- 您现在的位置：买卖IC网 > PDF目录383129 > ISL29002 (Intersil Corporation) Light-to-Digital I2C Sensor(光电I2C传感器) PDF资料下载
参数资料
| 型号： | ISL29002 |
| 厂商： | Intersil Corporation |
| 英文描述： | Light-to-Digital I2C Sensor(光电I2C传感器) |
| 中文描述： | 光到数字的I2C传感器（光电传感器的I2C） |
| 文件页数： | 8/10页 |
| 文件大小： | 196K |
| 代理商： | ISL29002 |
8
FN7465.2
December 1, 2006
integration is no longer fixed at 32,768, but varies with the
chosen integration time, and is limited to 65,536. In order to
avoid erroneous lux readings the integration must be short
enough not to allow an overflow in the counter register.
where:
T
int
= user defined integration time
f
osc
= 300kHz*100k
Ω
/R
EXT
. ISL29002’s internal oscillator.
Not to be confused with the I
2
C’s frequency.
R
EXT
= user defined external resistor to adjust f
osc
. 100k
Ω
recommended.
The number of clock cycles in the previous integration period
is provided in the third and fourth bytes of data read across
the I
2
C bus. This two-byte value is called the integration
counter value.
When using one of the three external timing modes, the
ISL29002’s resolution varies with the integration time. The
resolution is determined by the ratio of the max lux range to
the number of clock cycles per integration.
The following equations describe the light intensity as a
function of sensor reading, integration counter value, and
integration time:
EXT
T
int
= Time Interval between external time commands
where L is the measured light intensity, Data1 is the sensor
reading, Data2 is the integration counter value, T is the
integration time, and R
EXT
is external resistor value.
Noise Rejection and Integration Time
In general, integrating type ADC’s have an excellent noise-
rejection characteristics for periodic noise sources whose
frequency is an integer multiple of the integration time. For
instance, a 60Hz AC unwanted signal’s sum from 0ms to
n*16.66ms (n = 1,2...n
i
) is zero. Similarly, setting the
ISL29002’s integration time to an integer multiple of periodic
noise signal greatly improves the light sensor output signal
in the presence of noise. The integration time, T
int
, of the
ISL29002 is set by an external resistor R
EXT
.
See Equation 3.
Design Example 1
Using the ISL29002, determine a suitable integration time,
T
int
, that will ignore the presence of both 60Hz and 50Hz
noise. Accordingly, specify the R
EXT
value. Given that the
I
2
C clock is at f
I2C
= 10kHz.
Solution 1 -
Using Internal Timing
T
int
= n(1/60Hz) = m(1/50Hz). In order to achieve both 60Hz
and 50Hz AC rejection, the integration time needs to be
adjusted to coincide with an integer multiple of the AC noise
cycle times.
n/m = 60Hz/50Hz = 6/5. The first instance of integer values at
which T
int
rejects both 60Hz and 50Hz is when m = 5, and n =
6.
T
int
= 6(1/60Hz) = 5(1/50Hz) = 100ms
From Equation 3:
R
EXT
= T
int
* (100k
Ω
/110ms) = 90.9k
Ω
. By populating
R
EXT
= 90k
Ω
, the ISL29002 defaults to 100ms integration time
and will reject the presence of both 60Hz and 50Hz power line
signals.
Solution 2 -
Using External Timing
From solution 1, the desired integration time is 100ms. Note
that the R
EXT
resistor does not determine the integration time
when using external timing mode. Instead, the integration and
the 16-bit counter starts when an external timing mode
command is sent and end when another external timing mode
is sent. In other words, the time between two external timing
mode command is the integration time. The programmer
determines how many clock cycles to wait between two
external timing commands.
i
I2C
= f
I2C *
T
int
, where i
I2C
= number of I
2
C cycles
i
I2C
= 10kHz
*
100ms
i
I2C
= 1,000 I
2
C clock cycles. An external timing command
1,000 cycles after another external timing command rejects
both 60Hz and 50Hz AC noise signals.
IR Rejection
Any filament type light source has a high presence of infrared
component invisible to the human eye. A white fluorescent
lamp, on the other hand has a low IR content. As a result,
output sensitivity may vary depending on the light source.
Maximum attenuation of IR can be achieved by properly scaling
the readings of Diode1 and Diode2. The user obtains data
reading from sensor diode 1, D1, which is sensitive to visible
and IR, then reading from sensor diode 2, D2 which is mostly
sensitive from IR. The graph on Figure 9 shows the effective
spectral response after applying Equation 7 of the ISL29002
from 400nm to 1000nm. The equation below describes the
method of cancelling IR in internal timing mode.
