参数资料
| 型号： | ISL28470FAZ |
| 厂商： | Intersil |
| 文件页数： | 6/18页 |
| 文件大小： | 0K |
| 描述： | IC OP AMP QUAD R-R MCPWR 28-QSOP |
| 标准包装： | 48 |
| 放大器类型： | 仪表 |
| 电路数： | 4 |
| 输出类型： | 满摆幅 |
| 转换速率： | 0.5 V/µs |
| -3db带宽： | 240kHz |
| 电流 - 输入偏压： | 250pA |
| 电压 - 输入偏移： | 35µV |
| 电流 - 电源： | 260µA |
| 电流 - 输出 / 通道： | 29mA |
| 电压 - 电源，单路/双路(±)： | 2.4 V ~ 5.5 V，±1.2 V ~ 2.75 V |
| 工作温度： | -40°C ~ 125°C |
| 安装类型： | 表面贴装 |
| 封装/外壳： | 28-SSOP（0.154"，3.90mm 宽） |
| 供应商设备封装： | 28-QSOP |
| 包装： | 管件 |
| 产品目录页面： | 1235 (CN2011-ZH PDF) |
14
FN6260.6
October 21, 2009
Application Information
Product Description
The ISL28270 and ISL28273 are dual channel micro-power
instrumentation amplifiers (in-amps) and the ISL28470 is a
quad channel which deliver rail-to-rail input amplification and
rail-to-rail output swing. The in-amps also deliver excellent
DC and AC specifications while consuming only about 60A
per channel. Because the independent pair of feedback
terminals set the gain and adjust the output zero level, the
ISL28270, ISL28273 and ISL28470 achieve high CMRR
regardless of the tolerance of the gain setting resistors. The
ISL28270 and ISL28470 are internally compensated for a
minimum gain of 100. The ISL28273 is internally
compensated for a minimum gain of 10.
Input Protection
All input terminals and feedback terminals have internal ESD
protection diodes to both positive and negative supply rails,
limiting the input voltage to within one diode beyond the
supply rails. Input signals originating from low impedance
sources should have current limiting resistors in series with
the IN+ and IN- pins to prevent damaging currents during
power supply sequencing and other transient conditions.
The ISL28270 and ISL28470 have additional back-to-back
diodes across the input terminals and also across the
feedback terminals. If overdriving the inputs is necessary,
the external input current must never exceed 5mA. External
series resistors may be used as an external protection to
limit excessive external voltage and current from damaging
the inputs. On the other hand, the ISL28273 has no clamps
to limit the differential voltage on the input terminals allowing
higher differential input voltages at lower gain applications. It
is recommended, however, that the terminals of the
ISL28273 are not overdriven beyond 1V to avoid offset drift.
Input Stage and Input Voltage Range
The input terminals (IN+ and IN-) of the in-amps are a single
differential pair of bipolar PNP devices aided by an Input Range
Enhancement Circuit (IREC), to increase the headroom of
operation of the common-mode input voltage. The feedback
terminals (FB+ and FB-) also have a similar topology. As a
result, the input common-mode voltage range is rail-to-rail
regardless of the feedback terminal settings and regardless of
the gain settings. They are able to handle input voltages that
are at or slightly beyond the supply and close to ground making
these in-amps well suited for single 5V down to 2.4V supply
systems. There is no need to bias the common-mode input to
achieve symmetrical input voltage. It is recommended however
that the common-mode input be biased at least 10mV above
the negative supply rail to achieve top performance. See “Input
The IREC enables rail-to-rail input amplification without the
problems usually associated with the dual differential stage
topology. The IREC ensures that there are no drastic
changes in offset voltage over the entire range of the input.
See Input Offset Voltage vs Common-Mode Input Voltage on
page 8. IREC also cures the abrupt change and even
reverse polarity of the input bias current over the whole
16
7
V+
Circuit 4
Positive Supply terminal shared by all channels.
8
22
V-
Circuit 4
Negative Supply terminal shared by all channels. Grounded for single
supply operation.
1, 9
14,15
NC
No Connect, pins can be left floating or grounded.
7, 10
DNC
Do Not Connect: Internal connection- Must be left floating.
