参数资料
| 型号： | ISL28207FUZ-T13 |
| 厂商： | Intersil |
| 文件页数： | 13/31页 |
| 文件大小： | 0K |
| 描述： | IC OPAMP PREC LN DUAL 8-MSOP |
| 产品培训模块： | Solutions for Industrial Control Applications |
| 标准包装： | 2,500 |
| 放大器类型： | 通用 |
| 电路数： | 2 |
| 转换速率： | 0.32 V/µs |
| 增益带宽积： | 1MHz |
| 电流 - 输入偏压： | 15pA |
| 电压 - 输入偏移： | 5µV |
| 电流 - 电源： | 210µA |
| 电流 - 输出 / 通道： | 40mA |
| 电压 - 电源，单路/双路(±)： | 4.5 V ~ 40 V，±2.25 V ~ 20 V |
| 工作温度： | -40°C ~ 125°C |
| 安装类型： | 表面贴装 |
| 封装/外壳： | 8-TSSOP，8-MSOP（0.118"，3.00mm 宽） |
| 供应商设备封装： | 8-MSOP |
| 包装： | 带卷 (TR) |
第1页第2页第3页第4页第5页第6页第7页第8页第9页第10页第11页第12页当前第13页第14页第15页第16页第17页第18页第19页第20页第21页第22页第23页第24页第25页第26页第27页第28页第29页第30页第31页
ISL28107, ISL28207, ISL28407
20
FN6631.7
February 25, 2013
The resistor-ESD diode configuration enables a wide differential
input voltage range equal to the lesser of the Maximum Supply
Voltage in the “Absolute Maximum Ratings” on page 6 (42V), or a
maximum of 0.5V beyond the V+ and V- supply voltage. The
internal protection resistors eliminate the need for external input
current limiting resistors in unity gain connections and other
circuit applications where large voltages or high slew rate signals
are present. Although the amplifier is fully protected, high input
slew rates that exceed the amplifier slew rate (±0.32V/s) may
cause output distortion.
Output Current Limiting
The output current is internally limited to approximately ±40mA
at +25°C and can withstand a short circuit to either rail as long
as the power dissipation limits are not exceeded. This applies to
only one amplifier at a time for the dual op-amp. Continuous
operation under these conditions may degrade long-term
reliability.
Output Phase Reversal
Output phase reversal is a change of polarity in the amplifier
transfer function when the input voltage exceeds the supply
voltage. The ISL28107, ISL28207 and ISL28407 are immune to
output phase reversal, even when the input voltage is 1V beyond
the supplies.
Unused Channels
If the application only requires one channel, the user must
configure the unused channels to prevent them from oscillating.
The unused channels can oscillate if the input and output pins
are floating. This results in higher than expected supply currents
and possible noise injection into the channel being used. The
proper way to prevent this oscillation is to short the output to the
inverting input and ground the positive input, as shown in
Figure 55.
Power Dissipation
It is possible to exceed the +150°C maximum junction
temperatures under certain load and power supply conditions. It
is therefore important to calculate the maximum junction
temperature (TJMAX) for all applications to determine if power
supply voltages, load conditions, or package type need to be
modified to remain in the safe operating area. These parameters
are related using Equation 1:
where:
PDMAXTOTAL is the sum of the maximum power dissipation of
each amplifier in the package (PDMAX)
where:
TMAX = Maximum ambient temperature
θJA = Thermal resistance of the package
PDMAX = Maximum power dissipation of one amplifier
VS = Total supply voltage
IqMAX = Maximum quiescent supply current of one amplifier
VOUTMAX = Maximum output voltage swing of the application
RL = Load resistance
ISL28107, ISL28207, ISL28407 SPICE Model
the net list for the ISL28107, ISL28207 and ISL28407 SPICE
model. The model is a simplified version of the actual device and
simulates important AC and DC parameters. AC parameters
incorporated into the model are: 1/f and flatband noise, Slew
Rate, CMRR, Gain and Phase. The DC parameters are VOS, IOS,
total supply current and output voltage swing. The model uses
typical parameters given in the “Electrical Specifications” table
dominant pole at 0.01Hz. CMRR is set (145dB, fcm = 100Hz). The
input stage models the actual device to present an accurate AC
representation. The model is configured for ambient temperature
of +25°C.
results for the Noise Voltage, Closed Loop Gain vs Frequency,
Closed Loop Gain vs RL, Large Signal Step Response, Open Loop
Gain Phase and Simulated CMRR vs Frequency.
License Statement
The information in this SPICE model is protected under the
United States copyright laws. Intersil Corporation hereby grants
users of this macro-model hereto referred to as “Licensee”, a
nonexclusive, nontransferable licence to use this model as long
as the Licensee abides by the terms of this agreement. Before
using this macro-model, the Licensee should read this license. If
the Licensee does not accept these terms, permission to use the
model is not granted.
