参数资料
| 型号： | ISL23428TFVZ |
| 厂商： | Intersil |
| 文件页数： | 6/21页 |
| 文件大小： | 0K |
| 描述： | IC DGTL POT 2CH 100K 14TSSOP |
| 标准包装： | 960 |
| 系列： | XDCP™ |
| 接片： | 128 |
| 电阻（欧姆）： | 100k |
| 电路数： | 2 |
| 温度系数： | 标准值 45 ppm/°C |
| 存储器类型： | 易失 |
| 接口： | 4 线 SPI（芯片选择） |
| 电源电压： | 1.2 V ~ 5.5 V，1.7 V ~ 5.5 V |
| 工作温度： | -40°C ~ 125°C |
| 安装类型： | 表面贴装 |
| 封装/外壳： | 14-TSSOP（0.173"，4.40mm 宽） |
| 供应商设备封装： | 14-TSSOP |
| 包装： | 管件 |
ISL23428
14
FN7904.1
July 19, 2012
SERIAL DATA OUTPUT (SDO)
The SDO is a serial data output pin. During a read cycle, the data
bits are shifted out on the falling edge of the serial clock SCK and
will be available to the master on the following rising edge of SCK.
The output type is configured through ACR[1] bit for Push-Pull or
Open Drain operation. Default setting for this pin is Push-Pull. An
external pull-up resistor is required for Open Drain output
operation. When CS is HIGH, the SDO pin is in tri-state (Z) or
high-tri-state (Hi-Z) depends on the selected configuration.
CHIP SELECT (CS)
CS LOW enables the ISL23428, placing it in the active power
mode. A HIGH to LOW transition on CS is required prior to the
start of any operation after power-up. When CS is HIGH, the
ISL23428 is deselected and the SDO pin is at high impedance,
and the device will be in the standby state.
VLOGIC
Digital power source for the logic control section. It supplies an
internal level translator for 1.2V to 5.5V serial bus operation. Use
the same supply as the I2C logic source.
Principles of Operation
The ISL23428 is an integrated circuit incorporating two DCPs
with its associated registers and an SPI serial interface providing
direct communication between a host and the potentiometer.
The resistor array is comprised of individual resistors connected
in series. At either end of the array and between each resistor is
an electronic switch that transfers the potential at that point to
the wiper.
The electronic switches on the device operate in a
“make-before-break” mode when the wiper changes tap
positions.
Voltage at any DCP pins, RHi, RLi or RWi, should not exceed VCC
level at any conditions during power-up and normal operation.
The VLOGIC pin is the terminal for the logic control digital power
source. It should use the same supply as the SPI logic source
which allows reliable communication with a wide range of
microcontrollers and is independent from the VCC level. This is
extremely important in systems where the master supply has
lower levels than DCP analog supply.
DCP Description
Each DCP is implemented with a combination of resistor
elements and CMOS switches. The physical ends of each DCP are
equivalent to the fixed terminals of a mechanical potentiometer
(RHi and RLi pins). The RWi pin of the DCP is connected to
intermediate nodes, and is equivalent to the wiper terminal of a
mechanical potentiometer. The position of the wiper terminal
within the DCP is controlled by an 8-bit volatile Wiper Register
(WRi). When the WR of a DCP contains all zeroes
(WRi[7:0] = 00h), its wiper terminal (RWi) is closest to its “Low”
terminal (RLi). When the WRi register of a DCP contains all ones
(WRi[7:0] = 7Fh), its wiper terminal (RWi) is closest to its “High”
terminal (RHi). As the value of the WRi increases from all zeroes
(0) to all ones (127 decimal), the wiper moves monotonically
from the position closest to RLi to the position closest to RHi. At
the same time, the resistance between RWi and RLi increases
monotonically, while the resistance between RHi and RWi
decreases monotonically.
While the ISL23428 is being powered up, both WRi are reset to
40h (64 decimal), which positions RWi at the center between RLi
and RHi.
The WRi can be read or written to directly using the SPI serial
interface, as described in the following sections.
Memory Description
The ISL23428 contains three volatile 8-bit registers: Wiper Register
WR0, Wiper Register WR1, and Access Control Register (ACR).
Memory map of ISL23428 is shown in Table 1. The Wiper Register
WR0 at address 0 contains current wiper position of DCP0; the
Wiper Register WR1 at address 1 contains current wiper position of
DCP1. The Access Control Register (ACR) at address 10h contains
information and control bits described in Table 2.
The SDO bit (ACR[1]) configures type of SDO output pin. The
default value of SDO bit is 0 for Push-Pull output. The SDO pin
can be configured as Open Drain output for some applications. In
this case, an external pull-up resistor is required; reference the
Shutdown Function
The SHDN bit (ACR[6]) disables or enables shutdown mode for all
DCP channels simultaneously. When this bit is 0, i.e., each DCP is
forced to end-to-end open circuit and each RW shorted to RL
through a 2k serial resistor, as shown in Figure 25. Default value
of the SHDN bit is 1.
