参数资料
| 型号： | ISL23418TFUZ-T7A |
| 厂商： | Intersil |
| 文件页数： | 6/20页 |
| 文件大小： | 0K |
| 描述： | IC DGTL POT 1CH 100K 10MSOP |
| 标准包装： | 1 |
| 系列： | XDCP™ |
| 接片： | 128 |
| 电阻（欧姆）： | 100k |
| 电路数： | 1 |
| 温度系数： | 标准值 70 ppm/°C |
| 存储器类型： | 易失 |
| 接口： | 4 线 SPI（芯片选择） |
| 电源电压： | 1.2 V ~ 5.5 V，1.7 V ~ 5.5 V |
| 工作温度： | -40°C ~ 125°C |
| 安装类型： | 表面贴装 |
| 封装/外壳： | 10-TFSOP，10-MSOP（0.118"，3.00mm 宽） |
| 供应商设备封装： | 10-MSOP |
| 包装： | 标准包装 |
| 其它名称： | ISL23418TFUZ-T7ADKR |
ISL23418
14
FN7901.0
August 3, 2011
In shutdown mode, the RW terminal is shorted to the RL terminal
with around 2k resistance, as shown in Figure 25. When the device
enters shutdown, all current DCP WR settings are maintained. When
the device exits shutdown, the wipers return to the previous WR
settings after a short settling time (Figure 26).
In shutdown mode, if there is a glitch in the power supply that
causes it to drop below 1.3V for more than 0.2s to 0.4s, the
wipers are RESET to their mid position. This is done to avoid an
undefined state at the wiper outputs.
SPI Serial Interface
The ISL23418 supports an SPI serial protocol, mode 0. The
device is accessed via the SDI input and SDO output, with data
clocked in on the rising edge of SCK and clocked out on the
falling edge of SCK. CS must be LOW during communication with
the ISL23418. The SCK and CS lines are controlled by the host or
master. The ISL23418 operates only as a slave device. All
communication over the SPI interface is conducted by sending
the MSB of each byte of data first.
Protocol Conventions
The SPI protocol contains an Instruction Byte followed by one or
more Data Bytes. A valid Instruction Byte contains instruction as
the three MSBs, with the following five register address bits
(Table 3). The next byte sent to the ISL23418 is the Data Byte.
Table 4 contains a valid instruction set for ISL23418. If the
[R4:R0] bits are zero, then the read or write is to the WR register. If
the [R4:R0] bits are 10000, then the operation is to the ACR.
Write Operation
A write operation to the ISL23418 is a two or more bytes
operation. It first requires CS to transition from HIGH to LOW.
Then the host sends a valid Instruction Byte to the SDI pin,
followed by one or more Data Bytes. The host terminates the
write operation by pulling the CS pin from LOW to HIGH. The
instruction is executed on the rising edge of CS (Figure 27).
Read Operation
A read operation to the ISL23418 is a four-byte operation. First,
the CS transitions from HIGH to LOW. Then the host sends a valid
Instruction Byte to the SDI pin, followed by a “dummy” Data Byte,
an NOP Instruction Byte, and another “dummy” Data Byte. The
SPI host receives the Instruction Byte (instruction code + register
address) and the requested Data Byte from the SDO pin on the
rising edge of SCK during the third and fourth bytes, respectively.
The host terminates the read by pulling the CS pin from LOW to
HIGH (Figure 28).
FIGURE 25. DCP CONNECTION IN SHUTDOWN MODE
2k
RW
RL
RH
POWER-UP
USER PROGRAMMED
MID SCALE = 40H
SHDN ACTIVATED SHDN RELEASED
AFTER SHDN
WIP
E
R
VOL
TAGE
,V
RW
(V
)
SHDN MODE
TIME (s)
WIPER RESTORE TO
ORIGINAL POSITION
0
FIGURE 26. SHUTDOWN MODE WIPER RESPONSE
TABLE 3. INSTRUCTION BYTE FORMAT
BIT #
7
654321
0
I2
I1
I0
R4
R3
R2
R1
R0
TABLE 4. INSTRUCTION SET
INSTRUCTION SET
OPERATION
I2
I1
I0
R4
R3
R2
R1
R0
0
XXX
XX
NOP
0
1
XXX
XX
ACR READ
0
1
XXX
XX
ACR WRTE
1
0
R4R3R2R1R0
WR or ACR READ
1
0
R4R3R2R1R0
WR or ACR WRTE
where “X” means “do not care.”
