参数资料
| 型号： | ISL28168FHZ-T7A |
| 厂商： | Intersil |
| 文件页数： | 5/17页 |
| 文件大小： | 0K |
| 描述： | IC OPAMP RRIO SGL 34UA SOT23-6 |
| 标准包装： | 1 |
| 放大器类型： | 通用 |
| 电路数： | 1 |
| 输出类型： | 满摆幅 |
| 转换速率： | 0.1 V/µs |
| 增益带宽积： | 200kHz |
| -3db带宽： | 420kHz |
| 电流 - 输入偏压： | 10pA |
| 电压 - 输入偏移： | 90µV |
| 电流 - 电源： | 34µA |
| 电流 - 输出 / 通道： | 30mA |
| 电压 - 电源，单路/双路(±)： | 2.4 V ~ 5.5 V，±1.2 V ~ 2.75 V |
| 工作温度： | -40°C ~ 125°C |
| 安装类型： | 表面贴装 |
| 封装/外壳： | SOT-23-6 |
| 供应商设备封装： | SOT-23-6 |
| 包装： | 标准包装 |
| 产品目录页面： | 1234 (CN2011-ZH PDF) |
| 其它名称： | ISL28168FHZ-T7ADKR |
13
FN6378.4
July 25, 2011
2. The output current required is higher than the output
stage can deliver. These conditions can result in a shift in
the Input Offset Voltage (VOS) as much as 1V/hr. of
exposure under these conditions.
IN+ and IN- Input Protection
All input terminals have internal ESD protection diodes to both
positive and negative supply rails, limiting the input voltage to
within one diode beyond the supply rails. They also contain
back-to-back diodes across the input terminals (see “Pin
the input differential voltage is expected to exceed 0.5V, an
external series resistor must be used to ensure the input
currents never exceed 5mA (see Figure 41).
Enable/Disable Feature
The ISL28168 offers an EN pin that disables the device
when pulled up to at least 2.0V. In the disabled state (output
in a high impedance state), the part consumes typically 10A
at room temperature. By disabling the part, multiple
ISL28168 parts can be connected together as a MUX. In this
configuration, the outputs are tied together in parallel and a
channel can be selected by the EN pin. The loading effects
of the feedback resistors of the disabled amplifier must be
considered when multiple amplifier outputs are connected
together. Note that feed through from the IN+ to IN- pins
occurs on any Mux Amp disabled channel where the input
differential voltage exceeds 0.5V (e.g., active channel
VOUT = 1V, while disabled channel VIN = GND), so the Mux
implementation is best suited for small signal applications. If
large signals are required, use series IN+ resistors, or large
value RF, to keep the feed-through current low enough to
minimize the impact on the active channel. See “Limitations
details.
To disable the part, the user needs to supply the 1.5A
required to pull the EN pin to the V+ rail. If left open, the EN
pin will pull to the negative rail and the device will be enabled
by default. If the EN function is not required (no need to turn
the part off), as a precaution, it is recommended that the
user tie the EN pin to the V- pin.
Limitations of the Differential Input Protection
If the input differential voltage is expected to exceed 0.5V, an
external current limiting resistor must be used to ensure the
input current never exceeds 5mA. For non inverting unity
gain applications, the current limiting can be via a series IN+
resistor, or via a feedback resistor of appropriate value. For
other gain configurations, the series IN+ resistor is the best
choice, unless the feedback (RF) and gain setting (RG)
resistors are both sufficiently large to limit the input current to
5mA.
Large differential input voltages can arise from several
sources:
1. During open loop (comparator) operation. Used this way,
the IN+ and IN- voltages don’t track, so differentials arise.
2. When the amplifier is disabled but an input signal is still
present. An RL or RG to GND keeps the IN- at GND, while
the varying IN+ signal creates a differential voltage. Mux
Amp applications are similar, except that the active
channel VOUT determines the voltage on the IN- terminal.
3. When the slew rate of the input pulse is considerably
faster than the op amp’s slew rate. If the VOUT can’t keep
up with the IN+ signal, a differential voltage results, and
visible distortion occurs on the input and output signals.
To avoid this issue, keep the input slew rate below
0.1V/s, or use appropriate current limiting resistors.
Large (>2V) differential input voltages can also cause an
increase in disabled ICC.
