- 您现在的位置：买卖IC网 > PDF目录381957 > ISL28271 (Intersil Corporation) Dual Micropower, Single Supply, Rail-to-Rail Input and Output (RRIO) Instrumentation Amplifier(双微功率,单电源,轨对轨输入/输出(RRIO)测量放大器) PDF资料下载
参数资料
| 型号： | ISL28271 |
| 厂商： | Intersil Corporation |
| 元件分类： | 运动控制电子 |
| 英文描述： | Dual Micropower, Single Supply, Rail-to-Rail Input and Output (RRIO) Instrumentation Amplifier(双微功率,单电源,轨对轨输入/输出(RRIO)测量放大器) |
| 中文描述： | 双微功耗，单电源，轨到轨输入和输出（RRIO）仪表放大器（双微功率，单电源，轨对轨输入/输出（RRIO）测量放大器） |
| 文件页数： | 11/14页 |
| 文件大小： | 688K |
| 代理商： | ISL28271 |
11
FN6390.2
August 17, 2007
Application Information
Product Description
The ISL28271 and ISL28272 are dual channel micropower
instrumentation amplifiers (in-amps) which deliver rail-to-rail
input amplification and rail-to-rail output swing. The in-amps
also deliver excellent DC and AC specifications while
consuming only about 120μA for both channels. Because
the independent pair of feedback terminals set the gain and
adjust the output zero level, the ISL28271 and ISL28272
achieve high CMRR regardless of the tolerance of the gain
setting resistors. The ISL28271 is internally compensated for
a minimum gain of 10. The ISL28272 is internally
compensated for a minimum gain of 100.
EN pins are available to independently enable or disable a
channel. When all channels are off, current consumption is
down to typically 4μA.
Input Protection
All input terminals and feedback terminals have internal ESD
protection diodes to both positive and negative supply rails,
limiting the input voltage to within one diode beyond the
supply rails. Input signals originating from low impedance
sources should have current limiting resistors in series with
the IN+ and IN- pins to prevent damaging currents during
power supply sequencing and other transient conditions.
The ISL28272 has additional back-to-back diodes across the
input terminals and also across the feedback terminals. If
overdriving the inputs is necessary, the external input current
must never exceed 5mA. External series resistors may be
used as an external protection to limit excessive external
voltage and current from damaging the inputs. On the other
hand, the ISL28271 has no clamps to limit the differential
voltage on the input terminals allowing higher differential
input voltages at lower gain applications. It is recommended
however, that the terminals of the ISL28271 are not
overdriven beyond 1V to avoid offset drift.
Input Stage and Input Voltage Range
The input terminals (IN+ and IN-) of the in-amps are a single
differential pair of CMOS devices aided by an Input Range
Enhancement Circuit, IREC, to increase the headroom of
operation of the common-mode input voltage. The feedback
terminals (FB+ and FB-) also have a similar topology. As a
result, the input common-mode voltage range is rail-to-rail
regardless of the feedback terminal settings and regardless
of the gain settings. They are able to handle input voltages
that are at or slightly beyond the supply and ground sensing
making these in-amps well suited for single 5V down to 2.4V
supply systems.
The IREC enables rail-to-rail input amplification without the
problems usually associated with the dual differential stage
topology. The IREC ensures that there are no drastic
changes in offset voltage over the entire range of the input.
See Input Offset Voltage vs Common-Mode Input Voltage in
performance charts. IREC also cures the abrupt change and
even reverse polarity of the input bias current over the whole
range of input.
Output Stage and Output Voltage Range
A Class AB common-source output stage drives the output.
The pair of complementary MOSFET devices drive the
output VOUT to within a few millivolts of the supply rails. At a
100k
Ω
load, the PMOS sources current and pulls the output
up to 4mV below the positive supply. The NMOS sinks
current and pulls the output down to 4mV above the negative
supply, or ground in the case of a single supply operation.
The current sinking and sourcing capability are internally
limited to 31mA. When disabled, the outputs are in a high
impedance state.
Gain Setting
VIN, the potential difference across IN+ and IN-, is replicated
(less the input offset voltage) across FB+ and FB-. The
function of the in-amp is to maintain the differential voltage
across FB- and FB+ equal to IN+ and IN-; (FB- - FB+) =
(IN+ - IN-). Consequently, the transfer function can be
derived. The in-amp gain is set by two external resistors, the
feedback resistor R
F
, and the gain resistor R
G
.
In Figure 37, the FB+ pin and one end of resistor RG are
connected to GND. With this configuration, Equation 1 is
only true for a positive swing in VIN; negative input swings
will be ignored because the output will be at ground.
