参数资料
| 型号： | ISL28233FBZ-T7 |
| 厂商： | Intersil |
| 文件页数： | 6/25页 |
| 文件大小： | 0K |
| 描述： | IC OPAMP CHOPPER RR .4MHZ 8SOIC |
| 产品培训模块： | Patient Monitoring and Diagnostic Equipment Solutions |
| 标准包装： | 1,000 |
| 放大器类型： | 断路器（零漂移） |
| 电路数： | 2 |
| 输出类型： | 满摆幅 |
| 转换速率： | 0.2 V/µs |
| 增益带宽积： | 400kHz |
| 电流 - 输入偏压： | 180pA |
| 电压 - 输入偏移： | 2µV |
| 电流 - 电源： | 18µA |
| 电流 - 输出 / 通道： | 19mA |
| 电压 - 电源，单路/双路(±)： | 1.8 V ~ 6 V，±0.825 V ~ 3 V |
| 工作温度： | -40°C ~ 125°C |
| 安装类型： | 表面贴装 |
| 封装/外壳： | 8-SOIC（0.154"，3.90mm 宽） |
| 供应商设备封装： | 8-SOIC |
| 包装： | 带卷 (TR) |
ISL28233, ISL28433
14
FN7692.3
July 26, 2011
Applications Information
Functional Description
The ISL28233 and ISL28433 use a proprietary
chopper-stabilized technique (see Figure 39) that combines a
400kHz main amplifier with a very high open loop gain (174dB)
chopper amplifier to achieve very low offset voltage and drift
(2V, 0.01V/°C typical) while consuming only 18A of supply
current per channel.
This multi-path amplifier architecture contains a time continuous
main amplifier whose input DC offset is corrected by a parallel-
connected, high gain chopper stabilized DC correction amplifier
operating at 100kHz. From DC to ~5kHz, both amplifiers are active
with DC offset correction and most of the low frequency gain is
provided by the chopper amplifier. A 5kHz crossover filter cuts off
the low frequency amplifier path leaving the main amplifier active
out to the 400kHz gain-bandwidth product of the device.
The key benefits of this architecture for precision applications are
very high open loop gain, very low DC offset, and low 1/f noise.
The noise is virtually flat across the frequency range from a few
millihertz out to 100kHz, except for the narrow noise peak at the
amplifier crossover frequency (5kHz).
Rail-to-rail Input and Output (RRIO)
The RRIO CMOS amplifier uses parallel input PMOS and NMOS that
enable the inputs to swing 100mV beyond either supply rail. The
inverting and non-inverting inputs do not have back-to-back input
clamp diodes and are capable of maintaining high input impedance
at high differential input voltages. This is effective in eliminating
output distortion caused by high slew-rate input signals.
The output stage uses common source connected PMOS and
NMOS devices to achieve rail-to-rail output drive capability with
17mA current limit and the capability to swing to within 20mV of
either rail while driving a 10k
Ω load.
IN+ and IN- Protection
All input terminals have internal ESD protection diodes to both
positive and negative supply rails, limiting the input voltage to
within one diode beyond the supply rails. For applications where
either input is expected to exceed the rails by 0.5V, an external
series resistor must be used to ensure the input currents never
exceed 20mA (see Figure 40).
Layout Guidelines for High Impedance Inputs
To achieve the maximum performance of the high input
impedance and low offset voltage of the ISL28233 and ISL28433
amplifiers, care should be taken in the circuit board layout. The PC
board surface must remain clean and free of moisture to avoid
leakage currents between adjacent traces. Surface coating of the
circuit board will reduce surface moisture and provide a humidity
barrier, reducing parasitic resistance on the board.
High Gain, Precision DC-Coupled Amplifier
The circuit in Figure 41 implements a single-stage DC-coupled
amplifier with an input DC sensitivity of under 100nV that is only
possible using a low VOS amplifier with high open loop gain. High
gain DC amplifiers operating from low voltage supplies are not
practical using typical low offset precision op amps. For example,
a typical precision amplifier in a gain of 10kV/V with a ±100V
VOS and offset drift 0.5V/°C of a low offset op amp would
produce a DC error of >1V with an additional 5mV/°C of
temperature dependent error making it difficult to resolve DC
input voltage changes in the mV range.
The ±6V max VOS and 0.05V/°C max temperature drift of the
ISL28233, ISL28433 produces a temperature stable maximum
DC output error of only ±60mV with a maximum output
temperature drift of 0.5mV/°C. The additional benefit of a very
low 1/f noise corner frequency and some feedback filtering
enables DC voltages and voltage fluctuations well below 100nV
to be easily detected with a simple single stage amplifier.
ISL28233, ISL28433 SPICE Model
shows the net list for the ISL28233, ISL28433 SPICE model. The
model is a simplified version of the actual device and simulates
important parameters such as noise, Slew Rate, Gain and Phase.
The model uses typical parameters from the “Electrical
Specifications Table” on page 5. The poles and zeroes in the
model were determined from the actual open and closed-loop
gain and phase response. This enables the model to present an
accurate AC representation of the actual device. The model is
configured for ambient temperature of +25°C.
results for the Noise Density, Frequency Response vs Close Loop
Gain, Gain vs Frequency vs CL and Large Signal Step Response (4V).