Using Only One Channel
The ISL28268 is a dual op amp. If the application only
requires one channel, the user must configure the unused
channel to prevent it from oscillating. The unused channel
will oscillate if the input and output pins are floating. This will
result in higher than expected supply currents and possible
noise injection into the channel being used. The proper way
to prevent this oscillation is to short the output to the
negative input and ground the positive input (as shown in
Figure 42).
Proper Layout Maximizes Performance
To achieve the maximum performance of the high input
impedance and low offset voltage, care should be taken in
the circuit board layout. The PC board surface must remain
clean and free of moisture to avoid leakage currents
between adjacent traces. Surface coating of the circuit board
will reduce surface moisture and provide a humidity barrier,
reducing parasitic resistance on the board. When input
leakage current is a concern, the use of guard rings around
the amplifier inputs will further reduce leakage currents.
Figure 43 shows a guard ring example for a unity gain
amplifier that uses the low impedance amplifier output at the
same voltage as the high impedance input to eliminate
surface leakage. The guard ring does not need to be a
specific width, but it should form a continuous loop around
both inputs. For further reduction of leakage currents,
FIGURE 41. INPUT CURRENT LIMITING
-
+
RIN
RL
VIN
VOUT
FIGURE 42. PREVENTING OSCILLATIONS IN UNUSED
CHANNELS
-
+
ISL28168, ISL28268
相关PDF资料 |
PDF描述 |
|---|---|
| LTC6102HDD#TRPBF | IC AMP CURRENT SENSE 8-DFN |
| 1601056-1 | TERM SIAMEZE WIRE TO WIRE |
| AD8012ARMZ-REEL7 | IC OPAMP CF DUAL LP 125MA 8MSOP |
| 5-146138-6 | 08 MODIV VRT SR CE 100/115 |
| MCP603T-E/CH | IC OPAMP CMOS SGL 2.7V SOT23-6 |
相关代理商/技术参数 |
参数描述 |
|---|---|
| ISL28168FHZ-TZA | 制造商:Intersil Corporation 功能描述: |
| ISL28176 | 制造商:INTERSIL 制造商全称:Intersil Corporation 功能描述:Single, Dual and Quad Micropower Single Supply Rail-to-Rail Input and Output (RRIO) Precision Op Amp |
| ISL28176FBZ | 功能描述:IC OPAMP RRIO SGL 120UA 8-SOIC RoHS:是 类别:集成电路 (IC) >> Linear - Amplifiers - Instrumentation 系列:- 标准包装:75 系列:MicroAmplifier™ 放大器类型:通用 电路数:1 输出类型:满摆幅 转换速率:0.03 V/µs 增益带宽积:100kHz -3db带宽:- 电流 - 输入偏压:1pA 电压 - 输入偏移:60µV 电流 - 电源:20µA 电流 - 输出 / 通道:5mA 电压 - 电源，单路/双路(±):2.3 V ~ 5.5 V 工作温度:-40°C ~ 85°C 安装类型:表面贴装 封装/外壳:8-SOIC（0.154"，3.90mm 宽） 供应商设备封装:8-SOIC 包装:管件 |
| ISL28176FBZ-T7 | 功能描述:IC OPAMP RRIO SGL 120UA 8-SOIC RoHS:是 类别:集成电路 (IC) >> Linear - Amplifiers - Instrumentation 系列:- 标准包装:1 系列:- 放大器类型:仪表 电路数:2 输出类型:满摆幅 转换速率:5 V/µs 增益带宽积:- -3db带宽:2MHz 电流 - 输入偏压:0.5pA 电压 - 输入偏移:250µV 电流 - 电源:415µA 电流 - 输出 / 通道:48mA 电压 - 电源，单路/双路(±):2.5 V ~ 5.5 V，±1.25 V ~ 2.75 V 工作温度:-55°C ~ 125°C 安装类型:表面贴装 封装/外壳:14-TSSOP（0.173"，4.40mm 宽） 供应商设备封装:14-TSSOP 包装:剪切带 (CT) 产品目录页面:849 (CN2011-ZH PDF) 其它名称:296-12431-1296-12431-1-NDINA2331AIPWRCT |
| ISL28177FBZ | 制造商:Intersil Corporation 功能描述:ISL28177FBZ PB-FREE 40V GENERAL PURPOSE PRECISION OPERATIONA - Rail/Tube 制造商:Intersil Corporation 功能描述:IC OP AMP GP 600KHZ 8SOIC 制造商:Intersil 功能描述:ISL28177FBZ 40V GEN PURPSE PRCSN OPER |
发布紧急采购，3分钟左右您将得到回复。