TABLE 1. MEMORY MAP
ADDRESS
(hex)
VOLATILE
REGISTER NAME
DEFAULT SETTING
(hex)
10
ACR
40
1WR1
40
0WR0
40
TABLE 2. ACCESS CONTROL REGISTER (ACR)
BIT #
7
6
5
4
32
10
NAME/
VALUE
0SHDN
00
0
SDO
0
FIGURE 25. DCP CONNECTION IN SHUTDOWN MODE
2k
RW
RL
RH
相关PDF资料 |
PDF描述 |
|---|---|
| SY10E196JC | IC DELAY LINE 7TAP 28-PLCC |
| VI-2TJ-MW | CONVERTER MOD DC/DC 36V 100W |
| MS3450L22-18SX | CONN RCPT 8POS WALL MNT W/SCKT |
| VE-B6W-MY-F2 | CONVERTER MOD DC/DC 5.5V 50W |
| SY10E195JC TR | IC DELAY LINE 128TAP 28-PLCC |
相关代理商/技术参数 |
参数描述 |
|---|---|
| ISL23428TFVZ-T7A | 功能描述:数字电位计 IC 128 TAPVOLATILE SPI DUAL RNG IND 14LD RoHS:否 制造商:Maxim Integrated 电阻:200 Ohms 温度系数:35 PPM / C 容差:25 % POT 数量:Dual 每 POT 分接头:256 弧刷存储器:Volatile 缓冲刷: 数字接口:Serial (3-Wire, SPI) 描述/功能:Dual Volatile Low Voltage Linear Taper Digital Potentiometer 工作电源电压:1.7 V to 5.5 V 电源电流:27 uA 最大工作温度:+ 125 C 安装风格:SMD/SMT 封装 / 箱体:TQFN-16 封装:Reel |
| ISL23428TFVZ-TK | 功能描述:数字电位计 IC 128 TAP VOLATILE SPI DL FL RNG DCP 14LD RoHS:否 制造商:Maxim Integrated 电阻:200 Ohms 温度系数:35 PPM / C 容差:25 % POT 数量:Dual 每 POT 分接头:256 弧刷存储器:Volatile 缓冲刷: 数字接口:Serial (3-Wire, SPI) 描述/功能:Dual Volatile Low Voltage Linear Taper Digital Potentiometer 工作电源电压:1.7 V to 5.5 V 电源电流:27 uA 最大工作温度:+ 125 C 安装风格:SMD/SMT 封装 / 箱体:TQFN-16 封装:Reel |
| ISL23428UFRUZ-T7A | 功能描述:数字电位计 IC 128 TAPVOLATILE SPI DUAL RNG IND 16LD RoHS:否 制造商:Maxim Integrated 电阻:200 Ohms 温度系数:35 PPM / C 容差:25 % POT 数量:Dual 每 POT 分接头:256 弧刷存储器:Volatile 缓冲刷: 数字接口:Serial (3-Wire, SPI) 描述/功能:Dual Volatile Low Voltage Linear Taper Digital Potentiometer 工作电源电压:1.7 V to 5.5 V 电源电流:27 uA 最大工作温度:+ 125 C 安装风格:SMD/SMT 封装 / 箱体:TQFN-16 封装:Reel |
| ISL23428UFRUZ-TK | 功能描述:数字电位计 IC 128 TAP VOLATILE SPI DL FL RNG DCP 16LD RoHS:否 制造商:Maxim Integrated 电阻:200 Ohms 温度系数:35 PPM / C 容差:25 % POT 数量:Dual 每 POT 分接头:256 弧刷存储器:Volatile 缓冲刷: 数字接口:Serial (3-Wire, SPI) 描述/功能:Dual Volatile Low Voltage Linear Taper Digital Potentiometer 工作电源电压:1.7 V to 5.5 V 电源电流:27 uA 最大工作温度:+ 125 C 安装风格:SMD/SMT 封装 / 箱体:TQFN-16 封装:Reel |
| ISL23428UFVZ | 功能描述:数字电位计 IC 128 TAP VOLATILE SPI DL FL RNG DCP 14LD RoHS:否 制造商:Maxim Integrated 电阻:200 Ohms 温度系数:35 PPM / C 容差:25 % POT 数量:Dual 每 POT 分接头:256 弧刷存储器:Volatile 缓冲刷: 数字接口:Serial (3-Wire, SPI) 描述/功能:Dual Volatile Low Voltage Linear Taper Digital Potentiometer 工作电源电压:1.7 V to 5.5 V 电源电流:27 uA 最大工作温度:+ 125 C 安装风格:SMD/SMT 封装 / 箱体:TQFN-16 封装:Reel |
发布紧急采购，3分钟左右您将得到回复。