- 您现在的位置：买卖IC网 > PDF目录17645 > ISL23445WFVZ (Intersil)IC DGTL POT 256POS 10K 20TSSOP PDF资料下载
参数资料
| 型号： | ISL23445WFVZ |
| 厂商： | Intersil |
| 文件页数： | 6/20页 |
| 文件大小： | 0K |
| 描述： | IC DGTL POT 256POS 10K 20TSSOP |
| 产品培训模块： | Solutions for Industrial Control Applications |
| 标准包装： | 740 |
| 系列： | XDCP™ |
| 接片： | 256 |
| 电阻（欧姆）： | 10k |
| 电路数： | 4 |
| 温度系数： | 标准值 125 ppm/°C |
| 存储器类型： | 易失 |
| 接口： | 4 线 SPI（芯片选择） |
| 电源电压： | 1.2 V ~ 5.5 V，1.7 V ~ 5.5 V |
| 工作温度： | -40°C ~ 125°C |
| 安装类型： | * |
| 封装/外壳： | * |
| 供应商设备封装： | * |
| 包装： | * |
ISL23445
14
FN7874.0
June 21, 2011
SERIAL DATA OUTPUT (SDO)
The SDO is a serial data output pin. During a read cycle, the data
bits are shifted out on the falling edge of the serial clock SCK and
will be available to the master on the following rising edge of SCK.
The output type is configured through ACR[1] bit for Push-Pull or
Open Drain operation. The default setting for this pin is Push-Pull.
An external pull-up resistor is required for Open Drain output
operation. When CS is HIGH, the SDO pin is in tri-state (Z) or
high-tri-state (Hi-Z) depending on the selected configuration.
CHIP SELECT (CS)
CS LOW enables the ISL23445, placing it in the active power
mode. A HIGH to LOW transition on CS is required prior to the
start of any operation after power-up. When CS is HIGH, the
ISL23445 is deselected and the SDO pin is at high impedance,
and the device will be in the standby state.
VLOGIC
Digital power source for the logic control section. It supplies an
internal level translator for 1.2V to 5.5V serial bus operation. Use
the same supply as the I2C logic source.
Principles of Operation
The ISL23445 is an integrated circuit incorporating four DCPs
with its associated registers and an SPI serial interface providing
direct communication between a host and the potentiometer.
The resistor array is comprised of individual resistors connected
in series. At either end of the array and between each resistor is
an electronic switch that transfers the potential at that point to
the wiper.
The electronic switches on the device operate in a
“make-before-break” mode when the wiper changes tap
positions.
Voltage at any of the DCP pins, RHi, RLi or RWi, should not
exceed VCC level at any conditions during power-up and normal
operation.
The VLOGIC pin is the terminal for the logic control digital power
source. It should use the same supply as the SPI logic source,
which allows reliable communication with a wide range of
microcontrollers and is independent from the VCC level. This is
extremely important in systems where the master supply has
lower levels than the DCP analog supply.
DCP Description
Each DCP is implemented with a combination of resistor elements
and CMOS switches. The physical ends of each DCP are equivalent
to the fixed terminals of a mechanical potentiometer (RHi and RLi
pins). The RWi pin of the DCP is connected to intermediate nodes,
and is equivalent to the wiper terminal of a mechanical
potentiometer. The position of the wiper terminal within the DCP is
controlled by an 8-bit volatile Wiper Register (WRi). When the WR of
a DCP contains all zeroes (WRi[7:0] = 00h), its wiper terminal (RWi)
is closest to its “Low” terminal (RLi). When the WRi register of a DCP
contains all ones (WRi[7:0] = FFh), its wiper terminal (RWi) is closest
to its “High” terminal (RHi). As the value of the WRi increases from
all zeroes (0) to all ones (255 decimal), the wiper moves
monotonically from the position closest to RLi to the position closest
to RHi. At the same time, the resistance between RWi and RLi
increases monotonically, while the resistance between RHi and RWi
decreases monotonically.
While the ISL23445 is being powered up, both WRi are reset to
80h (128 decimal), which positions RWi at the center between
RLi and RHi.
The WRi can be read or written to directly using the SPI serial
interface as described in the following sections.
Memory Description
The ISL23445 contains five volatile 8-bit registers: Wiper Register
WR0, Wiper Register WR1, Wiper Register WR2, Wiper Register
WR3 and Access Control Register (ACR). The memory map of
ISL23445 is shown in Table 1. The Wiper Register WRi at address i,
contains current wiper position of DCPi (i = 0, 1, 2, 3). The Access
Control Register (ACR) at address 10h contains information and
control bits described in Table 2.