Pin Descriptions (Continued)
ISL28270
16 Ld QSOP
ISL28273
16 Ld QSOP
ISL28470
28 Ld QSOP
PIN NAME
EQUIVALENT
CIRCUIT
PIN FUNCTION
IN-
V+
V-
LOGIC
PIN
V+
V-
V+
V-
OUT
CIRCUIT 3
CIRCUIT 1A
CIRCUIT 2
V+
V-
CAPACITIVELY
COUPLED
ESD CLAMP
CIRCUIT 4
V+
V-
CIRCUIT 1B
FB-
IN-
FB-
IN+
FB+
IN+
FB+
ISL28270, ISL28273, ISL28470
相关PDF资料 |
PDF描述 |
|---|---|
| TA45-ABTWF150U4 | CIRCUIT BRKR ROCKER 15A 2POLE QC |
| 0459858341 | CONN HEADER 8PWR 24SGL 3.18MM |
| 6-1879208-9 | RES 6.80K OHM 1/16W 0.1% 0402 |
| 0459858243 | CONN HEADER 8PWR 24SGL 1.57MM |
| 0459858242 | CONN HEADER 8PWR 24SGL 2.36MM |
相关代理商/技术参数 |
参数描述 |
|---|---|
| ISL28470FAZ-T7 | 功能描述:IC OPAMP QUAD RRIO MCPWR 28-QSOP RoHS:是 类别:集成电路 (IC) >> Linear - Amplifiers - Instrumentation 系列:- 其它有关文件:Automotive Product Guide 产品培训模块:Lead (SnPb) Finish for COTS Obsolescence Mitigation Program 标准包装:1 系列:- 放大器类型:通用 电路数:1 输出类型:满摆幅 转换速率:3 V/µs 增益带宽积:10MHz -3db带宽:- 电流 - 输入偏压:1pA 电压 - 输入偏移:70µV 电流 - 电源:2.5mA 电流 - 输出 / 通道:48mA 电压 - 电源，单路/双路(±):2.7 V ~ 5.5 V，±1.35 V ~ 2.75 V 工作温度:-40°C ~ 125°C 安装类型:表面贴装 封装/外壳:SOT-23-6 供应商设备封装:SOT-6 包装:Digi-Reel® 其它名称:MAX4475AUT#TG16DKR |
| ISL28470FAZ-T7A | 功能描述:IC OPAMP INST RRIO QUAD 28QSOP RoHS:是 类别:集成电路 (IC) >> Linear - Amplifiers - Instrumentation 系列:- 其它有关文件:Automotive Product Guide 产品培训模块:Lead (SnPb) Finish for COTS Obsolescence Mitigation Program 标准包装:1 系列:- 放大器类型:通用 电路数:1 输出类型:满摆幅 转换速率:3 V/µs 增益带宽积:10MHz -3db带宽:- 电流 - 输入偏压:1pA 电压 - 输入偏移:70µV 电流 - 电源:2.5mA 电流 - 输出 / 通道:48mA 电压 - 电源，单路/双路(±):2.7 V ~ 5.5 V，±1.35 V ~ 2.75 V 工作温度:-40°C ~ 125°C 安装类型:表面贴装 封装/外壳:SOT-23-6 供应商设备封装:SOT-6 包装:Digi-Reel® 其它名称:MAX4475AUT#TG16DKR |
| ISL28474 | 制造商:INTERSIL 制造商全称:Intersil Corporation 功能描述:Micropower, Single Supply, Rail-to-Rail Input-Output Instrumentation Amplifier and Precision Operational Amplifier |
| ISL28474EVAL1Z | 功能描述:EVALUATION BOARD FOR ISL28474 RoHS:是 类别:编程器，开发系统 >> 评估板 - 运算放大器 系列:- 产品培训模块:Lead (SnPb) Finish for COTS Obsolescence Mitigation Program 标准包装:1 系列:- |
| ISL28474FAZ | 功能描述:IC OPAMP QUAD RRIO MCPWR 24-QSOP RoHS:是 类别:集成电路 (IC) >> Linear - Amplifiers - Instrumentation 系列:- 其它有关文件:Automotive Product Guide 产品培训模块:Lead (SnPb) Finish for COTS Obsolescence Mitigation Program 标准包装:1 系列:- 放大器类型:通用 电路数:1 输出类型:满摆幅 转换速率:3 V/µs 增益带宽积:10MHz -3db带宽:- 电流 - 输入偏压:1pA 电压 - 输入偏移:70µV 电流 - 电源:2.5mA 电流 - 输出 / 通道:48mA 电压 - 电源，单路/双路(±):2.7 V ~ 5.5 V，±1.35 V ~ 2.75 V 工作温度:-40°C ~ 125°C 安装类型:表面贴装 封装/外壳:SOT-23-6 供应商设备封装:SOT-6 包装:Digi-Reel® 其它名称:MAX4475AUT#TG16DKR |
发布紧急采购，3分钟左右您将得到回复。