LICENSE STATEMENT
The information in this SPICE model is protected under the
United States copyright laws. Intersil Corporation hereby grants
users of this macro-model hereto referred to as “Licensee”, a
nonexclusive, nontransferable licence to use this model as long
as the Licensee abides by the terms of this agreement. Before
using this macro-model, the Licensee should read this license. If
the Licensee does not accept these terms, permission to use the
model is not granted.
FIGURE 40. INPUT CURRENT LIMITING
-
+
RIN
RL
VIN
VOUT
FIGURE 41. HIGH GAIN, PRECISION DC-COUPLED AMPLIFIER
-
+
100
Ω
RL
VIN
VOUT
1M
Ω
1M
Ω,
100
Ω
-2.5V
+2.5V
ACL = 10kV/V
CF
0.018F
相关PDF资料 |
PDF描述 |
|---|---|
| 160811-8 | CONN UNINS RECPT 10-12AWG 0.250 |
| 218458096008097 | CONNECTOR RECEPT 96POS STR |
| MCP6V03-E/SN | IC OPAMP AUTO-ZERO SNGL CS 8SOIC |
| ISL28227FUZ-T13 | IC OPAMP PREC 10MHZ DUAL 8MSOP |
| ISL28227FRTZ-T13 | IC OPAMP PREC 10MHZ DUAL 8TDFN |
相关代理商/技术参数 |
参数描述 |
|---|---|
| ISL28233FBZ-T7A | 功能描述:IC OPAMP CHOPPER RR .4MHZ 8SOIC RoHS:是 类别:集成电路 (IC) >> Linear - Amplifiers - Instrumentation 系列:- 产品培训模块:Lead (SnPb) Finish for COTS Obsolescence Mitigation Program 标准包装:1 系列:- 放大器类型:电流检测 电路数:1 输出类型:- 转换速率:- 增益带宽积:125kHz -3db带宽:- 电流 - 输入偏压:- 电压 - 输入偏移:100µV 电流 - 电源:1.1µA 电流 - 输出 / 通道:- 电压 - 电源，单路/双路(±):- 工作温度:-40°C ~ 85°C 安装类型:表面贴装 封装/外壳:4-WFBGA，CSPBGA 供应商设备封装:4-UCSP（2x2） 包装:剪切带 (CT) 其它名称:MAX9634WERS+TCT |
| ISL28233FRTZ-T7 | 制造商:INTERSIL 制造商全称:Intersil Corporation 功能描述:Single, Dual, and Quad Micropower, Zero-Drift, RRIO Operational Amplifiers |
| ISL28233FRZ | 功能描述:IC OPAMP CHOPPER RR .4MHZ 8DFN RoHS:是 类别:集成电路 (IC) >> Linear - Amplifiers - Instrumentation 系列:- 标准包装:75 系列:MicroAmplifier™ 放大器类型:通用 电路数:1 输出类型:满摆幅 转换速率:0.03 V/µs 增益带宽积:100kHz -3db带宽:- 电流 - 输入偏压:1pA 电压 - 输入偏移:60µV 电流 - 电源:20µA 电流 - 输出 / 通道:5mA 电压 - 电源，单路/双路(±):2.3 V ~ 5.5 V 工作温度:-40°C ~ 85°C 安装类型:表面贴装 封装/外壳:8-SOIC（0.154"，3.90mm 宽） 供应商设备封装:8-SOIC 包装:管件 |
| ISL28233FRZ-T13 | 功能描述:IC OPAMP CHOPPER RR .4MHZ 8DFN RoHS:是 类别:集成电路 (IC) >> Linear - Amplifiers - Instrumentation 系列:- 标准包装:75 系列:MicroAmplifier™ 放大器类型:通用 电路数:1 输出类型:满摆幅 转换速率:0.03 V/µs 增益带宽积:100kHz -3db带宽:- 电流 - 输入偏压:1pA 电压 - 输入偏移:60µV 电流 - 电源:20µA 电流 - 输出 / 通道:5mA 电压 - 电源，单路/双路(±):2.3 V ~ 5.5 V 工作温度:-40°C ~ 85°C 安装类型:表面贴装 封装/外壳:8-SOIC（0.154"，3.90mm 宽） 供应商设备封装:8-SOIC 包装:管件 |
| ISL28233FRZ-T7 | 功能描述:IC OPAMP CHOPPER RR .4MHZ 8DFN RoHS:是 类别:集成电路 (IC) >> Linear - Amplifiers - Instrumentation 系列:- 标准包装:75 系列:MicroAmplifier™ 放大器类型:通用 电路数:1 输出类型:满摆幅 转换速率:0.03 V/µs 增益带宽积:100kHz -3db带宽:- 电流 - 输入偏压:1pA 电压 - 输入偏移:60µV 电流 - 电源:20µA 电流 - 输出 / 通道:5mA 电压 - 电源，单路/双路(±):2.3 V ~ 5.5 V 工作温度:-40°C ~ 85°C 安装类型:表面贴装 封装/外壳:8-SOIC（0.154"，3.90mm 宽） 供应商设备封装:8-SOIC 包装:管件 |
发布紧急采购，3分钟左右您将得到回复。