参数资料
| 型号： | ISL22424TFV14Z |
| 厂商： | Intersil |
| 文件页数： | 5/18页 |
| 文件大小： | 0K |
| 描述： | IC POT DGTL 256TP LN LP 14-TSSOP |
| 标准包装： | 960 |
| 系列： | XDCP™ |
| 接片： | 256 |
| 电阻（欧姆）： | 100k |
| 电路数： | 2 |
| 温度系数： | 标准值 ±45 ppm/°C |
| 存储器类型： | 非易失 |
| 接口： | 4 线 SPI（芯片选择） |
| 电源电压： | 2.25 V ~ 5.5 V |
| 工作温度： | -40°C ~ 125°C |
| 安装类型： | 表面贴装 |
| 封装/外壳： | 14-TSSOP（0.173"，4.40mm 宽） |
| 供应商设备封装： | 14-TSSOP |
| 包装： | 管件 |
13
FN6425.0
May 31, 2007
controlled by the host or master. The ISL22424 operates
only as a slave device.
All communication over the SPI interface is conducted by
sending the MSB of each byte of data first.
Protocol Conventions
The SPI protocol contains Instruction Byte followed by one
or more Data Bytes. A valid Instruction Byte contains
instruction as the three MSBs, with the following five register
address bits (see Table 3).
The next byte sent to the ISL22424 is the Data Byte.
TABLE 3. INSTRUCTION BYTE FORMAT
Table 4 contains a valid instruction set for ISL22424.
There are only sixteen register addresses possible for this
DCP. If the [R4:R0] bits are 00000 or 00001, then the read or
write is to either the IVRi or the WRi registers (depends of
VOL bit at ACR). If the [R4:R0] are 10000, then the
operation is on the ACR.
Write Operation
A Write operation to the ISL22424 is a two or more bytes
operation. First, It requires, the CS transition from HIGH to
LOW. Then host must send a valid Instruction Byte followed
by one or more Data Bytes to SDI pin. The host terminates
the write operation by pulling the CS pin from LOW to HIGH.
Instruction is executed on rising edge of CS. For a write-to
address 0 or 1, the MSB of the byte at address 10h (ACR[7])
determines if the Data Byte is to be written to volatile or both
volatile and non-volatile registers. Refer to “Memory
Description” and Figure 16. Note: the internal non-volatile
write cycle starts with the rising edge of CS and requires up
to 20ms. During non-volatile write cycle the read operation to
ACR register is allowed to check WIP bit.
Read Operation
A Read operation to the ISL22424 is a four byte operation. It
requires first, the CS transition from HIGH to LOW. Then the
host must send a valid Instruction Byte followed by “dummy”
Data Byte, a NOP Instruction Byte and another “dummy”
Data Byte to SDI pin. The SPI host receives the Instruction
Byte (instruction code + register address) and requested
Data Byte from SDO pin on rising edge of SCK during third
and fourth bytes respectively. The host terminates the read
operation by pulling the CS pin from LOW to HIGH (see
Figure 17). Reading from the IVRi will not change the WRi, if
its contents are different.
BIT #
76
54
32
1
0
I2
I1
I0
R4
R3
R2
R1
R0
TABLE 4. INSTRUCTION SET
INSTRUCTION SET
OPERATION
I2
I1
I0
R4
R3
R2
R1
R0
0
XXXX
X
NOP
0
1
XXXX
X
ACR READ
0
1
XXXX
X
ACR WRITE
1
0
R4
R3
R2
R1
R0
WR, IVR, GP or ACR READ
1
0
R4
R3
R2
R1
R0
WR, IVR, GP or ACR WRITE
where X means “do not care”.
