- 您现在的位置：买卖IC网 > PDF目录383128 > ISL22326 (Intersil Corporation) Low Noise, Low Power, I2C Bus, 128 Taps(低噪声,低功率，I2C总线, 128抽头电位器) PDF资料下载
参数资料
| 型号： | ISL22326 |
| 厂商： | Intersil Corporation |
| 英文描述： | Low Noise, Low Power, I2C Bus, 128 Taps(低噪声,低功率，I2C总线, 128抽头电位器) |
| 中文描述： | 低噪声，低功耗，I2C总线，128丝锥（低噪声，低功率和I2C总线，128抽头电位器） |
| 文件页数： | 11/13页 |
| 文件大小： | 488K |
| 代理商： | ISL22326 |
11
FN6176.0
July 17, 2006
An ACK, Acknowledge, is a software convention used to
indicate a successful data transfer. The transmitting device,
either master or slave, releases the SDA bus after
transmitting eight bits. During the ninth clock cycle, the
receiver pulls the SDA line LOW to acknowledge the
reception of the eight bits of data (See Figure 17).
The ISL22326 responds with an ACK after recognition of a
START condition followed by a valid Identification Byte, and
once again after successful receipt of an Address Byte. The
ISL22326 also responds with an ACK after receiving a Data
Byte of a write operation. The master must respond with an
ACK after receiving a Data Byte of a read operation.
A valid Identification Byte contains 1010 as the four MSBs,
and the following three bits matching the logic values
present at pins A2, A1, and A0. The LSB is the Read/Write
bit. Its value is “1” for a Read operation, and “0” for a Write
operation (See Table 3).
TABLE 3. IDENTIFICATION BYTE FORMAT
1
0
1
0
A2
A1
A0
R/W
(MSB)
(LSB)
Logic values at pins A2, A1, and A0 respectively
SDA
SCL
START
DATA
STABLE
DATA
CHANGE
STOP
DATA
STABLE
FIGURE 16. VALID DATA CHANGES, START AND STOP CONDITIONS
SDA OUTPUT FROM
TRANSMITTER
SDA OUTPUT FROM
RECEIVER
8
1
9
START
ACK
SCL FROM
MASTER
HIGH IMPEDANCE
HIGH IMPEDANCE
FIGURE 17. ACKNOWLEDGE RESPONSE FROM RECEIVER
S
T
A
R
T
S
T
O
P
IDENTIFICATION
BYTE
ADDRESS
BYTE
DATA
BYTE
A
C
K
SIGNALS FROM
THE MASTER
SIGNALS FROM
THE SLAVE
A
C
K
1
0
1
0
0
A
C
K
WRITE
SIGNAL AT SDA
0 0 0 0
A0
A1
A2
FIGURE 18. BYTE WRITE SEQUENCE
ISL22326
相关PDF资料 |
PDF描述 |
|---|---|
| ISL22329 | Low Noise, Low Power, I2C Bus, 128 Taps, Wiper Only(低噪声,低功率，I2C总线, 128抽头电位器) |
| ISL22346 | Low Noise, Low Power I2C Bus, 128 Taps(低噪声,低功率，I2C总线, 128抽头电位器) |
| ISL22349 | Low Noise, Low Power, I2C Bus, 128 Taps, Wiper Only(低噪声,低功率，I2C总线, 128抽头电位器) |
| ISL23710UIU10Z | Terminal Voltage +-3V or +-5V, 128 Taps Up/Down Interface |
| ISL23710WIU10Z | Terminal Voltage +-3V or +-5V, 128 Taps Up/Down Interface |
相关代理商/技术参数 |
参数描述 |
|---|---|
| ISL22326UFR16Z | 功能描述:数字电位计 IC 128 TAP FL RNG IND DL DCP 16LD 4X4 RoHS:否 制造商:Maxim Integrated 电阻:200 Ohms 温度系数:35 PPM / C 容差:25 % POT 数量:Dual 每 POT 分接头:256 弧刷存储器:Volatile 缓冲刷: 数字接口:Serial (3-Wire, SPI) 描述/功能:Dual Volatile Low Voltage Linear Taper Digital Potentiometer 工作电源电压:1.7 V to 5.5 V 电源电流:27 uA 最大工作温度:+ 125 C 安装风格:SMD/SMT 封装 / 箱体:TQFN-16 封装:Reel |
| ISL22326UFR16Z-TK | 功能描述:数字电位计 IC 128 TAP FL RNG IND DL DCP 16LD 4X4 RoHS:否 制造商:Maxim Integrated 电阻:200 Ohms 温度系数:35 PPM / C 容差:25 % POT 数量:Dual 每 POT 分接头:256 弧刷存储器:Volatile 缓冲刷: 数字接口:Serial (3-Wire, SPI) 描述/功能:Dual Volatile Low Voltage Linear Taper Digital Potentiometer 工作电源电压:1.7 V to 5.5 V 电源电流:27 uA 最大工作温度:+ 125 C 安装风格:SMD/SMT 封装 / 箱体:TQFN-16 封装:Reel |
| ISL22326UFV14Z | 功能描述:数字电位计 IC 128 TAP FL RNG DCP 14LD RoHS:否 制造商:Maxim Integrated 电阻:200 Ohms 温度系数:35 PPM / C 容差:25 % POT 数量:Dual 每 POT 分接头:256 弧刷存储器:Volatile 缓冲刷: 数字接口:Serial (3-Wire, SPI) 描述/功能:Dual Volatile Low Voltage Linear Taper Digital Potentiometer 工作电源电压:1.7 V to 5.5 V 电源电流:27 uA 最大工作温度:+ 125 C 安装风格:SMD/SMT 封装 / 箱体:TQFN-16 封装:Reel |
| ISL22326UFV14Z-TK | 功能描述:数字电位计 IC 128 TAP FL RNG IND DCP 14LD RoHS:否 制造商:Maxim Integrated 电阻:200 Ohms 温度系数:35 PPM / C 容差:25 % POT 数量:Dual 每 POT 分接头:256 弧刷存储器:Volatile 缓冲刷: 数字接口:Serial (3-Wire, SPI) 描述/功能:Dual Volatile Low Voltage Linear Taper Digital Potentiometer 工作电源电压:1.7 V to 5.5 V 电源电流:27 uA 最大工作温度:+ 125 C 安装风格:SMD/SMT 封装 / 箱体:TQFN-16 封装:Reel |
| ISL22326WFR16Z | 功能描述:数字电位计 IC 128 TAP FL RNG DCP 16LD 4X4 RoHS:否 制造商:Maxim Integrated 电阻:200 Ohms 温度系数:35 PPM / C 容差:25 % POT 数量:Dual 每 POT 分接头:256 弧刷存储器:Volatile 缓冲刷: 数字接口:Serial (3-Wire, SPI) 描述/功能:Dual Volatile Low Voltage Linear Taper Digital Potentiometer 工作电源电压:1.7 V to 5.5 V 电源电流:27 uA 最大工作温度:+ 125 C 安装风格:SMD/SMT 封装 / 箱体:TQFN-16 封装:Reel |
发布紧急采购，3分钟左右您将得到回复。