相关PDF资料 |
PDF描述 |
|---|---|
| D38999/26WH21PA | CONN PLUG 21POS STRAIGHT W/PINS |
| VI-BN1-MW-B1 | CONVERTER MOD DC/DC 12V 100W |
| MS3456W20-15PZ | CONN PLUG 7POS STRAIGHT W/PINS |
| MS3456W20-15PW | CONN PLUG 7POS STRAIGHT W/PINS |
| VI-BN0-MW-B1 | CONVERTER MOD DC/DC 5V 100W |
相关代理商/技术参数 |
参数描述 |
|---|---|
| ISL23418TFUZ-TK | 功能描述:数字电位计 IC 128 TAP VOLATILE SPI SINGLE DCP 10LD RoHS:否 制造商:Maxim Integrated 电阻:200 Ohms 温度系数:35 PPM / C 容差:25 % POT 数量:Dual 每 POT 分接头:256 弧刷存储器:Volatile 缓冲刷: 数字接口:Serial (3-Wire, SPI) 描述/功能:Dual Volatile Low Voltage Linear Taper Digital Potentiometer 工作电源电压:1.7 V to 5.5 V 电源电流:27 uA 最大工作温度:+ 125 C 安装风格:SMD/SMT 封装 / 箱体:TQFN-16 封装:Reel |
| ISL23418UFRUZ-T7A | 功能描述:数字电位计 IC 128 TAPVOLATILE SPI SNG RNG IND DCP 10LD RoHS:否 制造商:Maxim Integrated 电阻:200 Ohms 温度系数:35 PPM / C 容差:25 % POT 数量:Dual 每 POT 分接头:256 弧刷存储器:Volatile 缓冲刷: 数字接口:Serial (3-Wire, SPI) 描述/功能:Dual Volatile Low Voltage Linear Taper Digital Potentiometer 工作电源电压:1.7 V to 5.5 V 电源电流:27 uA 最大工作温度:+ 125 C 安装风格:SMD/SMT 封装 / 箱体:TQFN-16 封装:Reel |
| ISL23418UFRUZ-TK | 功能描述:数字电位计 IC 128 TAP VOLATILE SPI SINGLE DCP 10LD RoHS:否 制造商:Maxim Integrated 电阻:200 Ohms 温度系数:35 PPM / C 容差:25 % POT 数量:Dual 每 POT 分接头:256 弧刷存储器:Volatile 缓冲刷: 数字接口:Serial (3-Wire, SPI) 描述/功能:Dual Volatile Low Voltage Linear Taper Digital Potentiometer 工作电源电压:1.7 V to 5.5 V 电源电流:27 uA 最大工作温度:+ 125 C 安装风格:SMD/SMT 封装 / 箱体:TQFN-16 封装:Reel |
| ISL23418UFUZ | 功能描述:数字电位计 IC 128 TAP VOLATILE SPI SINGLE DCP 10LD RoHS:否 制造商:Maxim Integrated 电阻:200 Ohms 温度系数:35 PPM / C 容差:25 % POT 数量:Dual 每 POT 分接头:256 弧刷存储器:Volatile 缓冲刷: 数字接口:Serial (3-Wire, SPI) 描述/功能:Dual Volatile Low Voltage Linear Taper Digital Potentiometer 工作电源电压:1.7 V to 5.5 V 电源电流:27 uA 最大工作温度:+ 125 C 安装风格:SMD/SMT 封装 / 箱体:TQFN-16 封装:Reel |
| ISL23418UFUZ-T7A | 功能描述:数字电位计 IC 128 TAPVOLATILE SPI SNG RNG IND DCP 10LD RoHS:否 制造商:Maxim Integrated 电阻:200 Ohms 温度系数:35 PPM / C 容差:25 % POT 数量:Dual 每 POT 分接头:256 弧刷存储器:Volatile 缓冲刷: 数字接口:Serial (3-Wire, SPI) 描述/功能:Dual Volatile Low Voltage Linear Taper Digital Potentiometer 工作电源电压:1.7 V to 5.5 V 电源电流:27 uA 最大工作温度:+ 125 C 安装风格:SMD/SMT 封装 / 箱体:TQFN-16 封装:Reel |
发布紧急采购，3分钟左右您将得到回复。