FIGURE 16. TWO BYTE WRITE SEQUENCE
CS
SCK
SDI
SDO
WR INSTRUCTION
DATA BYTE
1
3
4
5
7
8
9
1011
1213141516
26
ADDR
ISL22424
相关PDF资料 |
PDF描述 |
|---|---|
| ADF4154BRUZ-RL7 | IC FRACTION-N FREQ SYNTH 16TSSOP |
| SY100EL57ZG | IC MULTIPLXR 4:1/2:1 DIFF 16SOIC |
| VE-JT4-MZ-S | CONVERTER MOD DC/DC 48V 25W |
| SY100EP57VK4G TR | IC MUX DIFF 4:1 3.3V/5V 20-TSSOP |
| ISL22424UFV14Z | IC POT DGTL 256TP LN LP 14-TSSOP |
相关代理商/技术参数 |
参数描述 |
|---|---|
| ISL22424TFV14Z-TK | 功能描述:数字电位计 IC 256 TAP FL RNG IND DL SPI DCP 14LD RoHS:否 制造商:Maxim Integrated 电阻:200 Ohms 温度系数:35 PPM / C 容差:25 % POT 数量:Dual 每 POT 分接头:256 弧刷存储器:Volatile 缓冲刷: 数字接口:Serial (3-Wire, SPI) 描述/功能:Dual Volatile Low Voltage Linear Taper Digital Potentiometer 工作电源电压:1.7 V to 5.5 V 电源电流:27 uA 最大工作温度:+ 125 C 安装风格:SMD/SMT 封装 / 箱体:TQFN-16 封装:Reel |
| ISL22424UFR16Z | 功能描述:数字电位计 IC 256 TAP FL RNG IND DL SPI DCP 4X4 RoHS:否 制造商:Maxim Integrated 电阻:200 Ohms 温度系数:35 PPM / C 容差:25 % POT 数量:Dual 每 POT 分接头:256 弧刷存储器:Volatile 缓冲刷: 数字接口:Serial (3-Wire, SPI) 描述/功能:Dual Volatile Low Voltage Linear Taper Digital Potentiometer 工作电源电压:1.7 V to 5.5 V 电源电流:27 uA 最大工作温度:+ 125 C 安装风格:SMD/SMT 封装 / 箱体:TQFN-16 封装:Reel |
| ISL22424UFR16Z-TK | 功能描述:数字电位计 IC 256 TAP FL RNG IND DL SPI DCP 4X4 RoHS:否 制造商:Maxim Integrated 电阻:200 Ohms 温度系数:35 PPM / C 容差:25 % POT 数量:Dual 每 POT 分接头:256 弧刷存储器:Volatile 缓冲刷: 数字接口:Serial (3-Wire, SPI) 描述/功能:Dual Volatile Low Voltage Linear Taper Digital Potentiometer 工作电源电压:1.7 V to 5.5 V 电源电流:27 uA 最大工作温度:+ 125 C 安装风格:SMD/SMT 封装 / 箱体:TQFN-16 封装:Reel |
| ISL22424UFV14Z | 功能描述:数字电位计 IC 256 TAP FL RNG IND DL SPI DCP 14LD RoHS:否 制造商:Maxim Integrated 电阻:200 Ohms 温度系数:35 PPM / C 容差:25 % POT 数量:Dual 每 POT 分接头:256 弧刷存储器:Volatile 缓冲刷: 数字接口:Serial (3-Wire, SPI) 描述/功能:Dual Volatile Low Voltage Linear Taper Digital Potentiometer 工作电源电压:1.7 V to 5.5 V 电源电流:27 uA 最大工作温度:+ 125 C 安装风格:SMD/SMT 封装 / 箱体:TQFN-16 封装:Reel |
| ISL22424UFV14Z-TK | 功能描述:数字电位计 IC 256 TAP FL RNG IND DL SPI DCP 14LD RoHS:否 制造商:Maxim Integrated 电阻:200 Ohms 温度系数:35 PPM / C 容差:25 % POT 数量:Dual 每 POT 分接头:256 弧刷存储器:Volatile 缓冲刷: 数字接口:Serial (3-Wire, SPI) 描述/功能:Dual Volatile Low Voltage Linear Taper Digital Potentiometer 工作电源电压:1.7 V to 5.5 V 电源电流:27 uA 最大工作温度:+ 125 C 安装风格:SMD/SMT 封装 / 箱体:TQFN-16 封装:Reel |
发布紧急采购，3分钟左右您将得到回复。