参数资料
| 型号： | ISL28417FBBZ-T7A |
| 厂商： | Intersil |
| 文件页数： | 13/34页 |
| 文件大小： | 0K |
| 描述： | IC OPAMP 1.5MHZ QUAD LP 14SOIC |
| 标准包装： | 1 |
| 放大器类型： | 通用 |
| 电路数： | 4 |
| 转换速率： | 0.5 V/µs |
| 增益带宽积： | 1.5MHz |
| 电流 - 输入偏压： | 80pA |
| 电压 - 输入偏移： | 10µV |
| 电流 - 电源： | 440µA |
| 电流 - 输出 / 通道： | 43mA |
| 电压 - 电源，单路/双路(±)： | 4.5 V ~ 40 V，±2.25 V ~ 20 V |
| 工作温度： | -40°C ~ 125°C |
| 安装类型： | 表面贴装 |
| 封装/外壳： | 14-SOIC（0.154"，3.90mm 宽） |
| 供应商设备封装： | 14-SOIC |
| 包装： | 标准包装 |
| 其它名称： | ISL28417FBBZ-T7ADKR |
第1页第2页第3页第4页第5页第6页第7页第8页第9页第10页第11页第12页当前第13页第14页第15页第16页第17页第18页第19页第20页第21页第22页第23页第24页第25页第26页第27页第28页第29页第30页第31页第32页第33页第34页
ISL28117, ISL28217, ISL28417
20
November 30, 2012
FN6632.10
In applications where one or both amplifier input terminals are at
risk of exposure to high voltages beyond the power supply rails,
current limiting resistors may be needed at the input terminal to
limit the current through the power supply ESD diodes to
20mA max.
Output Current Limiting
The output current is internally limited to approximately ±45mA
at +25°C and can withstand a short circuit to either rail as long
as the power dissipation limits are not exceeded. This applies to
only 1 amplifier at a time for the dual op amp. Continuous
operation under these conditions may degrade long term
temperature.
Output Phase Reversal
Output phase reversal is a change of polarity in the amplifier
transfer function when the input voltage exceeds the supply
voltage. The ISL28117, ISL28217 and ISL28417 are immune to
output phase reversal, even when the input voltage is 1V beyond
the supplies.
Unused Channels
The ISL28217 is a dual op-amp. If the application only requires
one channel, the user must configure the unused channel to
prevent it from oscillating. The unused channel oscillates if the
input and output pins are floating. This results in higher than
expected supply currents and possible noise injection into the
channel being used. The proper way to prevent this oscillation is
to short the output to the inverting input and ground the positive
input, as shown in Figure 55.
Power Dissipation
It is possible to exceed the +150°C maximum junction
temperatures under certain load and power supply conditions. It
is therefore important to calculate the maximum junction
temperature (TJMAX) for all applications to determine if power
supply voltages, load conditions, or package type need to be
modified to remain in the safe operating area. These parameters
are related using Equation 1:
where:
PDMAXTOTAL is the sum of the maximum power dissipation of
each amplifier in the package (PDMAX)
where:
TMAX = Maximum ambient temperature
θJA = Thermal resistance of the package
PDMAX = Maximum power dissipation of 1 amplifier
VS = Total supply voltage
IqMAX = Maximum quiescent supply current of 1 amplifier
VOUTMAX = Maximum output voltage swing of the application
ISL28117, ISL28217 and ISL28417 SPICE
Model
shows the net list for the ISL28117, ISL28217 and ISL28417
SPICE model for a Grade “B” part. The model is a simplified
version of the actual device and simulates important AC and DC
parameters. AC parameters incorporated into the model are: 1/f
and flatband noise, Slew Rate, CMRR, Gain and Phase. The DC
parameters are VOS, IOS, total supply current and output voltage
swing. The model uses typical parameters given in the “Electrical
Specifications” Table beginning on page 6. The AVOL is adjusted
for 155dB with the dominate pole at 0.02Hz. The CMRR is set
(210dB, fcm = 10Hz). The input stage models the actual device to
present an accurate AC representation. The model is configured
for ambient temperature of +25°C.
results for the Noise Voltage, Closed Loop Gain vs Frequency,
Closed Loop Gain vs RL, Large Signal Step Response, Open Loop
Gain Phase and Simulated CMRR vs Frequency.