Where:
data = lux amount in number of counts less IR presence
D1 = data reading of Diode 1
D2 = data reading of Diode 2
n = 1.85. This is a fudge factor to scale back the sensitivity up to
ensure Equation 2 is valid.
k = 7.5. This is a scaling factor for the IR sensitive Diode 2.
T
int
OSC
-----------------
<
(EQ. 5)
E lux
)
)
------------------------------------------
-----------------
=
(EQ. 6)
D3
n D1
kD2
–
)
=
(EQ. 7)
ISL29002
相关PDF资料 |
PDF描述 |
|---|---|
| ISL29003 | Light-to-Digital Output Sensor with High Sensitivity, Gain Selection, Interrupt Function and I2C Interface(具有高灵敏度，增益可选，中断功能和I2C接口的光电输出传感器) |
| ISL36356A-APDK-EVAL | PRISM 11Mbps Wireless Local Area Network Access Point |
| ISL36356A-APDK | PRISM 11Mbps Wireless Local Area Network Access Point |
| ISL3690IR-TK | Dual Band Direct Conversion Transceiver |
| ISL3690IR | Dual Band Direct Conversion Transceiver |
相关代理商/技术参数 |
参数描述 |
|---|---|
| ISL29002IROZ | 功能描述:IC SENSOR LIGHT-DGTL I2C 8-ODFN RoHS:是 类别:传感器，转换器 >> 光学 - 光电探测器 - 环境光传感器 系列:- 产品培训模块:Lead (SnPb) Finish for COTS Obsolescence Mitigation Program 产品变化通告:Product Discontinuation 25/Jun/2012 标准包装:2,500 系列:- 带接近传感器:无 波长:- 电源电压:1.7 V ~ 2 V 电流 - 暗（标准）:- 电流 - 光（典型值）:- 输出类型:数字 - I²C 工作温度:-40°C ~ 85°C 安装类型:表面贴装 封装/外壳:6-UDFN 裸露焊盘 包装:带卷 (TR) |
| ISL29002IROZ-EVALZ | 功能描述:EVALUATION BOARD FOR ISL29002 RoHS:是 类别:编程器，开发系统 >> 评估板 - 传感器 系列:- 产品培训模块:Lead (SnPb) Finish for COTS Obsolescence Mitigation Program 标准包装:1 系列:- |
| ISL29002IROZ-T7 | 功能描述:IC SENSOR LIGHT-DGTL I2C 8-ODFN RoHS:是 类别:传感器，转换器 >> 光学 - 光电探测器 - 环境光传感器 系列:- 产品培训模块:Lead (SnPb) Finish for COTS Obsolescence Mitigation Program 产品变化通告:Product Discontinuation 25/Jun/2012 标准包装:2,500 系列:- 带接近传感器:无 波长:- 电源电压:1.7 V ~ 2 V 电流 - 暗（标准）:- 电流 - 光（典型值）:- 输出类型:数字 - I²C 工作温度:-40°C ~ 85°C 安装类型:表面贴装 封装/外壳:6-UDFN 裸露焊盘 包装:带卷 (TR) |
| ISL29003IROZ | 功能描述:IC SENSOR LIGHT-DGTL I2C 6-ODFN RoHS:是 类别:传感器，转换器 >> 光学 - 光电探测器 - 环境光传感器 系列:- 产品培训模块:Lead (SnPb) Finish for COTS Obsolescence Mitigation Program 产品变化通告:Product Discontinuation 25/Jun/2012 标准包装:2,500 系列:- 带接近传感器:无 波长:- 电源电压:1.7 V ~ 2 V 电流 - 暗（标准）:- 电流 - 光（典型值）:- 输出类型:数字 - I²C 工作温度:-40°C ~ 85°C 安装类型:表面贴装 封装/外壳:6-UDFN 裸露焊盘 包装:带卷 (TR) |
| ISL29003IROZ-EVALZ | 功能描述:EVALUATION BOARD FOR ISL29003 RoHS:是 类别:编程器，开发系统 >> 评估板 - 传感器 系列:- 产品培训模块:Lead (SnPb) Finish for COTS Obsolescence Mitigation Program 标准包装:1 系列:- |
发布紧急采购，3分钟左右您将得到回复。