Reference Connection
Unlike a three op amp in-amp realization, a finite series
resistance seen at the REF terminal does not degrade the
high CMRR performance eliminating the need for an
additional external buffer amplifier. Figure 38 uses the FB+
pin to provide a high impedance REF terminal.
+
-
+
-
IN+
IN-
FB+
FB-
V+
V-
ISL28271
ISL28272
EN
2.4V TO 5.5V
RF
RG
VOUT
EN
VCM
IN+
IN-
FIGURE 37. GAIN IS SET BY TWO EXTERNAL RESISTORS,
R
F
AND R
G
VOUT
1
R
F
R
G
--------
+
VIN
=
VIN
IN+
IN-
–
=
(EQ. 1)
ISL28271, ISL28272
相关PDF资料 |
PDF描述 |
|---|---|
| ISL28272 | Dual Micropower, Single Supply, Rail-to-Rail Input and Output (RRIO) Instrumentation Amplifier(双微功率,单电源,轨对轨输入/输出(RRIO)测量放大器) |
| ISL28278 | Dual and Quad Micropower Single Supply Rail-to-Rail Input and Output (RRIO) Op-Amp(双/四通道，微功率，单电源，轨对轨输入/输出(RRIO)运放) |
| ISL28478 | Dual and Quad Micropower Single Supply Rail-to-Rail Input and Output (RRIO) Op-Amp(双/四通道，微功率，单电源，轨对轨输入/输出(RRIO)运放) |
| ISL28286 | Dual and Quad Micropower Single Supply Rail-to-Rail Input and Output (RRIO) Precision Op Amp(双/四通道，微功率，单电源，轨对轨输入/输出(RRIO)精密运放) |
| ISL28486 | Dual and Quad Micropower Single Supply Rail-to-Rail Input and Output (RRIO) Precision Op Amp(双/四通道，微功率，单电源，轨对轨输入/输出(RRIO)精密运放) |
相关代理商/技术参数 |
参数描述 |
|---|---|
| ISL28271_07 | 制造商:INTERSIL 制造商全称:Intersil Corporation 功能描述:Dual Micropower, Single Supply, Rail-to- Rail Input and Output (RRIO) Instrumentation Amplifier |
| ISL28271FAZ | 功能描述:IC INSTR AMP RRIO SGL 16-QSOP RoHS:是 类别:集成电路 (IC) >> Linear - Amplifiers - Instrumentation 系列:- 标准包装:75 系列:MicroAmplifier™ 放大器类型:通用 电路数:1 输出类型:满摆幅 转换速率:0.03 V/µs 增益带宽积:100kHz -3db带宽:- 电流 - 输入偏压:1pA 电压 - 输入偏移:60µV 电流 - 电源:20µA 电流 - 输出 / 通道:5mA 电压 - 电源，单路/双路(±):2.3 V ~ 5.5 V 工作温度:-40°C ~ 85°C 安装类型:表面贴装 封装/外壳:8-SOIC（0.154"，3.90mm 宽） 供应商设备封装:8-SOIC 包装:管件 |
| ISL28271FAZ-T7 | 功能描述:IC INSTR AMP RRIO DUAL 16-QSOP RoHS:是 类别:集成电路 (IC) >> Linear - Amplifiers - Instrumentation 系列:- 产品培训模块:Lead (SnPb) Finish for COTS Obsolescence Mitigation Program 标准包装:1 系列:- 放大器类型:电流检测 电路数:1 输出类型:- 转换速率:- 增益带宽积:125kHz -3db带宽:- 电流 - 输入偏压:- 电压 - 输入偏移:100µV 电流 - 电源:1.1µA 电流 - 输出 / 通道:- 电压 - 电源，单路/双路(±):- 工作温度:-40°C ~ 85°C 安装类型:表面贴装 封装/外壳:4-WFBGA，CSPBGA 供应商设备封装:4-UCSP（2x2） 包装:剪切带 (CT) 其它名称:MAX9634WERS+TCT |
| ISL28271INEVAL1Z | 功能描述:EVALUATION BOARD FOR ISL28271 RoHS:是 类别:编程器，开发系统 >> 评估板 - 运算放大器 系列:- 产品培训模块:Lead (SnPb) Finish for COTS Obsolescence Mitigation Program 标准包装:1 系列:- |
| ISL28272 | 制造商:INTERSIL 制造商全称:Intersil Corporation 功能描述:Dual Micropower, Single Supply, Rail-to- Rail Input and Output (RRIO) Instrumentation Amplifier |
发布紧急采购，3分钟左右您将得到回复。