参数资料
| 型号： | ISL23428UFRUZ-T7A |
| 厂商： | Intersil |
| 文件页数： | 9/21页 |
| 文件大小： | 0K |
| 描述： | IC DGTL POT 2CH 50K 16UTQFN |
| 标准包装： | 1 |
| 系列： | XDCP™ |
| 接片： | 128 |
| 电阻（欧姆）： | 50k |
| 电路数： | 2 |
| 温度系数： | 标准值 65 ppm/°C |
| 存储器类型： | 易失 |
| 接口： | 4 线 SPI（芯片选择） |
| 电源电压： | 1.2 V ~ 5.5 V，1.7 V ~ 5.5 V |
| 工作温度： | -40°C ~ 125°C |
| 安装类型： | 表面贴装 |
| 封装/外壳： | 16-UFQFN |
| 供应商设备封装： | 16-UTQFN（2.6x1.8） |
| 包装： | 标准包装 |
| 其它名称： | ISL23428UFRUZ-T7ADKR |
ISL23428
17
FN7904.1
July 19, 2012
Applications Information
Communicating with ISL23428
Communication with ISL23428 proceeds using SPI interface
through the ACR (address 10000b), WR0 (addresses 00000b)
and WR1 (addresses 00001b) registers.
The wiper of the potentiometer is controlled by the WRi register.
Writes and reads can be made directly to these registers to
control and monitor the wiper position.
Daisy Chain Configuration
When an application needs more than one ISL23428, it can
communicate with all of them without additional CS lines by
daisy chaining the DCPs as shown in Figure 29. In Daisy Chain
configuration, the SDO pin of the previous chip is connected to
the SDI pin of the following chip, and each CS and SCK pins are
connected to the corresponding microcontroller pins in parallel,
like regular SPI interface implementation. The Daisy Chain
configuration can also be used for simultaneous setting of
multiple DCPs.
NOTE: The number of daisy chained DCPs is limited only by the driving
capabilities of the SCK and CS pins of the microcontroller; for larger
number of SPI devices, buffering of SCK and CS lines is required.
Daisy Chain Write Operation
The write operation starts by HIGH-to-LOW transition on CS line,
followed by N number of two bytes write instructions on SDI line
with reversed chain access sequence: the instruction byte + data
byte for the last DCP in chain is going first, as shown in Figure 30,
where N is a number of DCPs in chain. The serial data is going
through DCPs from DCP0 to DCP(N-1) as follows: DCP0 --> DCP1 -->
DCP2 --> ... --> DCP(N-1). The write instruction is executed on the
rising edge of CS for all N DCPs simultaneously.
Daisy Chain Read Operation
The read operation consists of two parts: first, send the read
instructions (N two bytes operation) with valid address; second,
read the requested data while sending NOP instructions (N two
The first part starts by HIGH-to-LOW transition on CS line,
followed by N two bytes read instruction on SDI line with reversed
chain access sequence: the instruction byte + dummy data byte
for the last DCP in chain is going first, followed by LOW-to-HIGH
transition on CS line. The read instructions are executed during
the second part of read sequence. It also starts by HIGH-to-LOW
transition on CS line, followed by N number of two bytes NOP
instructions on SDI line and LOW-to-HIGH transition of CS. The
data is read on every even byte during the second part of the
read sequence while every odd byte contains code 111b followed
by address from which the data is being read.
Wiper Transition
When stepping up through each tap in voltage divider mode,
some tap transition points can result in noticeable voltage
transients, or overshoot/undershoot, resulting from the sudden
transition from a very low impedance “make” to a much higher
impedance “break” within a short period of time (<1s). There
are several code transitions such as 0Fh to 10h, 1Fh to 20h,...,
6Fh to 7Fh, which have higher transient glitch.
NOTE: That all switching transients will settle well within the settling time
as stated in the datasheet. A small capacitor can be added externally to
reduce the amplitude of these voltage transients, but that will also reduce
the useful bandwidth of the circuit, thus this may not be a good solution
for some applications. It may be a good idea, in that case, to use fast
amplifiers in a signal chain for fast recovery.
VLOGIC Requirements
It is recommended to keep VLOGIC powered all the time during
normal operation. In a case where turning VLOGIC OFF is
necessary, it is recommended to ground the VLOGIC pin of the
ISL23428. Grounding the VLOGIC pin or both VLOGIC and VCC does
not affect other devices on the same bus. It is good practice to put
a 1F capacitor in parallel with 0.1F decoupling capacitor close to
the VLOGIC pin.
VCC Requirements and Placement
It is recommended to put a 1F capacitor in parallel with 0.1F
decoupling capacitor close to the VCC pin.
