 容差:±0.5% 温度系数:100ppm/°C 输入电压:- 通道数:1 电流 - 阴极:80µA 电流 - 静态:- 电流 - 输出:15mA 工作温度:-40°C ~ 85°C 安装类型:表面贴装 封装/外壳:TO-236-3，SC-59，SOT-23-3 供应商设备封装:SOT-23-3 包装:带卷 (TR) 其它名称:LM4040CIM3-5.0MLTRLM4040CIM3-5.0MLTR-ND |
| ISL21032CPH306Z | 制造商:Rochester Electronics LLC 功能描述: 制造商:Intersil Corporation 功能描述: |
| ISL21032CPH306Z-TK | 功能描述:IC VREF SERIES PREC 0.6V SOT23-3 RoHS:是 类别:集成电路 (IC) >> PMIC - 电压基准 系列:FGA™ 标准包装:3,000 系列:- 基准类型:旁路，精度 输出电压:5V 容差:±0.5% 温度系数:100ppm/°C 输入电压:- 通道数:1 电流 - 阴极:80µA 电流 - 静态:- 电流 - 输出:15mA 工作温度:-40°C ~ 85°C 安装类型:表面贴装 封装/外壳:TO-236-3，SC-59，SOT-23-3 供应商设备封装:SOT-23-3 包装:带卷 (TR) 其它名称:LM4040CIM3-5.0MLTRLM4040CIM3-5.0MLTR-ND |
| ISL21032DPH306Z | 制造商:Rochester Electronics LLC 功能描述: 制造商:Intersil Corporation 功能描述: |
发布紧急采购，3分钟左右您将得到回复。