参数资料
| 型号： | ISL28190FHZ-T7 |
| 厂商： | Intersil |
| 文件页数： | 3/18页 |
| 文件大小： | 0K |
| 描述： | IC OPAMP R-R SGL ULN SOT23-6 |
| 标准包装： | 1 |
| 放大器类型： | 电压反馈 |
| 电路数： | 1 |
| 输出类型： | 满摆幅 |
| 转换速率： | 50 V/µs |
| -3db带宽： | 170MHz |
| 电流 - 输入偏压： | 10µA |
| 电压 - 输入偏移： | 240µV |
| 电流 - 电源： | 8.5mA |
| 电流 - 输出 / 通道： | 144mA |
| 电压 - 电源，单路/双路(±)： | 3 V ~ 5.5 V，±1.5 V ~ 2.75 V |
| 工作温度： | -40°C ~ 125°C |
| 安装类型： | 表面贴装 |
| 封装/外壳： | SOT-23-6 |
| 供应商设备封装： | SOT-23-6 |
| 包装： | 标准包装 |
| 产品目录页面： | 1234 (CN2011-ZH PDF) |
| 其它名称： | ISL28190FHZ-T7DKR |
ISL28190, ISL28290
11
FN6247.9
January 26, 2012
Applications Information
Product Description
The ISL28190 and ISL28290 are voltage feedback operational
amplifiers designed for communication and imaging applications
requiring low distortion, very low voltage and current noise. Both
parts feature high bandwidth while drawing moderately low supply
current. The ISL28190 and ISL28290 use a classical
voltage-feedback topology, which allows them to be used in a variety
of applications where current-feedback amplifiers are not
appropriate because of restrictions placed upon the feedback
element used with the amplifier.
Enable/Power-Down
The ISL28190 and ISL28290 amplifiers are disabled by applying
a voltage greater than 2V to the EN pin, with respect to the V- pin.
In this condition, the output(s) will be in a high impedance state
and the amplifier(s) current will be reduced to 13A/Amp. By
disabling the part, multiple parts can be connected together as a
MUX. The outputs are tied together in parallel and a channel can
be selected by the EN pin. The EN pin also has an internal
pull-down. If left open, the EN pin will pull to the negative rail and
the device will be enabled by default.
Input Protection
All input terminals have internal ESD protection diodes to both
positive and negative supply rails, limiting the input voltage to
within one diode beyond the supply rails. Both parts have
additional back-to-back diodes across the input terminals
(as shown in Figure 30). In pulse applications where the input Slew
Rate exceeds the Slew Rate of the amplifier, the possibility exists
for the input protection diodes to become forward biased. This can
cause excessive input current and distortion at the outputs. If
overdriving the inputs is necessary, the external input current must
never exceed 5mA. An external series resistor may be used to limit
the current, as shown in Figure 30.
Using Only One Channel
The ISL28290 is a Dual channel op amp. If the application only
requires one channel when using the ISL28290, the user must
configure the unused channel to prevent it from oscillating.
Oscillation can occur if the input and output pins are floating.
This will result in higher than expected supply currents and
possible noise injection into the channel being used. The proper
way to prevent this oscillation is to short the output to the
negative input and ground the positive input (as shown in
Figure 31).
Power Supply Bypassing and Printed Circuit
Board Layout
As with any high frequency device, good printed circuit board
layout is necessary for optimum performance. Low impedance
ground plane construction is essential. Surface mount
components are recommended, but if leaded components are
used, lead lengths should be as short as possible. The power
supply pins must be well bypassed to reduce the risk of
oscillation. The combination of a 4.7F tantalum capacitor in
parallel with a 0.01F capacitor has been shown to work well
when placed at each supply pin.
For good AC performance, parasitic capacitance should be kept
to a minimum, especially at the inverting input. When ground
plane construction is used, it should be removed from the area
near the inverting input to minimize any stray capacitance at that
node. Carbon or Metal-Film resistors are acceptable with the
Metal-Film resistors giving slightly less peaking and bandwidth
because of additional series inductance. Use of sockets,
particularly for the SO package, should be avoided if possible.
Sockets add parasitic inductance and capacitance, which will
result in additional peaking and overshoot.
Current Limiting
The ISL28190 and ISL28290 have no internal current-limiting
circuitry. If the output is shorted, it is possible to exceed the
Absolute Maximum Rating for output current or power
dissipation, potentially resulting in the destruction of the device.
This is why output short circuit current is specified and tested
with RL = 10Ω.
FIGURE 30. LIMITING THE INPUT CURRENT TO LESS THAN 5mA
-
+
R
FIGURE 31. PREVENTING OSCILLATIONS IN UNUSED CHANNELS
-
+
相关PDF资料 |
PDF描述 |
|---|---|
| RMCF0603FT330K | RES 330K OHM 1/10W 1% 0603 SMD |
| TSW-112-14-G-D | CONN HEADER 24POS .100" DL GOLD |
| MMS-125-02-L-SH | CONN RCPT 2MM 25POS SGL HORZ SMD |
| TSW-125-08-T-D | CONN HEADER 50POS .100" DUAL TIN |
| RMCF0603FT4K32 | RES 4.32K OHM 1/10W 1% 0603 SMD |
相关代理商/技术参数 |
参数描述 |
|---|---|
| ISL28190FRUZ-T7 | 功能描述:IC OP AMP R-R SGL ULN 6-UTDFN RoHS:是 类别:集成电路 (IC) >> Linear - Amplifiers - Instrumentation 系列:- 标准包装:100 系列:- 放大器类型:通用 电路数:1 输出类型:- 转换速率:0.2 V/µs 增益带宽积:- -3db带宽:- 电流 - 输入偏压:100pA 电压 - 输入偏移:30µV 电流 - 电源:380µA 电流 - 输出 / 通道:- 电压 - 电源，单路/双路(±):±2 V ~ 18 V 工作温度:0°C ~ 70°C 安装类型:表面贴装 封装/外壳:8-SOIC（0.154"，3.90mm 宽） 供应商设备封装:8-SO 包装:管件 |
| ISL28190FRUZ-TK | 制造商:INTERSIL 制造商全称:Intersil Corporation 功能描述:Single and Dual Ultra-Low Noise, Ultra-Low Distortion, Rail-to-Rail, Op Amp |
| ISL28191 | 制造商:INTERSIL 制造商全称:Intersil Corporation 功能描述:Low Distortion Rail-to-Rail Output, Op Amp |
| ISL28191_08 | 制造商:INTERSIL 制造商全称:Intersil Corporation 功能描述:Single and Dual Single Supply Ultra-Low Noise, Low Distortion Rail-to-Rail Output, Op Amp |
| ISL28191_0808 | 制造商:INTERSIL 制造商全称:Intersil Corporation 功能描述:Low Distortion Rail-to-Rail Output, Op Amp |
发布紧急采购，3分钟左右您将得到回复。