- 您现在的位置：买卖IC网 > PDF目录20667 > ISL22102IR20Z-EVAL (Intersil)EVAL BOARD FOR ISL22102IR20Z PDF资料下载
参数资料
| 型号： | ISL22102IR20Z-EVAL |
| 厂商： | Intersil |
| 文件页数： | 10/11页 |
| 文件大小： | 0K |
| 描述： | EVAL BOARD FOR ISL22102IR20Z |
| 标准包装： | 1 |
| 系列： | * |
8
FN6788.1
January 14, 2010
VTH
This terminal allows to set up the threshold level of audio
input to be detected. When audio input to either Left or Right
channel is below this threshold - the FLAG output is Low;
when audio input is above this threshold - the FLAG output
is High. The threshold level is maintained over an external
resistor RTH placed between VTH pin, which is a source of
±10A current, and VB pin. To calculate the actual threshold
we need to multiply 10A by a resistor value and divide the
result by 1000. For example, a 100k
Ω resistor is a subject of
1mV audio detection threshold, e.g. 10A*100k/1000 = 1mV.
Note, the VTH threshold multiplied by 1000 should not exceed
1/2 of AVCC. The maximum resistor value for detection
threshold can be found in Table 2.
Device Operation
There are four sections in the ISL22102: the input control,
counter and decode section, two resistor arrays with
buffered wiper outputs, reference voltage generator of VB
output, and audio detection block with programmable delay
FLAG output. The input control section operates just like an
up/down counter. The output of this counter is decoded to
turn on a single electronic switch, connecting a point on the
resistor array to the wiper output. Each resistor array is
comprised of 31 individual resistors connected in series and
its wiper output pass an attenuated audio input to the power
amplifier. Both resistor arrays have logarithmic taper with
-72dB dynamic range as shown in Table 2.
The ISL22102 is designed to interface directly to two
push-button switches for effectively moving the wipers up or
down. The UP and DN inputs increment or decrement 5-bit
counters respectively. The output of these counters are
decoded to select one of the thirty-two wiper positions along
the resistive array. The wiper increment input, UP, and the
wiper decrement input, DN, are both connected to an
internal pull-up so that they normally remain High. When
pulled Low by an external push button switch or a logic Low
level input, the wipers will be switched to the next adjacent
tap position.
Internal debounce circuitry prevents inadvertent switching of
the wipers position if UP or DN remain Low for less than
15ms, typical. Each of the buttons can be pushed either
once for a single increment/decrement or continuously for a
multiple increments/decrements. When making a continuous
push, after the first second, the device is going to auto
increment/decrement mode. If the button is held for longer
than 1s, the wiper position will be auto
incremented/decremented with a rate of 4Hz for 4s, and with
a rate of 8Hz after that. As soon as the button is released,
the ISL22102 will return to a low power standby condition.
Each wiper acts like its mechanical equivalent and does not
move beyond the last position. That is, the counter does not
wrap around when clocked to either extreme.
Table 3 contains information about attenuation level for each
tap position.
TABLE 2. RTH vs AVCC
AVCC (V)
MAX RTH (kΩ)
5.5
188
5.25
177
5.0
167
4.75
156
4.5
146
4.25
135
4.0
125
3.75
115
3.5
104
3.25
94
3.0
83
2.75
73
TABLE 3. WIPER TAP POSITION vs ATTENUATION
TAP POSITION
ATTENUATION
00
1-2dB
2-4dB
3-6dB
4-8dB
5
-10dB
6
-12dB
7
-14dB
8
-16dB
9
-18dB
10
-20dB
11
-22dB
12
-24dB
13
-26dB
14
-28dB
15
-30dB
16
-32dB
17
-34dB
18
-36dB
19
-38dB
20
-40dB
21
-42dB
22
-44dB
23
-46dB
24
-48dB
ISL22102
相关PDF资料 |
PDF描述 |
|---|---|
| VE-2NV-EW-B1 | CONVERTER MOD DC/DC 5.8V 100W |
| GBM10DCAI | CONN EDGECARD 20POS R/A .156 SLD |
| VI-J6K-CX-F1 | CONVERTER MOD DC/DC 40V 75W |
| EBM11DSEN | CONN EDGECARD 22POS .156 EYELET |
| TH3D685M050D0900 | CAP TANT 6.8UF 50V 20% 2917 |
相关代理商/技术参数 |
参数描述 |
|---|---|
| ISL22102IR20Z-TK | 功能描述:数字电位计 IC 32 TAP PUSH-BUTTON DL AUD LOG W/BUFR RoHS:否 制造商:Maxim Integrated 电阻:200 Ohms 温度系数:35 PPM / C 容差:25 % POT 数量:Dual 每 POT 分接头:256 弧刷存储器:Volatile 缓冲刷: 数字接口:Serial (3-Wire, SPI) 描述/功能:Dual Volatile Low Voltage Linear Taper Digital Potentiometer 工作电源电压:1.7 V to 5.5 V 电源电流:27 uA 最大工作温度:+ 125 C 安装风格:SMD/SMT 封装 / 箱体:TQFN-16 封装:Reel |
| ISL22102IV20Z | 功能描述:数字电位计 IC 32 TAP PUSH-BUTTON DL AUD LOG W/BUFR RoHS:否 制造商:Maxim Integrated 电阻:200 Ohms 温度系数:35 PPM / C 容差:25 % POT 数量:Dual 每 POT 分接头:256 弧刷存储器:Volatile 缓冲刷: 数字接口:Serial (3-Wire, SPI) 描述/功能:Dual Volatile Low Voltage Linear Taper Digital Potentiometer 工作电源电压:1.7 V to 5.5 V 电源电流:27 uA 最大工作温度:+ 125 C 安装风格:SMD/SMT 封装 / 箱体:TQFN-16 封装:Reel |
| ISL22102IV20Z-EVAL | 功能描述:数字电位计开发工具 ISL22102IV20Z-EVAL D EMO BRD RoHS:否 制造商:Arduino 产品:TinkerKit Rotary Potentiometers 工具用于评估:TinkerKit 电阻:4.7 kOhms 工作电源电压:0 V to 5 V |
| ISL22102IV20Z-TK | 功能描述:数字电位计 IC 32 TAP PUSH-BUTTON DL AUD LOG W/BUFR RoHS:否 制造商:Maxim Integrated 电阻:200 Ohms 温度系数:35 PPM / C 容差:25 % POT 数量:Dual 每 POT 分接头:256 弧刷存储器:Volatile 缓冲刷: 数字接口:Serial (3-Wire, SPI) 描述/功能:Dual Volatile Low Voltage Linear Taper Digital Potentiometer 工作电源电压:1.7 V to 5.5 V 电源电流:27 uA 最大工作温度:+ 125 C 安装风格:SMD/SMT 封装 / 箱体:TQFN-16 封装:Reel |
| ISL22313 | 制造商:INTERSIL 制造商全称:Intersil Corporation 功能描述:Single Digitally Controlled Potentiometer XDCP |
发布紧急采购，3分钟左右您将得到回复。