FIGURE 55. PREVENTING OSCILLATIONS IN UNUSED CHANNELS
-
+
TJMAX
TMAX θJAxPDMAXTOTAL
+
=
(EQ. 1)
PDMAX
VS IqMAX VS
(
- VOUTMAX)
VOUTMAX
RL
------------------------
×
+
×
=
(EQ. 2)
相关PDF资料 |
PDF描述 |
|---|---|
| 929842-01-07-30 | CONN RCPT 14POS DL STR .1" GO |
| 929842-01-05-10 | CONN RCPT 10POS DL STR .1" GO |
| 929841-01-16-30 | CONN RCPT 16POS STR .100" GOL |
| RC0805FR-07115KL | RES 115K OHM 1/8W 1% 0805 SMD |
| TSW-132-07-S-S | CONN HEADER 32POS .100" SGL GOLD |
相关代理商/技术参数 |
参数描述 |
|---|---|
| ISL28417FBZ | 功能描述:IC OPAMP PREC 1.5MHZ LP 14SOIC RoHS:是 类别:集成电路 (IC) >> Linear - Amplifiers - Instrumentation 系列:- 标准包装:75 系列:MicroAmplifier™ 放大器类型:通用 电路数:1 输出类型:满摆幅 转换速率:0.03 V/µs 增益带宽积:100kHz -3db带宽:- 电流 - 输入偏压:1pA 电压 - 输入偏移:60µV 电流 - 电源:20µA 电流 - 输出 / 通道:5mA 电压 - 电源，单路/双路(±):2.3 V ~ 5.5 V 工作温度:-40°C ~ 85°C 安装类型:表面贴装 封装/外壳:8-SOIC（0.154"，3.90mm 宽） 供应商设备封装:8-SOIC 包装:管件 |
| ISL28417FBZ-T13 | 功能描述:IC OPAMP PREC 1.5MHZ LP 14SOIC RoHS:是 类别:集成电路 (IC) >> Linear - Amplifiers - Instrumentation 系列:- 标准包装:75 系列:MicroAmplifier™ 放大器类型:通用 电路数:1 输出类型:满摆幅 转换速率:0.03 V/µs 增益带宽积:100kHz -3db带宽:- 电流 - 输入偏压:1pA 电压 - 输入偏移:60µV 电流 - 电源:20µA 电流 - 输出 / 通道:5mA 电压 - 电源，单路/双路(±):2.3 V ~ 5.5 V 工作温度:-40°C ~ 85°C 安装类型:表面贴装 封装/外壳:8-SOIC（0.154"，3.90mm 宽） 供应商设备封装:8-SOIC 包装:管件 |
| ISL28417FBZ-T7 | 功能描述:IC OPAMP PREC 1.5MHZ LP 14SOIC RoHS:是 类别:集成电路 (IC) >> Linear - Amplifiers - Instrumentation 系列:- 标准包装:75 系列:MicroAmplifier™ 放大器类型:通用 电路数:1 输出类型:满摆幅 转换速率:0.03 V/µs 增益带宽积:100kHz -3db带宽:- 电流 - 输入偏压:1pA 电压 - 输入偏移:60µV 电流 - 电源:20µA 电流 - 输出 / 通道:5mA 电压 - 电源，单路/双路(±):2.3 V ~ 5.5 V 工作温度:-40°C ~ 85°C 安装类型:表面贴装 封装/外壳:8-SOIC（0.154"，3.90mm 宽） 供应商设备封装:8-SOIC 包装:管件 |
| ISL28417FBZ-T7A | 功能描述:运算放大器 - 运放 ISL28417FBZ QUAD 40V PREC LW PWR OPERTNL RoHS:否 制造商:STMicroelectronics 通道数量:4 共模抑制比（最小值）:63 dB 输入补偿电压:1 mV 输入偏流（最大值）:10 pA 工作电源电压:2.7 V to 5.5 V 安装风格:SMD/SMT 封装 / 箱体:QFN-16 转换速度:0.89 V/us 关闭:No 输出电流:55 mA 最大工作温度:+ 125 C 封装:Reel |
| ISL28417FRZ | 制造商:INTERSIL 制造商全称:Intersil Corporation 功能描述:40V Precision Low Power Operational Amplifiers |
发布紧急采购，3分钟左右您将得到回复。