CS
SCK
MOSI
MISO
CS
SCK
SDI
SDO
CS
SCK
SDI
SDO
CS
SCK
SDI
SDO
CS
SCK
SDI
SDO
C
DCP0
DCP1
DCP2
DCP(N-1)
FIGURE 29. DAISY CHAIN CONFIGURATION
N DCP IN A CHAIN
相关PDF资料 |
PDF描述 |
|---|---|
| VI-23B-MY-F1 | CONVERTER MOD DC/DC 95V 50W |
| DS1341U+ | IC RTC I2C W/ALARM 8USOP |
| VI-BNR-MW-B1 | CONVERTER MOD DC/DC 7.5V 100W |
| VI-BNR-MV | CONVERTER MOD DC/DC 7.5V 150W |
| ISL23315WFRUZ-T7A | IC DGTL POT 256POS 10K 10TQFN |
相关代理商/技术参数 |
参数描述 |
|---|---|
| ISL23428UFRUZ-TK | 功能描述:数字电位计 IC 128 TAP VOLATILE SPI DL FL RNG DCP 16LD RoHS:否 制造商:Maxim Integrated 电阻:200 Ohms 温度系数:35 PPM / C 容差:25 % POT 数量:Dual 每 POT 分接头:256 弧刷存储器:Volatile 缓冲刷: 数字接口:Serial (3-Wire, SPI) 描述/功能:Dual Volatile Low Voltage Linear Taper Digital Potentiometer 工作电源电压:1.7 V to 5.5 V 电源电流:27 uA 最大工作温度:+ 125 C 安装风格:SMD/SMT 封装 / 箱体:TQFN-16 封装:Reel |
| ISL23428UFVZ | 功能描述:数字电位计 IC 128 TAP VOLATILE SPI DL FL RNG DCP 14LD RoHS:否 制造商:Maxim Integrated 电阻:200 Ohms 温度系数:35 PPM / C 容差:25 % POT 数量:Dual 每 POT 分接头:256 弧刷存储器:Volatile 缓冲刷: 数字接口:Serial (3-Wire, SPI) 描述/功能:Dual Volatile Low Voltage Linear Taper Digital Potentiometer 工作电源电压:1.7 V to 5.5 V 电源电流:27 uA 最大工作温度:+ 125 C 安装风格:SMD/SMT 封装 / 箱体:TQFN-16 封装:Reel |
| ISL23428UFVZ-T7A | 功能描述:数字电位计 IC 128 TAPVOLATILE SPI DUAL RNG IND 14LD RoHS:否 制造商:Maxim Integrated 电阻:200 Ohms 温度系数:35 PPM / C 容差:25 % POT 数量:Dual 每 POT 分接头:256 弧刷存储器:Volatile 缓冲刷: 数字接口:Serial (3-Wire, SPI) 描述/功能:Dual Volatile Low Voltage Linear Taper Digital Potentiometer 工作电源电压:1.7 V to 5.5 V 电源电流:27 uA 最大工作温度:+ 125 C 安装风格:SMD/SMT 封装 / 箱体:TQFN-16 封装:Reel |
| ISL23428UFVZ-TK | 功能描述:数字电位计 IC 128 TAP VOLATILE SPI DL FL RNG DCP 14LD RoHS:否 制造商:Maxim Integrated 电阻:200 Ohms 温度系数:35 PPM / C 容差:25 % POT 数量:Dual 每 POT 分接头:256 弧刷存储器:Volatile 缓冲刷: 数字接口:Serial (3-Wire, SPI) 描述/功能:Dual Volatile Low Voltage Linear Taper Digital Potentiometer 工作电源电压:1.7 V to 5.5 V 电源电流:27 uA 最大工作温度:+ 125 C 安装风格:SMD/SMT 封装 / 箱体:TQFN-16 封装:Reel |
| ISL23428WFRUZ-T7A | 功能描述:数字电位计 IC 128 TAPVOLATILE SPI DUAL RNG IND 16LD RoHS:否 制造商:Maxim Integrated 电阻:200 Ohms 温度系数:35 PPM / C 容差:25 % POT 数量:Dual 每 POT 分接头:256 弧刷存储器:Volatile 缓冲刷: 数字接口:Serial (3-Wire, SPI) 描述/功能:Dual Volatile Low Voltage Linear Taper Digital Potentiometer 工作电源电压:1.7 V to 5.5 V 电源电流:27 uA 最大工作温度:+ 125 C 安装风格:SMD/SMT 封装 / 箱体:TQFN-16 封装:Reel |
发布紧急采购，3分钟左右您将得到回复。