The SDO bit (ACR[1]) configures the type of SDO output pin. The
default value of SDO bit is 0 for Push-Pull output. The SDO pin
can be configured as Open Drain output for some applications. In
this case, an external pull-up resistor is required. Reference the
“Serial Interface Specification” on page 7.
Shutdown Function
The SHDN bit (ACR[6]) disables or enables shutdown mode for all
DCP channels simultaneously. When this bit is 0, i.e. each DCP is
forced to end-to-end open circuit and each RW shorted to RL
through a 2k
Ω serial resistor, as shown in Figure 25. The default
value of the SHDN bit is 1.
TABLE 1. MEMORY MAP
ADDRESS
(hex)
VOLATILE
REGISTER NAME
DEFAULT SETTING
(hex)
10
ACR
40
3WR3
80
2WR2
80
1WR1
80
0WR0
80
TABLE 2. ACCESS CONTROL REGISTER (ACR)
BIT #
7
6
5
4
32
10
NAME/
VALUE
0SHDN
00
0
SDO
0
FIGURE 25. DCP CONNECTION IN SHUTDOWN MODE
2k
RW
RL
RH
相关PDF资料 |
PDF描述 |
|---|---|
| B32652A0223J | CAP FILM 0.022UF 1KVDC RADIAL |
| B32021A3472M | CAP FILM 4700PF 1.5KVDC RADIAL |
| ISL23445UFVZ | IC DGTL POT 256POS 50K 20TSSOP |
| B32922C3224M | CAP FILM 0.22UF 310VAC RADIAL |
| ISL23445TFVZ | IC DGTL POT 256POS 100K 20TSSOP |
相关代理商/技术参数 |
参数描述 |
|---|---|
| ISL23445WFVZ-T7A | 功能描述:数字电位计 IC 256 TAPVOLATILE SPI QUAD FL RNG IND 20LD RoHS:否 制造商:Maxim Integrated 电阻:200 Ohms 温度系数:35 PPM / C 容差:25 % POT 数量:Dual 每 POT 分接头:256 弧刷存储器:Volatile 缓冲刷: 数字接口:Serial (3-Wire, SPI) 描述/功能:Dual Volatile Low Voltage Linear Taper Digital Potentiometer 工作电源电压:1.7 V to 5.5 V 电源电流:27 uA 最大工作温度:+ 125 C 安装风格:SMD/SMT 封装 / 箱体:TQFN-16 封装:Reel |
| ISL23445WFVZ-TK | 功能描述:数字电位计 IC 256 TAP VOLATILE SPI QD FL RNG DCP 20LD RoHS:否 制造商:Maxim Integrated 电阻:200 Ohms 温度系数:35 PPM / C 容差:25 % POT 数量:Dual 每 POT 分接头:256 弧刷存储器:Volatile 缓冲刷: 数字接口:Serial (3-Wire, SPI) 描述/功能:Dual Volatile Low Voltage Linear Taper Digital Potentiometer 工作电源电压:1.7 V to 5.5 V 电源电流:27 uA 最大工作温度:+ 125 C 安装风格:SMD/SMT 封装 / 箱体:TQFN-16 封装:Reel |
| ISL23448 | 制造商:INTERSIL 制造商全称:Intersil Corporation 功能描述:Quad, 128 Tap, Low Voltage Digitally Controlled Potentiometer (XDCPa?￠) |
| ISL23448TFRZ | 功能描述:数字电位计 IC 128 TAP VOLATILE SPI QD FL RNG DCP 20LD RoHS:否 制造商:Maxim Integrated 电阻:200 Ohms 温度系数:35 PPM / C 容差:25 % POT 数量:Dual 每 POT 分接头:256 弧刷存储器:Volatile 缓冲刷: 数字接口:Serial (3-Wire, SPI) 描述/功能:Dual Volatile Low Voltage Linear Taper Digital Potentiometer 工作电源电压:1.7 V to 5.5 V 电源电流:27 uA 最大工作温度:+ 125 C 安装风格:SMD/SMT 封装 / 箱体:TQFN-16 封装:Reel |
| ISL23448TFRZ-T7A | 功能描述:数字电位计 IC 128 TAPVOLATILE SPI QUAD RNG IND 20LD RoHS:否 制造商:Maxim Integrated 电阻:200 Ohms 温度系数:35 PPM / C 容差:25 % POT 数量:Dual 每 POT 分接头:256 弧刷存储器:Volatile 缓冲刷: 数字接口:Serial (3-Wire, SPI) 描述/功能:Dual Volatile Low Voltage Linear Taper Digital Potentiometer 工作电源电压:1.7 V to 5.5 V 电源电流:27 uA 最大工作温度:+ 125 C 安装风格:SMD/SMT 封装 / 箱体:TQFN-16 封装:Reel |
发布紧急采购，3分钟左右您将得到回复。