The Licensee may not sell, loan, rent, or license the macro-model,
in whole, in part, or in modified form, to anyone outside the
Licensee’s company. The Licensee may modify the macro-model
to suit his/her specific applications, and the Licensee may make
copies of this macro-model for use within their company only.
This macro-model is provided “AS IS, WHERE IS, AND WITH NO
WARRANTY OF ANY KIND EITHER EXPRESSED OR IMPLIED,
INCLUDING BUY NOT LIMITED TO ANY IMPLIED WARRANTIES OF
MERCHANTABILITY AND FITNESS FOR A PARTICULAR PURPOSE.”
In no event will Intersil be liable for special, collateral, incidental, or
consequential damages in connection with or arising out of the
use of this macro-model. Intersil reserves the right to make
changes to the product and the macro-model without prior notice.
FIGURE 55. PREVENTING OSCILLATIONS IN UNUSED CHANNELS
-
+
T
JMAX
T
MAX
θ
JAxPDMAXTOTAL
+
=
(EQ. 1)
PD
MAX
V
S
I
qMAX
V
S
(
- V
OUTMAX )
V
OUTMAX
R
L
----------------------------
×
+
×
=
(EQ. 2)
相关PDF资料 |
PDF描述 |
|---|---|
| M80-8282042 | CONN HDR 2MM SMT W/LATCH 20POS |
| M80-8282022 | CONN HDR 2MM W/LATCH 20POS SMD |
| ISL28207FRTZ-T7 | IC OPAMP PREC 1MHZ DUAL LN 8TDFN |
| 208458160031025 | CONNECTOR RECEPT 160POS STR |
| EL5106IWZ-T7A | IC AMP FGA SGL 300MHZ SOT23-6 |
相关代理商/技术参数 |
参数描述 |
|---|---|
| ISL28207FUZ-T7 | 功能描述:IC OPAMP PREC LN DUAL 8-MSOP RoHS:是 类别:集成电路 (IC) >> Linear - Amplifiers - Instrumentation 系列:- 标准包装:75 系列:MicroAmplifier™ 放大器类型:通用 电路数:1 输出类型:满摆幅 转换速率:0.03 V/µs 增益带宽积:100kHz -3db带宽:- 电流 - 输入偏压:1pA 电压 - 输入偏移:60µV 电流 - 电源:20µA 电流 - 输出 / 通道:5mA 电压 - 电源，单路/双路(±):2.3 V ~ 5.5 V 工作温度:-40°C ~ 85°C 安装类型:表面贴装 封装/外壳:8-SOIC（0.154"，3.90mm 宽） 供应商设备封装:8-SOIC 包装:管件 |
| ISL28207FUZ-T7A | 功能描述:运算放大器 - 运放 ISL28207FUZ DUAL PRE MICROPWR OPERTNL AM RoHS:否 制造商:STMicroelectronics 通道数量:4 共模抑制比（最小值）:63 dB 输入补偿电压:1 mV 输入偏流（最大值）:10 pA 工作电源电压:2.7 V to 5.5 V 安装风格:SMD/SMT 封装 / 箱体:QFN-16 转换速度:0.89 V/us 关闭:No 输出电流:55 mA 最大工作温度:+ 125 C 封装:Reel |
| ISL28207SOICEVAL2Z | 功能描述:EVAL BOARD FOR ISL28207 8SOIC RoHS:是 类别:编程器，开发系统 >> 评估板 - 运算放大器 系列:- 产品培训模块:Lead (SnPb) Finish for COTS Obsolescence Mitigation Program 标准包装:1 系列:- |
| ISL28208 | 制造商:INTERSIL 制造商全称:Intersil Corporation 功能描述:40V Precision Single Supply Rail-Rail Output Low Power Operational Amplifiers |
| ISL28208FBZ | 功能描述:IC OPAMP PREC RR 1.2MHZ DL 8SOIC RoHS:是 类别:集成电路 (IC) >> Linear - Amplifiers - Instrumentation 系列:- 标准包装:1 系列:- 放大器类型:通用 电路数:2 输出类型:满摆幅 转换速率:2.1 V/µs 增益带宽积:3MHz -3db带宽:- 电流 - 输入偏压:1pA 电压 - 输入偏移:2000µV 电流 - 电源:750µA 电流 - 输出 / 通道:16mA 电压 - 电源，单路/双路(±):2.7 V ~ 16 V，±1.35 V ~ 8 V 工作温度:-40°C ~ 125°C 安装类型:表面贴装 封装/外壳:14-SOIC（0.154"，3.90mm 宽） 供应商设备封装:14-SOIC 包装:剪切带 (CT) 其它名称:296-10529-1 |
发布紧急采购，3分钟左右您将得到回复。