参数资料
型号: ISL28236FBZ-T7
厂商: Intersil
文件页数: 2/13页
文件大小: 0K
描述: IC OPAMP RRIO DUAL 5MHZ 8-SOIC
标准包装: 1,000
放大器类型: 通用
电路数: 2
输出类型: 满摆幅
转换速率: 1.8 V/µs
增益带宽积: 5MHz
电流 - 输入偏压: 6nA
电压 - 输入偏移: 20µV
电流 - 电源: 2mA
电流 - 输出 / 通道: 70mA
电压 - 电源,单路/双路(±): 2.4 V ~ 5.5 V,±1.2 V ~ 2.75 V
工作温度: -40°C ~ 125°C
安装类型: 表面贴装
封装/外壳: 8-SOIC(0.154",3.90mm 宽)
供应商设备封装: 8-SOIC
包装: 带卷 (TR)
10
FN6921.0
June 18, 2009
Applications Information
Introduction
The ISL28236 is a dual channel Bi-CMOS rail-to-rail input,
output (RRIO) micropower precision operational amplifier.
The part is designed to operate from single supply (2.4V to
5.5V) or dual supply (±1.2V to ±2.75V). The ISL28236 has
an input common mode range that extends 0.25V above the
positive rail and down to the negative supply rail. The output
operation can swing within about 3mV of the supply rails with
a 100k
Ω load.
Rail-to-Rail Input
Many rail-to-rail input stages use two differential input pairs,
a long-tail PNP (or PFET) and an NPN (or NFET). Severe
penalties have to be paid for this circuit topology. As the
input signal moves from one supply rail to another, the
operational amplifier switches from one input pair to the
other. Thus causing drastic changes in input offset voltage
and an undesired change in magnitude and polarity of input
offset current.
The ISL28236 solves this problem using an internal
charge-pump to provide a voltage boost to the V+ supply rail
driving the input differential pair. This results in extending the
input common voltage rails to 0.25V beyond the V+ positive
rail. The input offset voltage exhibits a smooth behavior
throughout the extended common-mode input range. The
input bias current versus the common-mode voltage range
gives an undistorted behavior from the negative rail to 0.25V
higher than the positive rail.
Power Supply Decoupling
The internal charge pump operates at approximately 27MHz
and oscillator ripple doesn’t show up in the 5MHz bandwidth
of the amplifier. Good power supply decoupling with 0.01F
capacitors at each device power supply pin, is the most
effective way to reduce oscillator ripple at the amplifier
output. Figure 36 shows the electrical connection of these
capacitors using split power supplies. For single supply
operation with V- tied to a ground plane, only a single 0.01F
capacitor from V+ is needed. When multiple ISL28236
op amps are used on a single PC board, each op amp will
require a 0.01F decoupling capacitor at each supply pin
Rail-to-Rail Output
The rail-rail output stage uses CMOS devices that typically
swing to within 3mV of the supply rails with a 100k
Ω load.
The NMOS sinks current to swing the output in the negative
direction. The PMOS sources current to swing the output in the
positive direction.
Pin Descriptions
ISL28236
(8 Ld SOIC)
(8 Ld MSOP)
PIN NAME
FUNCTION
EQUIVALENT CIRCUIT
2 (A)
6 (B)
IN-
IN-_A
IN-_B
inverting input
Circuit 1
3 (A)
5 (B)
IN+
IN+_A
IN+_B
Non-inverting input
See Circuit 1
4
V-
Negative supply
Circuit 2
1 (A)
7 (B)
OUT
OUT_A
OUT_B
Output
Circuit 3
8
V+
Positive supply
See Circuit 2
IN+
IN-
V+
V-
V+
V-
CAPACITIVELY
COUPLED
ESD CLAMP
V+
V-
OUT
ISL28236
相关PDF资料
PDF描述
ISL28266FUZ IC OPAMP RRIO CURRENT 39UA 8MSOP
ISL28268FUZ-T7 IC OP AMP DUAL RRIO 34UA 8-MSOP
ISL28272FAZ-T7 IC INSTR AMP RRIO DUAL 16-QSOP
ISL28290FBZ-T7 IC OP AMP DUAL RRIO 8-SOIC
ISL28291FBZ-T7 IC OP AMP DUAL RRIO 8-SOIC
相关代理商/技术参数
参数描述
ISL28236FUZ 制造商:INTERSIL 制造商全称:Intersil Corporation 功能描述:5MHz, Dual Precision Rail-to-Rail Input-Output (RRIO) Op Amp
ISL28236FUZ-T7 制造商:INTERSIL 制造商全称:Intersil Corporation 功能描述:5MHz, Dual Precision Rail-to-Rail Input-Output (RRIO) Op Amp
ISL28236SOICEVAL1Z 功能描述:EVAL BOARD 1 FOR ISL28236 SOIC RoHS:是 类别:编程器,开发系统 >> 评估板 - 运算放大器 系列:- 产品培训模块:Lead (SnPb) Finish for COTS Obsolescence Mitigation Program 标准包装:1 系列:-
ISL28238 制造商:INTERSIL 制造商全称:Intersil Corporation 功能描述:4.5MHz, Single and Dual Precision Rail-to-Rail Input-Output (RRIO) Op Amps with Very Low Input Bias Current
ISL28238FBZ 制造商:INTERSIL 制造商全称:Intersil Corporation 功能描述:4.5MHz, Single and Dual Precision Rail-to-Rail Input-Output (RRIO) Op Amps with Very Low Input Bias Current